Barco Projector Cineversum 80 Quickstart Manual

							18. Additional settings Cine VERSUM Master
18. ADDITIONAL SETTINGS CINE VERSUM MASTER
Overview
• Output Resolution set up
• Display Internal Generated Pattern
• Shutdown Automatic when no signal
• Source Transition
• On Screen Display Configuration
• On-Screen Display Language
• Display Name Change
18.1 Output Resolution set up
Why Output Resolution set up?
In case the digital video distribution system contains a combination of a Cine VERSUM 50 (Resolution 1280/768), a Cine VERSUM
80 (Resolution 1280/720) and/or a Cine VERSUM 120 (Resolution 1280/720), then the Cine VERSUM Master has to scale his output
resolution to one of these displays.
When selecting the resolution of the Cine VERSUM 80 or the Cine VERSUM 120, then the picture on the Cine
VERSUM 50 is displayed with a black bar at the bottom. The latter can occurs burning-in of the plasma screen.
For that reason, selection of the output resolution referring to Cine VERSUM 50 is recommended. On the other
hand, the highest output resolution occurs for the Cine VERSUM 80 and the Cine VERSUM 120 a lost of lines
at the bottom.
How to set up the output resolution
1. Select the INSTALLATION menu (see Loading a File, page 97).
2. Select itemOUTPUTby rotating the jog dial on the Master or the↑or↓keys on the Remote Control. (menu 18-1)
3. Press the jog dial on the Master or the keyENTERon the Remote Control to toggle betweenSMALLESTorLARGEST.
- Selecting ’Smallest’: default output resolution to displays is 1280/720, occurring full image on the Cine VERSUM 80/Cine
VERSUM 120 and a picture with a black bar on the bottom for the Cine VERSUM 50. (image 18-1)
- Selecting ’Largest’: default output resolution to displaysis 1280/768, occurring full image on the Cine VERSUM 50 and lost
of lines on bottom on Cine VERSUM 80/Cine VERSUM 120 (May be a problem with subtitles). (image 18-2)
4. Press theEXITkey on the Remote Control or select item BACK on the graphical display, by rotating the jog dial followed by
pressing it, to leave the GUI menus.
Installation
Input slots
File service
Display list
Internal pattern
When no signal
Source transition
OSD Configuration
Language
Keystone
Global keystone: Yes
Output: [Largest]
Default input balance
Back
Menu 18-1
R5976468 CINE VERSUM SYSTEM 03112003127 
						

							18. Additional settings Cine VERSUM Master
Image 18-1
Picture on display
Image 18-2
Picture on display
18.2 Display Internal Generated Pattern
How to display an internal pattern
In total 10 different internal patterns (Generated in the Cine VERSUM Master) can be displayed instead of the selected source. To
select a pattern, carry out the following steps:
1. Select the INSTALLATION menu (see Loading a File, page 97).
2. Select item INTERNAL PATTERN by rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu INTERNAL PATTERNS appears on-screen and in the graphical display, including a list of available internal gen-
erated patterns. (menu 18-2)
4. Select the pattern you desire to display by rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The image from the selected source will be replaced by the selected internal test pattern. Press again to reverse the image. For
the purity test pattern, the different purity patterns, Black-Green-Red-Blue-White, are selected consecutively by pressing again
theENTERkey or the jog dial. (image 18-3)
6. Press theEXITkey on the Remote Control or select item BACK on the graphical display, by rotating the jog dial followed by
pressing it, to leave the GUI menus.
Internal Patterns
Background
Outline
Hatch
Color bars
Gray bars
Multiburst
Checkerboard
Purity
Alphanumeric
Page Character
Back
Menu 18-2
128R5976468 CINE VERSUM SYSTEM 03112003 
						

							18. Additional settings Cine VERSUM Master
Image 18-3
Available testpatterns
18.3 Shutdown Automatic when no signal
How to setup the automatic shutdown
If no input signal is available for a delay of minimum 40 seconds, the Cine VERSUM Master can be setup for automatic shutdown
(Standby mode).
1. Select the INSTALLATION menu (see Loading a File, page 97)
2. Select itemWHEN NO SIGNALby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu WHEN NO SIGNAL appears on-screen and in the graphical display, including the status of the shutdown, On or
Off. If the status is ’Off’, then the delay time can not be adjusted (text is displayed in gray). (menu 18-3)
4. Select itemSHUTDOWNby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
5. Press the jog dial on the Master or the keyENTERon the Remote Control to toggle the status of the Shutdown to ’On’.
ItemDELAYbecomes active (text displayed in black) allowing to change the delay time.
6. Select itemDELAYby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
7. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The menu box SHUTDOWN DELAY, requesting to enter new valuesfor 2 numbers (=delay time) appears on-screen and in the
graphical display . The first character is highlighted and can be filled in. After the second number has been putted in, the data is
saved automatically.
8. Continue with filling in the 2 numbers consecutively as follows:
- Pressing the cursor keys↑or↓on the Remote Control or rotating the jog dial on the Master allows to select the characters.
- Pressing the cursor keys←or→on the Remote Control or pressing the jog dial on the Master allows to change the character
( Numeric characters can be entered remotely with the numeric keys).
9. PressEXITon the Remote Control to return or select BACK in the menu by rotating the jog dial on the Master or the↑or↓keys
on the Remote Control, confirmed by pressing the jog dial or theENTERkey.
When No signal
Shutdown [On]
Delay (min): 40
Back
Menu 18-3
R5976468 CINE VERSUM SYSTEM 03112003129 
						

							18. Additional settings Cine VERSUM Master
18.4 Source Transition
Source transition
Seamless transition mode can be applied during input source switching. There is a choice between 14 different effects which render
the transitions more enjoyable.
How to enter the source transition effect
1. Select the INSTALLATION menu (see Loading a File, page 97)
2. Select itemSOURCE TRANSITIONby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu SOURCE TRANSITION appears on-screen and in the graphical display, including a list of available source tran-
sition effects. The already active transition effect is indicated with a asterisk placed in front of the name. (menu 18-4)
4. Select the transition effect you desire to apply by rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
Confirmation is indicated with a asterisk placed in front of the new selected source transition effect.
6. PressEXITon the Remote Control to return or select BACK in the menu by rotating the jog dial on the Master or the↑or↓keys
on the Remote Control, confirmed by pressing the jog dial or theENTERkey.
Source transition
None
Fade
Wipe Right
Wipe Down
*Split
Box
Checkerboard (1)
More..
Back
Menu 18-4
Source transition
Checkerboard (2)
Worm
Clock
Worms
Diagonal
Wobble
Slide
Random
More..
Back
Menu 18-5
18.5 On Screen Display Configuration
Overview
• About the OSD (Menu, Bar Scale and Message)
• Status Change of the OSD
• On Screen Display Position Alignment
18.5.1 About the OSD (Menu, Bar Scale and Message)
OSD switching On/Off
To allow image adjustments during a performance without disturbingtheimagebytheOSD,theOnScreenDisplaycanbeturned
off in 2 ways:
130
R5976468 CINE VERSUM SYSTEM 03112003 
						

							18. Additional settings Cine VERSUM Master
Image 18-4
•PressthekeyTEXTon the Remote Control. The OSD’s, included Menu, Bar scale and Message are disabled. To reactivate
the OSD, press the keyTEXTagain. Attention, only the OSD’s (including MENU, BAR SCALE and MESSAGE) with status ’On’
will be active again.
• Via the OSD configuration menu. Disabling and enabling the display (=changing the status) for respective Menu, Bar scale and
Messages, has to be done for each item separately.
18.5.2 Status Change of the OSD
How to change the status of the OSD
The status of the OSD can be changed in the OSD Configuration menu. The menu is displayed on-screen, if status of the Menu is
set to ’on’, and in the graphical display on the Cine VERSUMMaster. In case of a non active Menu OSD (=status ’Off’), refer to the
menu in the graphical display on the Cine VERSUM Master.
1. Select the INSTALLATION menu using the respective keys on the Remote Control or the jog dial on the Cine VERSUM Master.
2. Select itemOSD CONFIGURATIONby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu OSD CONFIGURATION appears on-screen (If Menu status is ’On’) and in the graphical display, including the
status setting of the bars cale, the menu and Messageas well as the alignment of the position of it (not for the Message box).
(menu 18-6)
4. Select the OSD item you want to change the status by rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
5. Press the jog dial on the Master or the keyENTERon the Remote Control to toggle the status from On to Off or back to On.
6. PressEXITon the Remote Control to return or select BACK in the menu by rotating the jog dial on the Master or the↑or↓keys
on the Remote Control, confirmed by pressing the jog dial or theENTERkey.
OSD Configuration
Menu Status [On]
Menu Position
V:[Center]
H:[Center]
Barscale Status [On]
Barscale Position
V:[Center]
H:[Center]
Message Status [On]
Back
Menu 18-6
R5976468 CINE VERSUM SYSTEM 03112003131 
						

							18. Additional settings Cine VERSUM Master
18.5.3 On Screen Display Position Alignment
How to define the position of the OSD
The position of the OSD for the Menu and the Bar scale is adjustable. The vertical and the horizontal position of the OSD are
adjustable and are located in the menu below the respective OSD name, Menu position and Bar scale position. The procedure is
for both the same. Follow the next steps:
1. Select the OSD adjustable item you want to change by rotating the jog dial on the Master or the↑or↓keys on the Remote
Control. (menu 18-7)
2. Press the jog dial on the Master or the keyENTERon the Remote Control to toggle between Top, Center and Bottom in case of
Vertical position, and between left, Center and Right in case of Horizontal position.
The OSD jumps to the selected position on the screen.
3. PressEXITon the Remote Control to return or select BACK in the menu by rotating the jog dial on the Master or the↑or↓keys
on the Remote Control, confirmed by pressing the jog dial or theENTERkey.
OSD Configuration
Menu Status [On]
Menu Position
V:[Center]
H:[Center]
Barscale Status [On]
Barscale Position
V:[Center]
H:[Center]
Message Status [On]
Back
Menu 18-7
18.6 On-Screen Display Language
How to change the language of the menus
When entering the Language menu, the available languages are displayed. The active language is indicated with a asterisk in front
of the language name.
1. Select the INSTALLATION menu using the respective keys on the Remote Control or the jog dial on the Cine VERSUM Master.
(menu 18-8)
2. Select itemLANGUAGEby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu LANGUAGE appears on-screen and in the graphical display, including the available languages. (menu 18-9)
4. Select the desired language by rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The language changes to the selected one and is indicated in the menu with an asterisk in front of the language name.
6. PressEXITon the Remote Control to return or select BACK in the menu by rotating the jog dial on the Master or the↑or↓keys
on the Remote Control, confirmed by pressing the jog dial or theENTERkey.
Installation
Input slots
File service
Display list
Internal pattern
When no signal
Source transition
OSD Configuration
Language
Keystone
Global keystone: Yes
Output: [Largest]
Default input balance
Back
Menu 18-8
Language
*English
Dutch
French
Back
Menu 18-9
132R5976468 CINE VERSUM SYSTEM 03112003 
						

							18. Additional settings Cine VERSUM Master
18.7 Display Name Change
Where to find the display RENAME function
InstallationInput Slots
File Service
Display List
Internal Pattern
W hen no signal
Source Transition
OSD configuration
Language
Keystone
Global Keystone:Yes
Output: [Largest]
Default Input Balance
Back
Main Menu/Installation/Display List/Display Settings
Display Settings Switch OFF
 Display Info
 Rename
 IR Address 009
 Diagnosis
Back
Cine VERSUM r01
Display List1 CV50  On
2 CV80 On
3 CV120 On
Back
Display Settings Switch OFF
 Display Info
 Rename
 IR Address 009
 Diagnosis
 CW  Index
 Orientation
 Test patterns
BackDisplay Settings Switch OFF
 Display Info
 Rename
 IR Address 009
 Diagnosis
 Orientation
 Test patterns
 Lens
 Lamp
Back
Display NameEnter new name
- - - - - - - - - - - - - - - - - - - -
Cine VERSUM 50Cine VERSUM 80 Cine VERSUM 120
Image 18-5
Rename function search
How to change the name of a display
When starting up the system for the first time, the name of the detected displays, registered in the display list, is the serial number
of the respective display. The name can contain maximum20 characters. To change the name, follow next steps:
1. Select the INSTALLATION menu using the respective keys on the Remote Control or the jog dial on the Cine VERSUM Master.
(menu 18-10)
2. Select itemDISPLAY LISTby rotating the jog dial on the Master or the↑or↓keys on the Remote Control.
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The Display List menu appears on-screen and in the graphical display showing the detected displays, inclusive address number,
display name (can be renamed) and status. (menu 18-11)
4. Select the display, you desire to change the name, by rotating the jog dial on the Master or the up/down arrow keys on the Remote
Control.
5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The Display Settings menu for that particular display appears on-screen and in the graphical display showing the specific items
for the selected display (image 18-5).
6. Select item RENAME by rotating the selection wheel on the Master or the up/down arrow keys on the Remote Control.
7. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The DISPLAY NAME menu appears on-screen and in the graphical display on the Master requesting to enter a new display name
(max 20 characters). (menu 18-12)
8. Start with filling in the new name, (Always 20 characters) as follows:
- Pressing the cursor keys←or→on the Remote Control or pressing the jog dial on the Master allows to select the character
position.
- Pressing the cursor keys↑or↓on the Remote Control or rotating the jog dial on the Master allows to change the character (
Numeric characters can be entered remotely with the numeric keys).
9. When the last character of the display name has been entered, a message box pops up, confirming saving data.
The message box disappears after a few seconds. (menu18-13)
Installation
Input slots
File service
Display list
Internal pattern
When no signal
Source transition
OSD Configuration
Language
Keystone
Global keystone: Yes
Output: [Largest]
Default input balance
Back
Menu 18-10
Display List
2CV50 1:On
3 CV50 2: Off (Stdby)
4CV80 1:On
5 CV120 1: Off (Stdby)
6CV80 2:On
Back
Menu 18-11
Display Name
Enter new name
9:xxxxxxxxxxxxxxxxxxxx:On
Back
Menu 18-12
Message
Saving Data
Menu 18-13
R5976468 CINE VERSUM SYSTEM 03112003133 
						

							18. Additional settings Cine VERSUM Master
134R5976468 CINE VERSUM SYSTEM 03112003 
						

							19. Picture in Picture (PIP)
19. PICTURE IN PICTURE (PIP)
Overview
• Turning On/Off the Picture in Picture
• Selecting Input Source for PIP Window
• Configuration of the PIP Window
What is Picture in Picture
If PIP is enabled, a window is inserted in the active image, in which the image of another selected input source will be displayed.
The position and the size of the window is adjustable. How to turn On/Off and adjusting the size and position of the PIP window,
see below.
19.1 Turning On/Off the Picture in Picture
How to turn On/Off the PIP
1. Select the ADVANCED SETTINGS menu (Adjusting the Image Aspect Ratio, page 107
2. Select item PIP CONFIGURATION by rotating the selection wheel on the Master or the up/down arrow keys on the Remote
Control. (menu 19-1)
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu PIP CONFIGURATION appears on-screen and in the graphical display. This menu contains the items PIP toggle
function On/Off, Vertical and Horizontal shift and size alignment. (menu 19-2)
4. Select item PIP [yes] by rotating the jog dial on the Master or the up/down arrow keyson the Remote Control to confirm.
5. Press theENTERkey on the Remote Control or the jog dial on the Master to toggle the PIP function On (Yes) or Off (No).
6. PressEXITkey on the Remote Control or select item BACK to return.
Advanced Settings
Aspect Ratio
Position
Pip Configuration
Blanking
Phase
Input Balance
Back
Menu 19-1
PIP Configuration
PIP [Yes]
Horizontal Shift
Horizontal Size
Vertical Shift
Vertical Size
Back
Menu 19-2
19.2 Selecting Input Source for PIP Window
How to select input source for PIP window
The procedure below supposes an already selected input source (main image) and the PIP function set to ’Yes’.
1. Select the input source, remotely accessible with the digit keys on the Remote Control, you desire to be displayed into the PIP
window.
If no valid source is connected to the input of the selected input module, no PiP window appears.
If a valid source is connected to the input, the selected input appears as PiP window on the screen. (image 19-1)
2. If the same input source (PIP image) is selected again, then, the main image is replaced by the PIP image and the PiP window
disappears.
R5976468 CINE VERSUM SYSTEM 03112003
135 
						

							19. Picture in Picture (PIP)
Image 19-1
Picture in Picture
When a PiP window is on the screen, zapping over inputs change only the PiP window. When the same source
is pressed twice, the selected source becomes the main window and the PiP window disappears.
19.3 Configuration of the PIP Window
How to configure the PIP window manually
1. Select the PIP Configuration menu (Turning On/Off the Picture in Picture, page 135).
2. Select the item you desire to adjust by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control.
(menu 19-3)
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The corresponding bar scale appears on-screen and in the graphical display of the Master. (image 19-2)
4. Adjust the Size or Shift (Position on the image)
- With the Remote Control: press the↑and↓key for Top/Bottom blanking, and the←and→key for Left/Right blanking.
- With the selection wheel on the Master: rotate the jog dial to the left or to the right.
5. Press EXIT on the Remote Control or press the jog dial on the Master to return.
PIP Configuration
PIP [Yes]
Horizontal Shift
Horizontal Size
Vertical Shift
Vertical Size
Back
Menu 19-3
Image 19-2
PIP configuration
How to configure the PIP window quickly
The function keys F1 to F5 on the Remote Control have the following action:
136
R5976468 CINE VERSUM SYSTEM 03112003