Barco Projector Cineversum 120 Quickstart Manual

11. Powering on/off the Cine VERSUM System
11. POWERING ON/OFF THE CINE VERSUM SYSTEM
Getting started
After power, source and link cables have been installed, proceed to start up of the Cine VERSUM System.
Overview
• Powering ON the Cine VERSUM System
• Status of the System after powering up
• Display Info ’New Display’ and ’Lost Display’
Powering on/off
Powering on/off is understood to mean switching on (to standby mode) and OFF the modules by means of its own power switch.
11.1 Powering ON the Cine...

11. Powering on/off the Cine VERSUM System
Status of the modules in the system (Case B)
Status modulesCine VERSUM Master, Cine VERSUM 50, Cine VERSUM 80 and
Cine VERSUM 120 in standby mode.
Standby LED on Cine VERSUM MasterBlinks (0.2s on/2s Off)
Standby LED on Connected DisplayBlinks (0.2s on/2s Off)
(For Cine VERSUM 50, blinking is superposed on already lightning
up standby LED)
Display on Cine VERSUM MasterStart up menu (menu 11-2) preceded by messages indicating the
detected displays (menu 11-3)....

11. Powering on/off the Cine VERSUM System
Message Lost display
CineVERSUM _________
Menu 11-5
R5976468 CINE VERSUM SYSTEM 0311200379 

11. Powering on/off the Cine VERSUM System
80R5976468 CINE VERSUM SYSTEM 03112003 

12. Image Projection after Powering Up
12. IMAGE PROJECTION AFTER POWERING UP
Overview
• Image Projection Using the Jog Dial on Cine VERSUM Master
• Image Projection Using the Remote Control
• Lamp Mode Set Up for Cine VERSUM 120 Only
Picture display can be started up using the selection wheel on the Cine VERSUM Master or using its Remote
Control.
12.1 Image Projection Using the Jog Dial on Cine VERSUM Master
How starting the image projection
1. Press the jog dial on the Cine VERSUM Master (On Cine...

12. Image Projection after Powering Up
How starting the image projection (Case C)
1. Press the ADJ or ENTER key (On InfraRed Remote Control, page 30). Menu on graphical display changes as follows –menu 12-1.
2. Press the cursor keys↑or↓to select item ’Power Up’ (arrow in front of item).
3. Press ENTER to confirm. The Cine VERSUM Master starts up, indicated by the message ’Power up’ in the display (menu 12-2).
The Cine VERSUM Master starts operation mode and starts on its turn image projection on the...

12. Image Projection after Powering Up
12.3.2 Lamp Mode Set Up Economic/Normal (Image Settings menu)
How to set up:
1. Enter the MAIN menu and scroll through the sub menus, using the jog dial or the Remote Control until the Image Settings menu
is displayed. (image 12-2)
2. Select menu itemLAMP POWERand enter the lamp mode ’Economic’ or ’Normal’ by pressing the jog dial or theENTERkey on
the Remote Control.
Note:To increase the lamp life time, enter the economic lamp power mode.
3. Leaving the GUI, use...

12. Image Projection after Powering Up
84R5976468 CINE VERSUM SYSTEM 03112003 

13. Projection Stop (Standby or Economic Standby mode)
13. PROJECTION STOP (STANDBY OR ECONOMIC
STANDBY MODE)
Overview
• Projection Stop Using the Selection Wheel
• Projection Stop Using the Remote Control
Economic Standby for the Cine VERSUM Master only: in this mode, the power dissipation is reduced and the
system stays operational for re-start of the system.
13.1 Projection Stop Using the Selection Wheel
How to stop image projection
1. Press the jog dial on the Cine VERSUM Master. Scroll through the...

13. Projection Stop (Standby or Economic Standby mode)
13.2 Projection Stop Using the Remote Control
Overview
• Direct System Shutdown (standby)
• System Shutdown (standby) via screen menu
13.2.1 Direct System Shutdown (standby)
The On Screen menus on the Cine VERSUM 50, Cine VERSUM 80 and Cine VERSUM 120are with respect to
content identic. Nevertheless, some items are specific for a display and are therefore grayed out if not ap-
plicable for that specific display. Make sure that the Remote control...