Barco Projector Cineversum 120 Quickstart Manual

5. Location of Controls
5. LOCATION OF CONTROLS
Overview
• On Cine VERSUM Master
•OnCineVERSUM50
•OnCineVERSUM80
• Cine VERSUM 120
• On InfraRed Remote Control
5.1 On Cine VERSUM Master
Front View
The front side of the Cine VERSUM Master is provided with the following controls:
Image 5-1
Front side Cine VERSUM Master
Controls function description
Ref.FunctionDescription
1Infra Red Reception LED indicatorLights up when a valid IR signal from the Remote Control has been
captured.
2Infra Red ReceiverInfra...

5. Location of Controls
The status of the Plasma screen is indicated by a blue LED (3), located at the bottom on the right of the screen. In the same corner
an IR Sensor (2) is mounted to allow controlling the Cine VERSUM system via the screen.
Image 5-2
Cine VERSUM 50 controls
Controls function description
Ref.FunctionDescription
1Main Power SwitchSwitches the Cine VERSUM 50 in the Standby mode or operation mode. In these
modes, the Cine VERSUM 50 is controlled by the Cine VERSUM Master or remotely
on...

5. Location of Controls
Ref.FunctionDescription
2Infra Red Reception LED indicatorLights up when a valid IR signal from the Remote Control has been
captured.
3Standby LEDLights up continuously: projector in the operation mode.
Repeatedly blinks 2 times successively, followed by a long time Off:
projector in the standby mode
Blinks fast: projector in the cooling down mode after switching off
(duration 1 min.).
Lights up repeatedly 1 time long, 1 time short: projector has been started
up in the cooling...

5. Location of Controls
Ref.FunctionDescription
3Standby LEDLights up continuously: projector in the operation mode.
Lights up repeatedly 2 times short on, 1 time long off: projector in the
standby mode
Blinks fast: projector in the cooling down mode after switching off
(duration 1 min.).
Lights up repeatedly 1 time long, 1 time short: projector has been started
up in the cooling down mode, waiting for lamp ignition.
4Not used
5Infra Red Reception LED indicatorLights up when a valid IR signal from the...

5. Location of Controls
Controls function description
Ref.FunctionDescription
1Function keysTo position the PIP image in the displayed image.
2ADJ (Adjust key)Toggle key to enter or to exit the adjustment mode.
3Address keyTo match the address of the RCU with the Cine VERSUM Master (number between
0 and 9).
4*keySelecting the aspect ratio of the displayed image to the source.
5PA U S ETo blank the image of the linked displays
6Standby keyTo power up/down the Cine VERSUM Master and separately the displays...

5. Location of Controls
32R5976468 CINE VERSUM SYSTEM 03112003 

6. Installation Guidelines
6. INSTALLATION GUIDELINES
Overview
• Projector Installation Guidelines
• Plasma Screen Installation Guidelines
6.1 Projector Installation Guidelines
Overview
• General Installation Guidelines
• Image Projection
6.1.1 General Installation Guidelines
Before installing the projector, read first the safety instructions.
Temperature and humidity conditions
• The installation site should meet the following conditions:
- Operating temperature: 10 to 35 °C (largely depending on...

6. Installation Guidelines
Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount
of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms of gain.
The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a gain of 10 (x10)
or more. The choice between higher and lower gain screens is largely a matter of personal...

6. Installation Guidelines
Front Projection (Ceiling-Table mounted)
Image 6-1
Front projection
1 Table standing
2 Ceiling mounted
It is recommended that you use the optional BARCO ceiling-mount bracket to mount the projector to the ceil-
ing.
Projection Using a Mirror
Image 6-2
Rear: Mirror projection
Rear Projection (Ceiling-Table mounted)
Image 6-3
Rear projection
1 Table standing
2 Ceiling mounted
R5976468 CINE VERSUM SYSTEM 03112003
35 

6. Installation Guidelines
It is recommended that you use the optional BARCO ceiling-mount bracket to mount the projector to the ceil-
ing.
6.1.2.3 Projector distance adjustment
Cine VERSUM 80: Calculation of the projector distance PD
Place the projector at the required distance from the screen according to the desired screen size. The required distance can be
calculated with the formula added to the drawing below.
The formula is based upon projecting an 16:9 image so that it occupies the entire 16:9...