Barco Projector Cineversum 120 Quickstart Manual

17. Adjusting the Picture
8. Select the Orientation item which suit the projector mounting by rotating the jog dial on the Master or the up/down arrow keys on
the Remote Control.
9. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The projector fits to the selected image orientation and the system returns to operation automatically after a few seconds. (im-
age 17-1)
Installation
Input slots
File service
Display list
Internal pattern
When no signal
Source transition
OSD...

17. Adjusting the Picture
5. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu ASPECT RATIO appears on-screen and in the graphicaldisplay, including all available aspect ratios. (menu 17-10)
Explanation
Aspect RatioDescription
FitForces format of all input signals into the native panel resolution.
16:9Wide screen television format/Anamorf format.
4:3Standard television format.
5:4Workstations format.
2.35Panavision or Cinemascope format, frequently used by...

17. Adjusting the Picture
17.4 Adjusting the Decoding Standard
About Decoding Standard
The possibility is offered to decode the NTSC video signals via the default American IRE standard (Decoding a NTSC signal using
the European EBU standard may result in a greenish tint.) and the PAL/SECAM video signals via the European EBU standard.
When the PROJECTOR standard has been chosen, then, video signal are decoded based on the installed Color Parameters.
Choice of the color decoding standard is applicable on...

17. Adjusting the Picture
CineVERSUMImage  settings
Advanced Settings
Installation
Service
1 NO MODULE
2 NO MODULE
3 VIDEO [VIDEO]
4 NO MODULE
5 NO MODULE
6 NO MODULE
7 RGB-YUV [RGB]
8 NO MODULE
Shut Down
BackImage SettingsMaster
  Brightness
  Contrast
  Saturation
  Tint
Display
Back
Display List1 CV50  On
2 CV80 On
3 CV120 On
Back[On/Off]
Cine VERSUM r01
If the CV80 is the only display in the linkCV80
Main Menu/Image Settings/Display/CV80 or CV120 /Primaries
Image SettingsDisplay
  Brightness...

17. Adjusting the Picture
4. Select item GLOBAL KEYSTONE: YES by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control
(menu 17-12).
5. Set Global Keystone to Yes or to No, using the jog dial on the Master or the keyENTERon the Remote Control as toggle switch.
- Confirmation YES: Keystone correction will be applied to ALL files.
- Confirmation NO: keystone correction will be applied to the ACTIVE file.
Cine VERSUM System
Image Settings
Advanced Settings
Installation
Service...

17. Adjusting the Picture
17.7 Adjusting the Image Shift and Size
Overview
• Adjusting the Image Shift
• Adjusting the Image Size
17.7.1 Adjusting the Image Shift
How to adjust the Vertical and Horizontal image shift
1. Select the ADVANCED SETTINGS menu (menu 17-8).
2. Select item POSITION by rotating the jog dial on the Master or the up/down arrow keys on the Remote Control. (menu 17-14)
3. Press the jog dial on the Master or the keyENTERon the Remote Control to confirm.
The sub menu POSITION appears...

17. Adjusting the Picture
17.7.2 Adjusting the Image Size
How to adjust the Vertical and Horizontal image size
1. Select sub menu POSITION (Adjusting the Image Shift, page 112)
2. Select the SIZE item, vertical or horizontal, you desire to adjust by rotating the selection wheel on the Master or the up/down
arrow keys on the Remote Control. (menu 17-16)
3. Press the selection wheel on the Master or the key ENTER on the Remote Control to confirm.
A barscale with zero point appears on-screen and in the...

17. Adjusting the Picture
6. Adjust the blanking:
- With the Remote Control: press the←or→key to adjust the blanking level.
- With the jog dial on the Master: rotate the jog dial to the left or to the right.
7. PressEXITon the Remote Control or press the jog dial on the Master to return.
Blanking
Top
Bottom
Left
Right
Back
Menu 17-17
Image 17-8
Blanking adjustment
17.9 Alignment of the Input Balance
Overview
• Input Balance Selection
• Input Balance Adjustment
About the Input Balance alignment
Two kind...

17. Adjusting the Picture
Advanced Settings
Aspect Ratio
Position
Pip Configuration
Blanking
Phase
Input Balance
Back
Menu 17-19
The ’Default Input Balance’ is used to align the input balance of the different modules referring to standard input signals.
As standard input signals are required for the alignment of the Default Input Balance, this alignment has to
be consider as FACTORY ALIGNED. Attempting to align the Default Input Balance can have serious conse-
quences on the image performances. For that...

17. Adjusting the Picture
17.9.2 Input Balance Adjustment
How to adjust the Input Balance
Always start with the Black balance adjustment ifa dominant color has been observed in both areas.
1. Select in the Input Balance menu item BLACK BALANCE and confirm.
A sub menu appears on-screen and in the graphical display, showing the adjustable items Black Level RED and BLUE.
(menu 17-21)
2. Select, depending the color dominant, in the Black Balancemenu item BLACK LEVEL RED or Blue and confirm. If necessary...