Barco Projector Cineversum 110 Quickstart Manual

							2. Installation Guidelines
Image 2-6
2.6.4 Cleaning the lens
To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have de-
veloped recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from
the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.
Necessary tools
To r a y s e eTMcloth (delivered together with the lens kit). Order number : R379058.
Howtocleanthelens?
Proceed as follow :
1. Always wipe lenses with a CLEAN Toraysee
TMcloth.
2. Always wipe lenses in a single direction.
Warning:Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.
3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.
4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.
WARNING:Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the
cloth.
Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.
CAUTION:Other lenses can also be cleaned safely with this TorayseeTMcloth.
2.7 Ceiling mount support for CineVERSUM™ 110
Overview
Order number : R9842330
R9842330
Image 2-7
Ceiling mount support
For more details about the ceiling mount support, see the concerning installation manual.
Ceiling mount extension supports.
R5976697 CINEVERSUM™ 110 12/05/2004
17 
						

							2. Installation Guidelines
Image 2-8
Ceiling mount extension support
For more details about the ceiling mount extension supports, see theconcerning installation manual.
2.8 Battery Insertion in the Remote Control
Where to find the batteries
The batteries are not placed in the remote control to avoid remote control operation in its package, resulting in a shorter battery life
time.
How to install the batteries
1. Push the cover tab (A) with the fingernail a little backwards and pull upwards the cover top (B). (image 2-9)
2. Slide the cover forwards to remove. (image 2-10)
3. Push the battery body towards the spring and lift it up to remove. (image 2-11)
4. Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment (image 2-11).
5. Insert the lower tab of the battery cover in the gap atthe bottom of the remote control, and press the cover until it clicks in place
(image 2-10).
Image 2-9
Battery cover unlock
Image 2-10
Battery cover removal
18R5976697 CINEVERSUM™ 110 12/05/2004 
						

							2. Installation Guidelines
Image 2-11
Battery removal
R5976697 CINEVERSUM™ 110 12/05/200419 
						

							2. Installation Guidelines
20R5976697 CINEVERSUM™ 110 12/05/2004 
						

							3. Connections
3. CONNECTIONS
Overview
• Power connection
• Input source connection
• 5-Cable input
• Composite Video Input
• S-Video input
• Digital Visual Interface (DVI) input
• Computer input (RGB analog)
• Serial Digital Interface
• RS232 IN connection
• Extended configuration
3.1 Power connection
3.1.1 Supplied Power Cords
The following power cords are added to the product
In the package of each product, two power cords are added, one with a plug shape, reference standard ANSI C73.11, and one with
a plug shape, reference CEE (7).
Image 3-1
Power cord ANSI (L-shaped socket) for CineVERSUM™ 110Image 3-2
Power cord CEE (L-shaped socket) for CineVERSUM™ 110
ANSI 73.11
American power plug to connect the power cord to the wall outlet.
CEE7
European power plug to connect the power cord to the wall outlet.
3.1.2 Power Connection CineVERSUM™ 110
AC Power Cord connection
Use the supplied power cord to connect the CineVERSUM™ 110 to thewall outlet. First, remove the back cover (1) (turn the quarter
turn fastener a quarter turn counterclockwise to unlock cover) and the power input cover (2) to allow the power plug insertion. Then,
plug the female power connector into the male connector at the rear of the unit. Make sure that the power plug is firmly inserted into
the AC socket and the power cable routed from the bottom side.
R5976697 CINEVERSUM™ 110 12/05/2004
21 
						

							3. Connections
A 12Image 3-3
Projector covers removal
A Quarter turn fastener
1 Rear cover
2 Power input cover
A
B
Image 3-4
Power connection
A Right angle power socket
B Power cable routing
AC Power Specifications
AC Power VoltageAuto Range 90 – 240V
AC Power Current7.0 A – 2.9 A/ 50–60Hz
Main FuseMain Power Supply: T15A H 250V
Power Consumption
Normal operation mode650 W (Dual lamp)-355 W (Single lamp)
Standby mode14 W
3.2 Input source connection
Overview
• Input section
• Input facilities
3.2.1 Input section
Input Layers
The input section is divided in layers, each of them regrouping several inputs, this architecture allows the input section to be upgraded
at any time with an optional analog or digital layer.
1. Layer 1: analog layer containing analog data and video inputs.
2. Layer 2: a hybrid layer containing 2 digital and 1 analog input.
3. Layer 3 : SDI digital layer.
22
R5976697 CINEVERSUM™ 110 12/05/2004 
						

							3. Connections
3.2.2 Input facilities
overview
• 5–cable input
- component video (PR/Y/PB)
-RGBS
• composite video
•S-Video
• Digital Visual Input (DVI)
• Computer (analog RGB)
• Serial Digital Input with loop through connection
R/PRG/YB/PBHs/CsVsVIDEO
SDI
INSDI
OUTS-VIDEO
R.C.DVI ANALOG RGB RS 232 C
L1
L2
L3
Image 3-5
Input facilities
L1 Layer 1 = RGBHV + Composite Video + S-Video
L2 Layer 2 = DVI + Computer + RS232IN + RC (wired remote control)
L3 Layer 3 = SDI in and out
3.3 5-Cable input
Input specifications
The 5-cable input section is made of 5 BNC input terminals.
0.7 Vpp ± 3dB
75Ωterminated
R/PRG/YB/PBHs/CsVsVIDEO
SDI
INSDI
OUTS-VIDEO
R.C.DVI ANALOG RGB RS 232 C
Image 3-6
5-cable input
R5976697 CINEVERSUM™ 110 12/05/200423 
						

							3. Connections
Component Video
In Component Video the term component describes a number of elements that are needed to make up the video pic-
ture, these components are PR/Y/PB. A composite video signal on the other hand contains all the information needed
for the color picture in a single channel of information
Which signals can be connected ?
Signals/Input BNCRGBHV
RGBHVRGBHV
RGsB1RGsB--
RGBS1RGBS-
ComponentPRYPB--
Beside the standard RGB, component and sync signals, the extended mode of the 5 Cable input makes pro-
cessing of additional signals possible.
How to select a source on the 5 cable input ?
1. Press1on the RCU
Note:Another way for selecting this input is viaSourceon the local keypad or via the Menu
Component Video signals (PR/Y/PB)
Some interfaces use progressive output signals with a double line frequency of 32 kHz. The video decoder
used for the video signals is not appropriate for these signals since it can only handle 15 kHz signals. This
signal has therefore to be internally redirected, this is done in theSource selectionmenu by selectingData on
BNC’sinstead ofComponent videoand by selectingPr/Y/Pbin the advanced settings of theImage filemenu.
3.4 Composite Video Input
Input specifications
The Composite video input section is made of 1 BNC input terminal. Connect Composite video signals from a VCR, OFF air signal
decoder, etc..
1.0 Vpp ± 3dB
75Ωterminated
No loop through
R/PRG/YB/PBHs/CsVsVIDEO
SDI
INSDI
OUTS-VIDEO
R.C.DVI ANALOG RGB RS 232 C
Image 3-7
Composite video indication
1. data or video
24R5976697 CINEVERSUM™ 110 12/05/2004 
						

							3. Connections
How to select a Composite Video Input ?
1. Press3on the RCU
Note:Another way for selecting this input is viaSourceon the local keypad or via the Menu.
The projector allows the input of more composite video signals (up to 7 composite video signals) when using
the 5 cable input in extended configuration. Press 3 to browse through the possible video sources.
3.5 S-Video input
Input specification
R/PRG/YB/PBHs/CsVsVIDEO
SDI
INSDI
OUTS-VIDEO
R.C.DVI ANALOG RGB RS 232 C
Image 3-8
S-Video indication
Pin configuration 4 pin connector
4
31
2
Image 3-9
For S-VideoFor Video
pin 1 : earth (ground) luminance pin 1 : earth (ground) video Y
pin 2 : earth (ground) chrominance pin 2 : earth (ground) video C
pin 3 : luminance signal (Y) 1Vpp ±3dBpin 3 : video Y signal
pin 4 : chrominance signal (C) 300mVpp pin 4 : video C signal
Chrominance
The color component of a video signal that includes information about tint and saturation.
Luminance
The component of a video signal that includes information about its brightness.
Which signal can be connected ?
Standard S-Video (S-VHS) with separate Y (luma) and C (chroma) signals.
InextendedmodealsoCompositevideocanbeconnectedtotheS-Videoplug.
R5976697 CINEVERSUM™ 110 12/05/200425 
						

							3. Connections
How to select the S-Video input ?
1. Press4on the RCU
Note:Another way for selecting this input is viaSourceon the local keypad or via the Menu.
The projector allows the input of more S-Video signals (up to 3 S-Video signals) via the S-Video extended
configuration.
3.6 Digital Visual Interface (DVI) input
DVI
Digital Visual Interface is a display interface developed in response to the proliferation of digital flat panel displays.
The digital video connectivity standard that was developed by DDWG (Digital Display Work Group). This connection
standard offers two different connectors: one with 24 pins that handles digital video signals only, and one with 29 pins
that handles both digital and analog video. This standard uses TMDS (Transition Minimized Differential Signal) from
Silicon Image and DDC (Display Data Channel) from VESA (Video Electronics Standards Association).
DVI can be single or dual link.
Input specifications
Single link DVI
Differential input voltage: 200 mV - 800 mV
R/PRG/YB/PBHs/CsVsVIDEO
SDI
INSDI
OUTS-VIDEO
R.C.DVI ANALOG RGB RS 232 C
Image 3-10
DVI indication. DVI-I type connector analog link (4 pins at the right side of the connector) not supported.
Pin assignment for the DVI connector.
Pin 1
TMDS DATA2-Pin 13
TMDS DATA3+
Pin 2
TMDS DATA2+Pin14 +5Power
Pin 3
TMDS DATA2/4 ShieldPin 15
Ground (for +5V)
Pin 4
TMDS DATA4-Pin 16 Hot Plug Detect
Pin 5
TMDS DATA4+Pin 17
TMDS DATA0-
Pin 6
DDC ClockPin 18
TMDS DATA0+
Pin 7
DDC DataPin 19
TMDS DATA0/5 Shield
Pin 8 Not connected Pin 20
TMDS DATA5-
Pin 9
TMDS DATA1-Pin 21
TMDS DATA5+
Pin 10
TMDS DATA1+Pin 22
TMDS Clock Shield
Pin 11
TMDS DATA1/3 ShieldPin 23
TMDS Clock+
Pin 12
TMDS DATA3-Pin 24
TMDS Clock-
26
R5976697 CINEVERSUM™ 110 12/05/2004