Barco Projector Cineversum 110 Quickstart Manual
Have a look at the manual Barco Projector Cineversum 110 Quickstart Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 183 Barco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
13. Display Setup Image 13-10 Status bar position This is useful in applications where the bottom image content is not displayed (e.g. due to blanking). How to center the menu ? 1. PressMENUto activate the menu bar. 2. Press→to select theDisplay setupitem. (image 13-11) 3. Press↓to pull down theDisplay setupmenu. 4. Use↑or↓to selectStatus bar position. 5. PressENTER. 6. Use↑or↓to position the status bar Image 13-11 13.7 Sliderbox position What can be done ? The sliderbox can be displayed anywhere on the screen. The exact location can be set in sliderbox menu due to the coarse and fine adjustment. How to reposition the sliderbox? 1. PressMENUto activate the menu bar. 2. Press→to select theDisplay setupitem. (image 13-12) 3. Press↓to pull down theDisplay setupmenu. 4. Use↑or↓to selectSliderbox position. 5. PressENTERto confirm. A sliderbox is displayed. Use the 4 arrow keys to move the box to the desired position. The X and Y coordinate will change simultaneously while moving the box. (image 13-13) 6. Quit withBACK. R5976697 CINEVERSUM™ 110 12/05/2004 117
13. Display Setup Image 13-12 Sliderbox position X position : 619 Y position : 618 Press for fine adjustment Image 13-13 There is a coarse and a fine adjustment of the position, use ENTER (when sliderbox is displayed) to switch between the two. 13.8 Auto Image Setup What can be done ? Auto image allows to detect automatically the characteristics of the source (total pixels per line,...) and uses this information to adapt the image to the DLP panels. Auto image can adapt the image based on following data : • Total pixels per line and total lines • Start pixel and start line • Phase • Contrast/brightness levels Auto image works only for data signals. How to set up Auto Image? 1. PressMENUto activate the menu bar. 2. Press→to select theDisplay setupitem. (image 13-14) 3. Press↓to pull down theDisplay setupmenu. 4. Use↑or↓to selectAuto Image setup. 5. PressENTERto confirm. A dialog box is displayed. (image 13-15) 6. Use the arrow keys to select the desired item and pressENTERto enable or disable that item. 118 R5976697 CINEVERSUM™ 110 12/05/2004
13. Display Setup Image 13-14 Autoimage setup Total pixels/lines Start pixel/line Phase Contrast/brightness Image 13-15 How to perform Auto Image ? 1. pressAuto Imageon the RCU A text box showing a progress bar is displayed. During the AUTO IMAGE measuring process the data source disappears temporarily (logo is displayed if back- ground is set to logo) Autoimage setup Total pixels/lines Start pixel/line Phase Contrast/brightness Image 13-16 R5976697 CINEVERSUM™ 110 12/05/2004119
13. Display Setup 120R5976697 CINEVERSUM™ 110 12/05/2004
14. Installation menu 14. INSTALLATION MENU Overview • Lens adjustments • Projector address • Orientation • Language • Quick access keys • RS232 baudrate • Automatic startup • Security 14.1 Lens adjustments What can be done ? Motorized lenses can be adjusted in the installation menuor via the dedicated keys on the remote (see chapter “Getting Started”, “Quick lens adjustment”). The following parameters can be adjusted: •Zoom • Focus • Shift (also for non motorized lenses) How to Zoom/focus or shift ? 1. PressMENUto activate the menu bar. 2. Press→to select theInstallation. (image 14-1) 3. Press↓to pull down theInstallationmenu. 4. Use↑or↓to selectLens adjustment. 5. PressENTERto start zoom/focus adjustment. A text box appears on the screen. (image 14-2) ↑or↓ Lens zoom ←or→ Lens focus ENTER to switch the cursor key between zoom/focus and vertical/horizontal shift. Logo to switch the image between active source or test pattern 6. PressENTERto switch to the shift mode. See image 14-3. ←or→ Horizontal shift ↑or↓ Vertical shift ENTER to switch the cursor key between vertical/horizontal shift and zoom/focus Logo to switch the image between active source or test pattern R5976697 CINEVERSUM™ 110 12/05/2004121
14. Installation menu Image 14-1 Lens adjustment Use ↑ and ↓ for zoom Use ← and → for focus Press for SHIFT mode Press or for test pattern Image 14-2 Lens adjustment Use ↑ and ↓ for vertical shift Use ← and → for horizontal shift Press for ZOOM/FOCUS Press or for test pattern Image 14-3 14.2 Projector address What can be done ? In some cases the projector address must be changed, for example if an unique RCU is used to control 2 or more projectors in a room. The projector address setting on the projector must match the setting on the RCU. What can be changed ? Within the ’Change Projector Address’ menu, the following items can be changed • Projector address: address defined by the user. Can be set between 0 and 255 when controlled via RS232 and between 0 and 9whencontrolledviatheRCU • Common address : address may be 0 or 1 How to change the projector’s address ? 1. PressMENUto activate the menu bar. 2. Press→to select theInstallation. (image 14-4) 3. Press↓to pull down theInstallationmenu. 4. Use↑or↓to selectProjector address. 5. PressENTERto confirm . A dialog box appears on the screen. Projector address is selected. (image 14-5) 6. PressENTERto go to the edit mode. The most right digit will be selected. Use the left arrow key to jump to the other digits. (image 14-6) 7. Enter an address between 0 and 255 with the digit keys on the RCU and pressENTERto activate. 122 R5976697 CINEVERSUM™ 110 12/05/2004
14. Installation menu Image 14-4 Projector addresses Projector address Common RC5 address5 1 Image 14-5 Projector addresses Projector address Common RC5 address 1005 Image 14-6 How to change the common address ? 1. PressMENUto activate the menu bar. 2. Press→to select theInstallation. (image 14-7) 3. Press↓to pull downtheInstallationmenu 4. Use↑or↓to selectProjector address 5. PressENTER A dialog box appears on the screen. Use the↑to scroll to Common RC5 address. (image 14-8) 6. PressENTERto go to the edit mode. The digit will be selected. (image 14-9) 7. Enter the common address, 0 or 1. Image 14-7 Projector addresses Projector address Common RC5 address 1 5 Image 14-8 Projector addresses Projector address Common RC5 address5 1 Image 14-9 R5976697 CINEVERSUM™ 110 12/05/2004123
14. Installation menu 14.3 Orientation Projector orientations Depending on how the projector is oriented, the projector’s internal settings have to be adapted. See also Chapter “Installation”, “Orientation”. How to change the orientation ? 1. PressMENUto activate the menu bar. 2. Press→to select theInstallationitem. (image 14-10) 3. Press↓to pull down theInstallationmenu. 4. Use↑or↓to selectOrientation. 5. Press→to pull down the menu. 6. Use↓or↑to select the desired orientation. 7. PressENTERto confirm. The projection is adapted and a white bullet shows the active configuration. Image 14-10 14.4 Language List of languages The list of selectable languages depends on the software of the projector. Standard available languages: • English • French •German • Spanish How to change the Language ? 1. PressMENUto activate the menu bar. 2. Press→to select theInstallationitem. (image 14-11) 3. Press↓to pull down theInstallationmenu. 4. Use↑or↓to selectLanguage. 5. Press→to pull down the menu. 6. Use↓or↑to select the desired language. 7. PressENTERto confirm. The language is adapted and a white bullet shows the active configuration. 124 R5976697 CINEVERSUM™ 110 12/05/2004
14. Installation menu Image 14-11 14.5 Quick access keys What can be done ? The 3 function keys on top of the RCU (F1, F2 and F3) can be associated with a particular item in one of the menus. Each function which is not password protected can be associated to a function key. How to get an overview of the quick access keys ? 1. PressMENUto activate the menu bar. 2. Press→to select theInstallation. (image 14-12) 3. Press↓to pull down theInstallationmenu. 4. Use↑or↓to selectQuick access keys. 5. PressENTER. The quick access keys overview text box appears on the screen. (image 14-13) Default factory pre-programmed functionsare : color, brightness and contrast. Image 14-12 Quick access keys overview F1 : color F2 : brightness F3 : contrast Image 14-13 How to program the quick access keys ? 1. Scroll through the menu bar to the desired menu item. 2. Push the desired function key for 3 seconds. The menu item is stored behind the quick access key. The messageQuick Access key storedwill be displayed. R5976697 CINEVERSUM™ 110 12/05/2004 125
14. Installation menu 14.6 RS232 baudrate How to change the baudrate? 1. PressMENUto activate the menu bar. 2. Press→to select theInstallationitem. (image 14-14) 3. Press↓to pull down theInstallationmenu. 4. Use↑or↓to selectRS232 baudrate 5. Press→to pull down the menu. 6. Use↓or↑to select the desired baudrate. 7. PressENTERto confirm. Image 14-14 14.7 Automatic startup What can be done ? The automatic startup allows immediate restart of the projector after a power failure (breakdown), i.e. without passing through the standby state. The projector restarts at power resume and recovers the previous settings (previous source,...). This function can be disabled if undesired or inadequate for safety reasons, etc. CAUTION:If the Automatic startup function is enabled one must be aware of the fact that it involves safety precautions Make sure that the projector (or the operators!) will not be affected by altered environmental conditions when restarting at power resume. How to enable/disable the Automatic startup? 1. PressMENUto activate the menu bar. 2. Press→to select theInstallationitem. (image 14-15) 3. Press↓to pull down theInstallationmenu. 4. Use↑or↓to selectAutomatic startup. 5. Press→to pull down the menu. 6. Use↓or↑to enable/disable the automatic startup. OnAutomatic startup enabled OffAutomatic startup disabled 7. PressENTERto confirm. 126 R5976697 CINEVERSUM™ 110 12/05/2004