Barco Projector Cineversum 110 Quickstart Manual

							10. Signal menu
Image 10-2* Video may be Composite video/ S-Video / SDI
• dark arrow : fade in/out effect possible
• dotted arrow : undetermined case, fade in/out effect may take place or not
• striked out arrow : fade effect impossible
The switching effects are only possible in the full screen mode
10.3 Background
Purpose
If there is no signal connected to the projector, the background will be a logo, a black or a blue screen depending on thebackground
settings.
How to change the background ?
1. PressMENUto activate the Tool bar.
2. Press→to select theSignalitem. (image 10-3)
3. Press↓to pull down theSignalmenu.
4. Use↑or↓to selectBackground.
5. Press→to pull down the menu.
R5976697 CINEVERSUM™ 110 12/05/2004
97 
						

							10. Signal menu
6. Use↑or↓to select the desired background.
7. PressENTER.
Image 10-3
The logo display is only possible in the full screen mode, a logo can thus not be displayed (rescaled) in a
window in the PiP mode.
When there is no signal connected, the projector will also start its standby timer countdown (if enabled) and
shuts down after the predetermined time.
98R5976697 CINEVERSUM™ 110 12/05/2004 
						

							11. Lamps Menu
11. LAMPS MENU
Overview
• Overview of the Lamps menu
• Runtimes
• Mode
• Economic ON/OFF
• Runtime warning
11.1 Overview of the Lamps menu
Overview
• Runtimes...
• Mode
- Single...
- Dual...
• Economic
• Runtime warning
11.2 Runtimes
How to display the lamp runtimes ?
1. PressMENUto activate the menu bar.
2. Press→to select theLampitem. (image 11-1)
3. Press↓to pull down theLampsmenu.
4. Use↑or↓to selectRuntimes.
5. PressENTER.
A text box is displayed. (image 11-2)
Image 11-1
Runtime
Lamp 1 hrs
Lamp 2 hrs
Projector
hrs 500
531
2005
Image 11-2
Runtime text box: yellow indicator means the lamp is working
R5976697 CINEVERSUM™ 110 12/05/200499 
						

							11. Lamps Menu
11.3 Mode
Single lamp mode
The projector will always switch to the lamp with the shortest runtime when the difference between the runtimes of lamp 1 and lamp
2 reaches100 hours, switching from one lamp to another happens only at switching on of the projector and not during operation.
When the lamp fails or reaches its maximum runtime the projector switches automatically to the other lamp without interrupting the
projection. The failure is logged and the lamp will never be initialized in the future.
Image 11-3
Single mode operation: switching principle
Dual lamp mode
Both lamps are working.
When one lamp fails, the projector continues the projection using the remaining lamp.
How to select the lamp mode ?
1. PressMENUto activate the menu bar.
2. Press→to select theLampsitem. (image 11-4)
3. Press↓to pull down theLampsmenu.
4. Use↑or↓to selectMode.
5. Press→to pull down the menu.
6. Use↑or↓to select the desired mode.
Single Only one lamp is ignited.
Dual Both lamps are ignited.
7. PressENTERto confirm.
A bullet shows the active mode.
100
R5976697 CINEVERSUM™ 110 12/05/2004 
						

							11. Lamps Menu
Image 11-4
When switching from the dual mode to the single mode the lamp with the longest runtime is switched off.
If the runtimes are equal (if the projector has always been operated in dual mode) then lamp 1 is switched out.
When switching to single mode, returning to the dual mode will not be possible in the first 60 seconds,Dual
in the menu is greyed out and LED3 is flickering, thereby preventing hot restrike which may damage the lamp.
11.4 Economic ON/OFF
What can be done?
The lamp power can be reduced to save the lamp. When using the reduced lamp power, the lifetime will be adapted accordingly.
How to switch to an economic mode ?
1. PressMENUto activate the menu bar.
2. Press→to select theLampsitem. (image 11-5)
3. Press↓to pull down theLampsmenu.
4. Use↑or↓to selectEconomic.
5. Press→to select theOn or Offitem.
OnEconomic mode is switched on
Off Economic mode is switched off
6. PressENTERto confirm.
Image 11-5
11.5 Runtime warning
What can be done ?
When the lamp has reached a certain predetermined runtime, a warningmessage will be displayed on the screen. The lamp runtime
warning can be set in a range from 30 to 200 hours. The runtime warning is displayed by default at 30 hours before end of lamp
lifetime.
How to set the lamp runtime warning?
1. PressMENUto activate the menu bar.
2. Press→toselect theLampitem. (image 11-6)
3. Press↓to pull down theLampsmenu.
R5976697 CINEVERSUM™ 110 12/05/2004
101 
						

							11. Lamps Menu
4. Use↑or↓to selectRuntime warning.
5. PressENTERto confirm.
A dialog box is displayed. (image 11-7)
6. PressENTERto activate the input field.
7. Use←or→to change the runtime warning setting.
Or,
enter the desired value with the digit keys on the remote control.
8. PressBackto return.
Image 11-6
Lamp runtime warning
hrs before end of lamp lifetime
30
Image 11-7
WARNING:Lamp replacement should be done by a Barco authorized technician.
102R5976697 CINEVERSUM™ 110 12/05/2004 
						

							12. Image Files Menu
12. IMAGE FILES MENU
Overview
• Overview of the Image Files Menu
• Introduction to image files
• Load file
• Auto Image
• Edit file
• Rename file
• Copy
• Delete
12.1 Overview of the Image Files Menu
Overview
• Load
•Filesort
-name
- index
•Autoimage
- Limited scan
- Full scan
• Edit...
• Rename...
• Copy...
• Delete...
12.2 Introduction to image files
Introduction
An image file contains the main characteristics of a source (number of active lines,...). The projector’s memory contains a list of files
corresponding to the most common sources, these are the standard files (file extension= *.s). When a new source corresponds to
one of these files, a custom file (file extension=*.C) is created and saved for future use.
The maximum number of custom files that can be created is 99, the four last files are systematically overwritten.
When there is a little difference, the file can also be loaded and then edited until the source specs are reached.
Possible file manipulations
The possible file manipulations are :
• Load : installation of a file for a new source
• Edit : editing a loaded file to match the source specifications
• Rename : renaming a file
• Copy: copyingafiletoanewfile
• Delete : deleting an existing file
12.3 Load file
Howtoloadafile?
1. PressMENUto activate the menu bar.
2. Press→to select theImage filesitem. (image 12-1)
3. Press↓to pull down theImage filesmenu.
R5976697 CINEVERSUM™ 110 12/05/2004
103 
						

							12. Image Files Menu
4. Use↑or↓to selectLoad.
5. PressENTER.
A dialog box is displayed. (image 12-2)
6. Use↑or↓to select the desired file.
Tip:For more info about the available image files and thespecifications, see Chapter Standard Image Files.
7. PressENTERto confirm.
The file will be loaded and the image is adapted accordingly.
Image 12-1
Load file
Video625.c01
Video625.c02
Video625.s00
Image 12-2
load file dialogbox in case of a video source
InPiPmode,thefileswhichmaybeloadedwillbeofthedatatypeiftheactivewindowisadatawindow,or
they will be of the video type if the active window is a video window.
What to do if the image is not perfect ?
If the displayed image is not correct after AutoImage or after selecting the best fitting file, go to the Edit menu, select the active file
and change the settings.
12.4 Auto Image
What can be done ?
Auto Image creates the best suited image file for the connected source.
It calculates/measures several source parameters :
• Total pixels per line
•Startpixel
• Phase
• Contrast/Brightness levels
Auto Image works only for data images.
104R5976697 CINEVERSUM™ 110 12/05/2004 
						

							12. Image Files Menu
The measure of the total number of pixels per line can be done through 2 methods
• Limited scan: a windowing is used to allow fast tracking.
The operation takes about 20 seconds (depending on file)
• Full scan: tracking is done over the full range.
The operation takes about 1.5 minutes (depending on file)
How to launch Auto Image?
1. PressMENUto activate the menubar (image 12-3)
2. Press→to select theImage filesitem
3. Press↓to pull down theImage filesmenu
4. Use↑or↓to selectAuto Image
5. Press→to open the menu
6. Use↑or↓to select the desired file scan method
7. PressENTER
A text box showing a progress bar is displayed. (image 12-4)
Tip:Press theCancelbutton to cancel the operation.
Image 12-3
Autoimage
Total pixels/lines
Start pixel/line
Phase
Contrast/brightness
Image 12-4
The Auto Image setup in theDisplay setupmenu affect only Auto Image if it is launched via the RCU key or at
automatic file creation.
Launching Auto Image via the menu involves complete checking of all parameters.
Auto Image can also be launched via the RCU with the dedicated AutoImage key.
R5976697 CINEVERSUM™ 110 12/05/2004105 
						

							12. Image Files Menu
12.5 Edit file
Overview
• Editing a file
• Correct file parameters
• Advanced video settings
• Advanced Data settings
12.5.1 Editing a file
What can be done with the Edit file menu ?
The Edit file menu makes it possible to adapt the settings of the file according to the real settings of the connected source. Consult
the source specifications before entering the data.
How to edit a file ?
1. PressMENUto activate the menu bar.
2. Press→to select theImage filesitem. (image 12-5)
3. Press↓to pull down theImage filesmenu.
4. Use↑or↓to selectEdit.
5. PressENTER.
A dialog box is displayed. (image 12-6)
6. Use↑or↓to select the desired file.
Note:If in PiP mode the cursor is placed by default on the active file which has the focus.
7. PressENTERto confirm.
A dialog box is displayed with the selected source settings. (image 12-7)
8. Use←or→to edit and change the values.
Note:greyed out fields can not be updated (total pixels).
9. PressENTERto confirm.
Image 12-5
106R5976697 CINEVERSUM™ 110 12/05/2004