Barco Hdx Series Installation Manual

12. Alignment
12.14 Scenergix
R5905032 HDX SERIES 23/11/2011217 

12. Alignment
12.14.1 Introduction
Why ScenergiX ?
When working in a multichannel setup the HDX and its Soft Edgepossibilities enable an image blending that gives the appearance
of a single view, thus achieving realistic immersion for the majority of wide screen applications.
ScenergiX is limited to half the resolution of the projector.
Image 12-69
Why Soft Edge?
What is the Basic Principal of ScenergiX ?
The principle of edge blending is achieved by linear modulation of thelight output in the overlap...

12. Alignment
12.14.2 Preparations
ScenergiX Preparations
To ensure proper ScenergiX adjustment, be sure that the following adjustments are done perfectly on all projectors:
• Convergence
• Geometry
• Color Matching (Color Temperature, Color Standard, Input Balance, Gamma)
R5905032 HDX SERIES 23/11/2011
219 

12. Alignment
12.14.3 Scenergix activation
How to activate
1. PressMenuto activate the menus and selectAlignment→Scenergix.
Image 12-71
Main menu, alignment
Image 12-72
Alignment, Scenergix
2. PressENTERto select.
TheScenergixmenu opens.
Image 12-73
Scenergix, status
3. Use the▲or▼key to select Status and pressENTERto toggle between[On]and[Off]
[On] : Scenergix is activated.
[Off] : Scenergix is deactivated
220
R5905032 HDX SERIES 23/11/2011 

12. Alignment
12.14.4 Scenergix pattern
What can be done?
To make the Scenergix adjustment more easy, an internal pattern can be displayed.
How to select
1. PressMenuto activate the menus and selectAlignment→Scenergix→Scenergix Pattern.
Image 12-74
Main menu, alignment
Image 12-75
Alignment, Scenergix
Image 12-76
Scenergix, pattern activation
2. PressENTERto toggle between[On]or[Off].
[On] : Internal scenergix pattern is displayed.
[Off] : no scenergix pattern is displayed.
1050 90 130170 210...

12. Alignment
12.14.5 Scenergix adjustment lines
What can be done?
Border lines for the blending areas can be displayed while adjusting the white and black level.
Adjustment lines can be activated whenScenergix patternis [On].
How to display
1. PressMenuto activate the menus and selectAlignment→Scenergix→Adjust lines.
Image 12-78
Main menu, alignment
Image 12-79
Alignment, Scenergix
Image 12-80
2. PressENTERto toggle between[On]and[Off].
222
R5905032 HDX SERIES 23/11/2011 

12. Alignment
12.14.6 White level adjustment (blending area)
How to set
1. PressMenuto activate the menus and selectAlignment→Scenergix→White level.
Image 12-81
Main menu, alignment
Image 12-82
Alignment, Scenergix
Image 12-83
Scenergix, white level
2. PressENTERto select theWhite leveladjustments.
The White level position menu opens.
When Adjustment lines is[On], the different areas are displayed on the screen.
Image 12-84
White level position
3. Use the▲or▼key to select one of the four size adjustments...

12. Alignment
Image 12-85
Width selections
4. Setfirst the width for thefirst projector and repeat for the second one.
Image 12-86
Width set up for projector1
224R5905032 HDX SERIES 23/11/2011 

12. Alignment
Image 12-87
Width set up for projector 2
To eliminate all blending settings, selectResetand press ENTER.
R5905032 HDX SERIES 23/11/2011225 

12. Alignment
12.14.7 Black level adjustment
Why black level adjustment
For dark images, the overlap zone will be brighter then the rest of the images. Typically for DLP projectors, next to the overlap
zone, a brighter area is recognized. This area is known as a DLP leakage area. This area must also be exclude for the black level
adjustment. Therefore we can rise the black level of the remaining image (excluding the overlap zone and the DLP leakage area).
First, the width of the leakage area must be set....