Barco Hdx Series Installation Manual

11. Lamp
11.9 LPS power
What is indicated ?
The current LPS power in watt is indicated as information.
Image 11-24
LPS power
R5905032 HDX SERIES 23/11/2011187 

11. Lamp
11.10 Lamp identification
About
The lamp identification menu gives an overview of the most important parameters of the used lamp.
These parameters are:
• Serial number of the lamp
• Article number of the lamp
• Run time sincefirst start up of the lamp
• Remaining run time for a safe operation of the lamp
• Number of strikes since thefirst start up of the lamp
• Software version
These parameters are useful in case of a service request.
How to display
1. PressMenuto activate the menus and...

11. Lamp
11.11Z-axisadjustment
What can be done?
TheZ-Axismenu item gives the current light output of the projector (in percentage). This light output indication can be used to
readjust the lamp position in the lamp casing (also called Z-axis adjustment of the lamp). With higher run times, the light output
of the lamp will decrease, which results in a lower light output on the screen. This light output decrease can be compensated by
readjusting the position of the lamp. This realignment has to be done by...

11. Lamp
190R5905032 HDX SERIES 23/11/2011 

12. Alignment
12. ALIGNMENT
Overview
• Alignment menu overview
• Orientation
• Lens adjustment, zoom - focus
• Lens adjustment, shift
• Lens adjustment, mid position
• Home lens at startup
• Calibrate lens
• Warping
• Blanking adjustment
• Contrast-Intensity
• Gamma
• Internal patterns
• Color space
• Scenergix
R5905032 HDX SERIES 23/11/2011
191 

12. Alignment
12.1 Alignment menu overview
Overview table
Level 1 Level 2 Level 3
Alignment
Orientation Front / Table
Front / Ceiling
Rear / Table
Rear / Ceiling
Auto Front
Auto Rear
Lens
Zoom / Focus
Shift
Mid Position
Home lens at startup
Calibrate lens
Warping
Status
Rotation
Keystone
Pin/Barrel
4 corners
Warpfile service
Reset
Blanking Top
Bottom
Left
Right
Contrast/Intensity Contrast enhancement
Intensity
Gamma
Internal Patterns
Color Space Status
Projector
EBU
SMPTE
Custom
ScenergiX Status
White...

12. Alignment
12.2 Orientation
What can be done?
The way of physical installation of the projector can be defined to the projector.
The following installation are possible:
• front/table
• front/ceiling
• rear/table
• rear/ceiling
• auto front : automatic front, projector detects itself if it is ceiling or table mounted and projects always a readable image.
• auto rear : automatic rear, projector detects itself if it is ceiling or table mounted and projects always a readable image.
How to set the correct...

12. Alignment
12.3 Lens adjustment, zoom - focus
Zoom/Focus adjustment
1. PressMenuto activate the menus and selectAlignment→Lens.
Image 12-4
Main menu, alignment
Image 12-5
Alignment, lens
2. Use the▲or▼key to selectzoom/focusand pressENTERto activate.
Image 12-6
Lens, Zoom/Focus
3. Use the▲or▼key to zoom the lens.
Use the◄or►key to focus the lens.
PressENTERto switch to Lens shift adjustment.
Image 12-7
Zoom/Focus adjustment
194R5905032 HDX SERIES 23/11/2011 

12. Alignment
12.4 Lens adjustment, shift
How to shift lens
1. PressMenuto activate the menus and selectAlignment→Lens.
Image 12-8
Main menu, alignment
Image 12-9
Alignment, lens
2. Use the▲or▼key to selectShiftand pressENTERto activate.
Image 12-10
Lens, shift
3. Use the▲or▼key to shift the lens in vertical direction.
Use the◄or►key to shift the lens in horizontal direction.
PressENTERto switch to Zoom/Focus adjustment.
Image 12-11
Shift adjustment
R5905032 HDX SERIES 23/11/2011195 

12. Alignment
12.5 Lens adjustment, mid position
Howtoreturntomidposition
1. PressMenuto activate the menus and selectAlignment→Lens.
Image 12-12
Main menu, alignment
Image 12-13
Alignment, lens
2. Use the▲or▼key to selectMid Positionand pressENTERto activate.
Image 12-14
Lens, mid position
Lens will be shifted horizontally and vertically to its mid position.
196
R5905032 HDX SERIES 23/11/2011