Barco Hdx Series Installation Manual

13. Projector Control
Image 13-57
Wireless default gateway, input
4. Use the▲or▼key to change the selected character.
Use the◄or►key to select another character.
Note:Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way,
the next character will be selected automatically.
R5905032 HDX SERIES 23/11/2011
257 

13. Projector Control
13.6 IR Control switching
What can be done ?
Each IR receiver inside the projector can be activated or deactivated. When an IR receiver is deactivated, no IR signal send to this
IR receiver will be processed.
How to activate or deactivate
1. PressMenuto activate the menus and selectProjector Control→IR control.
Image 13-58
Main menu, projector control
Image 13-59
Projector control, IR control
Image 13-60
IR control
2. Use the▲or▼key to select the desired IR control and pressENTERto...

13. Projector Control
13.7 DMX
Overview
• DMX address
• DMX universe
• DMX mode
•Art-NetDMX
• Front XLR output voltage control
•Monitor
About the ways to control the projector via DMX
With a standard DMX cable equipped with XLR connector DMX signals can be connected to the DMX In port on the communicator
interface. The DMX out can be used to create a chain of DMX devices. One universe can control up to 512 channels.
If you are using a DMX console and other automated lighting products compatible with...

13. Projector Control
13.7.1 DMX address
What should be done ?
Before a projector can execute DMX commands, a unique address, called DMX address, should be given to the projector. This
address can vary from 1 to 512.
How to set the DMX address
1. PressMenuto activate the menus and selectProjector Control→DMX→Address.
Image 13-61
Main menu, projector control
Image 13-62
Projector control, DMX
Image 13-63
DMX, address
2. PressENTERto select.
Image 13-64
DMX address
3. Use the▲or▼key to change the selected...

13. Projector Control
13.7.2 DMX universe
What can be done ?
Depending on the DMX mode, one DMX universe can contain a different number of projectors. E.g. DMX mode = basic, the DMX
universe can contain up to 256 projectors
Universes are only meaningful for Art-Net applications as only there multiple universes can be addressed.
How to set a DMX universe
1. PressMenuto activate the menus and selectProjector Control→DMX→Universe.
Image 13-65
Main menu, projector control
Image 13-66
Projector control, DMX...

13. Projector Control
13.7.3 DMX mode
What can be done ?
3 modes for DMX are available:
• Basic which has currently 2 channels implemented.
• Extended which has currently 10 channels implemented
• Full which has currently 9 channels implemented and a 10th free channel.
Depending on the DMX application the correct mode has to be selected.
How to set the mode
1. PressMenuto activate the menus and selectProjector Control→DMX→Universe.
Image 13-69
Main menu, projector control
Image 13-70
Projector control,...

13. Projector Control
13.7.4 Art-Net DMX
What can be done ?
DMX can be sent via Ethernet to the projector. This function can be enabled or disabled.
Art-Net DMX [On] : DMX via Ethernet is enabled.
Art-Net DMX [Off] : DMX via Ethernet is disabled.
How to toggle
1. PressMenuto activate the menus and selectProjector Control→DMX→Art-Net DMX.
Image 13-72
Main menu, projector control
Image 13-73
Projector control, DMX
Image 13-74
DMX Art-Net activation
2. PressENTERto toggle between[On]and[Off].
R5905032 HDX...

13. Projector Control
13.7.5 Front XLR output voltage control
What can be done ?
The output voltage on the front XLR connector can be enabled or disabled.
The output voltage level can be set to 0V, 9V, 12V or 24V.
DMX Art-Net can also enable the output voltage on the front XLR connector. To avoid that per accident a voltage is activated via
DMX Art-Net, set level to 0 V
How to enable or disable
1. PressMenuto activate the menus and selectProjector Control→DMX→Output voltage enable.
Image 13-75
Main menu,...

13. Projector Control
Image 13-78
Main menu, projector control
Image 13-79
Projector control, DMX
Image 13-80
Front XLR output voltage level
2. PressENTERto toggle between [0 Volt], [9 Volt], [12 Volt] and [24 Volt].
R5905032 HDX SERIES 23/11/2011
265 

13. Projector Control
13.7.6 Monitor
What can be done ?
If a DMX device is connected, the settings per channel can be displayed in an on screen menu.
How to start up the monitoring
1. PressMenuto activate the menus and selectProjector Control→DMX→Monitor.
Image 13-81
Main menu, projector control
Image 13-82
Projector control, DMX
Image 13-83
DMX monitor
2. PressENTERto open the overview list.
266
R5905032 HDX SERIES 23/11/2011