Avaya Partner Advanced Communications System 1600 Dsl Module User Guide

Avaya, Inc. - 70 - PARTNER ACS 1600 DSL module User Guide
Y. Delete a DHCP Assignment Entry
Deletes an assigned IP address from the Display DHCP
Server Assigned Addresses command.  Type the IP
address to delete, and then press ENTER.
N. Configure
NAT
Displays the NAT Configuration Menu, which contains the
following commands to configure the Network Address
Translation (NAT).
NAT allows you to use one IP address of every workstation in
your company.  This hides your internal Intranet addresses.
You must...

Avaya, Inc. - 71 - PARTNER ACS 1600 DSL module User Guide
the number connections.  Since the range that you assign
must be outside the range of the programs in use, do not set
port ranges under 5,000.
Type the Low End of NAT Port Range value, the High End of
NAT Port Range value, and then press ENTER.
N. Configure NAT Local Server Entry
Makes local servers visible to the Internet.
Type the following information, and then press ENTER:
•  Local Server entry number
•  NAT Local Server Translated IP address...

Avaya, Inc. - 72 - PARTNER ACS 1600 DSL module User Guide
C. Display NAT Connection Table
Displays the following information about the NAT connections:
• TCP - Ethernet MAC address of the device.
• out_port
• pkts - out, in
• state
• idle
D. Display NAT Connection Details
Displays the following information about the NAT connections:
• Outside port number of connection
• Foreign IP
• Local IP
• # Ports - outside, inside, foreign
• Outgoing packets/# bytes
• Incoming packets/# bytes
• Type - TCP or UDP
•...

Avaya, Inc. - 73 - PARTNER ACS 1600 DSL module User Guide
Y. Delete NAT Local Server Entry
Deletes an NAT Local Server entry from the Display NAT
Statistics, Display NAT Connection Table and Display
NAT Connection Details commands.  Type the Local Server
entry to delete, and then press ENTER.
T. Derived
Timing
Displays the Derived Timing submenu, which contains the
following commands to enable/disable derived timing and
display debugging messages.
1. Enable/Disable Derived Timing
Enables and disables...

Avaya, Inc. - 74 - PARTNER ACS 1600 DSL module User Guide
3. Enable/Disable **Local Clock ONLY** Derived
Timing Debug Messages
Displays the Derived Timing Debug submenu, which
contains the following commands to enable/disable
only local clock derived timing debugging messages.
1. Enable
2. Disable
Select your choice.
Select your choice.
Z. Diagnostics
Menu
Displays the Diagnostics submenu, which contains the
following command.
P. POTS Diagnostics
Displays the POTS Diagnostics submenu, which contains the...

Avaya, Inc. - 75 - PARTNER ACS 1600 DSL module User Guide
C. Command
Line Interface
For future implementation.
Displays the command line interface, which supports the
following syntax and commands.
Command line syntax
The command syntax is:
COMMAND  (optional parameters)
For example:
Set wan ip address 192.3.4.5 255.255.255.02001
The required parameters are the ip address
 and the netmask .
The optional parameters are the slot (2), interface(0),
port(0) and connection(2).
The command and its parameters...

Avaya, Inc. - 76 - PARTNER ACS 1600 DSL module User Guide
DLCI number and encapsulation type to RFC1490 or
RFC1483. .  If you do not enter any optional
parameters, it finds the first available slot, interface,
port and connection.
set nat  (slot) (interface) (port) – sets
NAT on or off. .  If you do not enter any optional
parameters, it finds the first available slot, interface and
port.
set dns server address  -
sets the DNS server IP address.
set system defaults – sets the system to the default...

Avaya, Inc. - 77 - PARTNER ACS 1600 DSL module User Guide
As shown in the equation below, this is equivalent to the
difference in the relative transit time for two packets: the
relative transit time is the difference between a packets RTP
time-stamp and the receivers clock at the time of arrival,
measured in the same units.
If Si is the RTP time-stamp from packet i, and Ri is the time of
arrival in RTP time-stamp units for packet i, then for two
packets i and j, D can be expressed as:
D(ij) = (Rj -Ri)...

Avaya, Inc. - 78 - PARTNER ACS 1600 DSL module User Guide
M. Set Debug Mode
Displays the Debug Mode Selection submenu, which
contains the following commands.
E. ENABLE Debug
D. DISABLE Debug
Select your choice.
E. Configure Echo Cancellation Default Settings
Displays the Echo Cancellation Default Settings
Configuration Menu, which contains the following
commands.
1. Set Echo Cancellation default setting for all ports
Enables and disables echo cancellation globally.
2. Display current Echo Cancellation...

Avaya, Inc. - 79 - PARTNER ACS 1600 DSL module User Guide
M. Manage
MGCP/NCS
Embedded
Client
Displays the MGCP/NCS Management Menu, which contains
the following submenus and commands.
C. Configure MGCP/NCS parameters
Sets the MGCP/NCS parameters.  Type the following
information, and then press ENTER:
•
•• • Default IP address for Notified Entity
•
•• • IP address to use for MGCP signaling (Data)
packets
•
•• • Type of Service (TOS) field value for the IP header
of the outbound signaling packets
•
•• • IP...