ATT Definity Addendum 1 For Ds1, Dmi, Isdn Pri Instructions Manual

ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 27-103
ENHANCED MODE — PROCEDURE: 279, WORD: 1
NETWORK-SPECIFIC FACILITY
1. ISDN Network Service Value:
ISDN NETWORK DEFINITION
2.
3.
4.Parameterized — Binary:
Feature — Service:
Facility Coding Value:
PARAMETERS
5.
6.
7.
8.
9.
10.
11.Parameter 1:
Parameter 2:
Parameter 3:
Parameter 4:
Parameter 5:
Parameter 6:
Parameter 7:
Connected to CC0 ON-LINE
enter command:½
Field 1Figure 7-49. Procedure 279 Word 1: Network Facilities Coding (Generic 2)
Translates...

7-104ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 2
TABLE 7-12. Network Services/Network Features½
NAME
Recom-
mended
NSVParameterized 
(0)
or
Binary (1)
Feature (0)
or
Service (1)
Facility
Coding
Value½
½
½
Caller data80
08½
Out-WATS band33-288
011
Operator handled
3241
05½
Pre-subscribed
CC operator32510
6
SDN3521
11
Long distance service
3531
17
MEGACOM 800 service
n/an/a
n/an/a½
½
½
MEGACOM
354
1
13
In-WATS355
11
4½
½
WATS maximal
subscribed band35611
5
ACCUNET switched
digital services357
11...

ENHANCED MODE — PROCEDURE: 309, WORD: 1
ARS — ROUTE TABLES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.ARS Plan:
Pattern Number:
Preference Number:
Trunk Group:
Facility Restriction Level:
Warning Tone:
Distant Area Code (NPA):
Send 1 For Toll:
Toll Table Index:
Number of Digits Deleted:
Digit Collect (DC) Signal Ignore:
IXC ISDN Network Identifier:
Connectedd to CC0 ON-LINE
enter command:ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 2
7-105½
Fields 1-11
Field 12Figure 7-50. Procedure 309 Word 1: ARS Route...

7-106ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 2
Procedure 309 Word 5: ARS–ISDN BCCOS
This procedure is required for translating ISDN trunk groups into the ARS plan.
NOTE: When translating MEGACOM, SDN, and ACCUNET switched digital service calls, you
must first assign a network specific facility (NSF) index in field 1 of procedure 279, word 1, and
then assign this same index in field 5 of this procedure to all preferences used for these types of½
½
½
½
½
½
calls.
Figure 7-51, Procedure 309 Word...

ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 27-107
Field 5
Specifies the network service that is requested. Refer to table 7-12, Network
Services/Network Features, for the appropriate encode.
NOTE: When translating MEGACOM, SDN, and ACCUNET switched digital
service calls, you must first assign a network specific facility (NSF) index in field
1 of procedure 279, word 1, and then assign this same index in this field to all
patterns used for these types of calls.½
½
½
½
½
½
Field 6
Assigns a BCCOS to...

7-108ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 2
Field 10Specifies either the number (designation) of the interexchange carrier (IXC) or the
ISDN Network Service Identifier for this trunk group. The IXC/ISDN network
identifier enables the switch to provide equal access capability by populating either the
NSF IE or the Transit Network Selection IE. If sending an NSF IE and a particular
IXC vendor number is specified in this field, that entry is included in the NSF IE. If
no IXC vendor number is...

ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 27-109
ENHANCED MODE — PROCEDURE: 321, WORD: 5
AAR — ISDN AND BEARER CAPABILITY COS
1.
2.
3.
4.
5.Pattern Number:
Preference Number:
ISDN Dynamic Trunk Type:
ISDN Network Service Value:
Bearer Capability COS:
Connected to CC0 ON-LINE
enter command:
Figure 7-53. Procedure 321 Word 5: AAR-ISDN and Other Feature Parameters (Generic 2)½
Field 1
Specifies the AAR pattern number. Permitted encodes are numbers within the range of
1 through 640.
Field 2
Specifies...

7-110ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 2
Field 4
Specifies the network service requested. Refer to table 7-12, Network
Services/Network Features, for the appropriate encode.
NOTE: When translating MEGACOM, SDN, and ACCUNET switched digital
service calls, you must first assign a network specific facility (NSF) index in field
1 of procedure 279, word 1, and then assign this same index in this field to all
patterns used for these types of calls.½
½
½
½
½
½
Field 5
Assigns a BCCOS to the...

ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 27-111
Field 2Dash (–), is appropriate for voice terminal and attendant console applications.
If a transmission test line is used, its type should be specified.
Fields 3-18
Assigns digits for the terminating test line and TVS.½
NOTE: Procedure 107, words 2-7, need only be translated whenever ATMS is used.
Procedure 108 Word 1: ISDN Trunk Group TTL Number (Digits)
This procedure is used to assign the terminating test line number (used in test 3 of...

7-112ADMINISTRATION OPTIONS AND REQUIREMENTS — GENERIC 2
Field 1Translates the trunk group that identifies the ISDN terminating test line. The
terminating test line is required for B-channel maintenance testing.½
NOTE: As part of the installation and ISDN-PRI services provisioning, the
terminating test line number assignment must be coordinated with the terminating
switch.
Fields 2-17
Assigns digits for the terminating test line.
NOTE: If B-channel signaling control is used on the D-channel of another...