2012 Na Yamaha Super Tenere Manual

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-102
3 Defective wheel sensor. If the above items were per-
formed and no malfunctions were 
found, connect the ABS ECU 
coupler and rear wheel sensor 
coupler, and then delete the fault 
codes. If fault code No. 16 could 
not be deleted, the rear wheel 
sensor is defective. Replace the 
rear wheel sensor.
TIP
Before deleting the fault codes, 
record all of the fault codes and 
perform the related checks and 
maintenance.
Fault code No. 17 Symptom Missing pulses...

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-103
Fault code No. 18 Symptom Missing pulses detected in the rear wheel sen- sor signal.
Order Item/components and probable  cause Check or maintenance job Reinstatement 
confirmation 
method
1 Installed condition of wheel bearings,  axle, sensor housing, and sensor ro-
tor. Check the components for loose-
ness, distortion, and bends.
Refer to 
“CHECKING THE REAR 
WHEEL ” on page 4-32. 
Set the main 
switch to  “ON” 
and check 
that the ABS 
warning light 
comes on...

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-104
Fault code No. 22 Symptom Start switch signal is not received properly  (start switch circuit or start switch monitor cir-
cuit).
Order Item/components and probable  cause Check or maintenance job Reinstatement 
confirmation 
method
1 Engine startability. Check the electric starting sys- tem.
Refer to “ELECTRIC STARTING 
SYSTEM” on page 8-7. 
Push the start 
switch and 
check that the 
engine starts.
 Set the main 
switch to  “ON” 
and check 
that the ABS...

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-105
Fault code No. 33 Symptom ABS motor is defective. Power is not supplied to the ABS motor.
Order Item/components and probable  cause Check or maintenance job Reinstatement 
confirmation 
method
1 Battery voltage Recharge or replace the battery.
Refer to “CHECKING AND 
CHARGING THE BATTERY ” on 
page 8-132. 
Set the main 
switch to  “ON” 
and check 
that the ABS 
warning light 
comes on for 
2 seconds, 
then goes off.
 Pe rfo r m hy -
draulic unit 
operation test...

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-106
Fault code No. 34 Symptom Hydraulic unit ABS motor is short-circuited.
Order Item/components and probable  cause Check or maintenance job Reinstatement 
confirmation 
method
1 Short circuit in ABS motor relay. Replace the hydraulic unit as- sembly.
Set the main 
switch to  “ON” 
and check 
that the ABS 
warning light 
comes on for 
2 seconds, 
then goes off.
 Pe rfo r m hy -
draulic unit 
operation test 
1 and check 
that the oper-
ation of the 
hydraulic unit...

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-107
WARNING
EWA23P1021
The front brakes will not function properly if the connections are reversed.
 Brake hose (front brake master cylinder to hydraulic unit brake pipe joint)  “1” inlet: from the 
front brake master cylinder
 Brake hose (hydraulic unit brake pipe joint to front brake calipers)  “2” outlet: to the front brake 
calipers
4 Brake lines
Check the brake lines for kinks 
and deterioration.
WARNING
EWA23P1020
Only use genuine Yamaha 
parts. Using other...

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-108
TIP
 If the brake hose inlet and outlet connections are incorrect on the hydr\
aulic unit brake pipe joint, the 
brake lever will be pulled to its full-stroke position without responding, and then it will be pushed back 
slowly without pulsating when the final check on page  “[D-3] FINAL CHECK”  on page 8-121 is per-
formed.
 If the front and rear brake hose connections are reversed on the hydraulic unit brake pipe joint, the 
pulsating action in the brake lever...

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-109
Fault code No. 42 Symptom Rear wheel will not recover from the locking ten- dency even though the signal is continuously 
transmitted from the ABS ECU to release the hy-
draulic pressure (when the battery voltage is 
normal).
Order Item/components and probable  cause Check or maintenance job Reinstatement 
confirmation 
method
1 Rotation of wheel Check that there is no brake 
disc drag on the rear wheel and 
make sure that it rotates 
smoothly.
 Check for brake...

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-110
WARNING
EWA23P1022
The rear brake will not function properly if the connections are reversed.
 Brake hose (rear brake master cylinder to hydraulic unit brake pipe joint)  “1” inlet: from the 
rear brake master cylinder
 Brake hose (hydraulic unit brake pipe joint to rear brake caliper)  “2” outlet: to the rear brake 
caliper
TIP
If the brake hose inlet and outlet connections are reversed on the hydra\
ulic unit brake pipe joint, the 
brake pedal will be pressed...

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-111
Fault code No. 51 Symptom Power voltage is too high.
Order Item/components and probable  cause Check or maintenance job Reinstatement 
confirmation 
method
1 Battery voltage Replace the battery.
Refer to “CHECKING AND 
CHARGING THE BATTERY ” on 
page 8-132. 
Set the main 
switch to  “ON” 
and check 
that the ABS 
warning light 
comes on for 
2 seconds, 
then goes off.
 Perform a tri-
al run at a 
constant 
speed of 30 
km/h and 
check that the 
ABS warning 
light...