2012 Na Yamaha Super Tenere Manual

haha ABS (ANTI-LOCK BRAKE SYSTEM)8-122  

haha ELECTRICAL COMPONENTS
8-123
EAS27973
ELECTRICAL COMPONENTS
56
8
9
4
10
11
12
13141516
17
18
7
1
3
2   

haha ELECTRICAL COMPONENTS
8-124
1. Main switch
2. Front brake light switch
3. Clutch switch
4. Intake air temperature sensor
5. Throttle servo motor
6. Throttle position sensor
7. Accelerator position sensor
8. Intake air pressure sensor
9. Fuel pump
10. Rear brake light switch
11. Sidestand switch
12. Oil level switch
13. Cylinder-#1 left ignition coil
14. Cylinder-#1 right ignition coil
15. Cylinder-#2 left ignition coil
16. Cylinder-#2 right ignition coil
17. Radiator fan motor
18. Horn  

haha ELECTRICAL COMPONENTS
8-125
1
2
3
4
56
7
8
10
9
11
13
1514
16
12
17
18
19    

haha ELECTRICAL COMPONENTS
8-126
1. Rectifier/regulator
2. Relay unit
3. Main fuse
4. Radiator fan motor relay
5. Turn signal relay
6. Headlight relay
7. ECU (engine control unit)
8. Starter relay
9. ABS motor fuse
10. Hydraulic unit assembly
11. Lean angle sensor
12. Coolant temperature sensor
13. Battery
14. Neutral switch
15. Crankshaft position sensor
16. O 2 sensor #1
17. O 2 sensor #2
18. Fuse box 1
19. Fuse box 2  

haha ELECTRICAL COMPONENTS
8-127
EAS27981
CHECKING THE SWITCHES
G/YBr
MODE
Sb
L/B L/YON
OFFRBr/L Br/RDgBr/WCh
R/WR/B
W/GB/W L/W
B
Br
B/WR/YY
BB
(GRAY)
Br Y
(BROWN)
G/Y
R/BBBr
L/WR/W
R/YBr/W
B DgBrB/Y
Y
L/Y
Ch
( BLACK )
L/Y
B/Y
(BLACK)
W
(BLACK)
Br/R
L/YL/B
R
Br/L
4
6 5
1
3
2
10
13
9
12
11
7
8  

haha ELECTRICAL COMPONENTS
8-128
1. Dimmer switch
2. Turn signal switch
3. Horn switch
4. Engine stop switch
5. Start switch
6. D-mode switch
7. Front brake light switch
8. Rear brake light switch
9. Neutral switch
10. Sidestand switch
11. Oil level switch
12. Clutch switch
13. Main switch  

haha ELECTRICAL COMPONENTS
8-129
Check each switch for continuity with the pocket tester. If the continuity reading is incorrect, check the 
wiring connections and if necessary, replace the switch.
NOTICE
ECA14370
Never insert the tester probes into the coupler terminal slots  “a”. Always insert the probes from 
the opposite end of the coupler, taking care not to loosen or damage the leads.
TIP
Before checking for continuity, set the pocket tester to  “0” and to the “  ×  1 ” range.
 When checking for...

haha ELECTRICAL COMPONENTS
8-130
EAS27990
CHECKING THE BULBS AND BULB 
SOCKETS
TIP
Do not check any of the lights that use LEDs.
Check each bulb and bulb socket for damage or 
wear, proper connections, and also for continuity 
between the terminals.
Damage/wear   Repair or replace the bulb, 
bulb socket or both.
Improperly connected   Properly connect.
No continuity   Repair or replace the bulb, bulb 
socket or both.
Types of bulbs
The bulbs used on this vehicle are shown in the 
illustration on the...

haha ELECTRICAL COMPONENTS
8-131
Checking the condition of the bulb sockets
The following procedure applies to all of the bulb 
sockets.
1. Check: Bulb socket (for continuity)
(with the pocket tester)
No continuity   Replace.
TIP
Check each bulb socket for continuity in the 
same manner as described in the bulb section; 
however, note the following.
▼▼▼▼ ▼ ▼▼▼ ▼▼▼▼▼ ▼ ▼ ▼▼▼▼ ▼ ▼▼▼▼ ▼ ▼▼▼ ▼▼▼▼
a. Install a good bulb into the bulb socket.
b. Connect the pocket tester probes to the re-
spective leads of...