Yamaha Promix 1 Manual

 
Preset Effects Program Parameters 
43 
ProMix 01 User’s Guide 
Program 23—CHORUS 
A stereo chorus. Produces a rich thickening effect. Good with guitar, bass, and strings. 
Parameter Setting Range Description
Mod.Freq 
0.6Hz 0.1–20.0Hz Modulation speed. 
AM Depth 
49% 0–100% Amplitude modulation depth. The amount of amplitude modulation. 
PM Depth 
35% 0–100% Pitch modulation depth. The amount of pitch modulation. 
Mod.Dly 
12.1ms –99...+99% Modulation delay. The delay time before modulation starts....

 
44 
Chapter 4: Auxiliaries and Effects 
ProMix 01 User’s Guide 
Program 28—PHASING
Stereo phaser. Similar to flange, but different. Good with guitar, strings, and other rich harmonic sounds.
Parameter Setting Range Description
Mod.Freq0.5Hz 0.1–20.0Hz Modulation speed.
Mod.Depth58% 0–100% Modulation depth. The amount of modulation.
FB.Gain+47% –99...+99% Feedback gain. The amount of processed signal fed back into the phaser.
Phase Ofst24 0–100 Phase offset. The amount that the signal phase is offset....

SEND3 and SEND445
ProMix 01 User’s Guide
SEND3 and SEND4
SEND3 and SEND4 can be used to feed external effects processors, 
foldback amplifiers, or multitrack recording equipment. When used 
to feed an external effects processor, the processed signal can be 
returned via the stereo input channel or an unused input channel. 
Input channel and stereo input channels signals can be fed to SEND3 
and SEND4. 
The master send level is set using the RTN/SEND fader. When the 
SEND3 LCD function is selected, the...

46Chapter 4: Auxiliaries and Effects
ProMix 01 User’s Guide
SEND3-4 Stereo Pair
SEND3 and SEND4 can be linked for use as a stereo pair. In this way 
they can, essentially, be used as another pair of stereo outputs, allow-
ing for another stereo mix to be set up. This is called SEND3-4 Stereo 
mode. Independent, or normal operation is called Mono mode. 
In Stereo mode, the SEND3 and SEND4 LCD functions are combined 
into the SEND3-4 LCD function. This LCD function can be selected 
by pressing either...

SEND3-4 Channel Pans & Balance47
ProMix 01 User’s Guide
SEND3-4 Channel Pans & Balance
In SEND3-4 Stereo mode, a SEND3-4 pan control is available on each 
input channel and a SEND3-4 balance control is available on the ste-
reo input channel (ST IN). These controls appear on the SEND3-4 
LCD function, shown below. After pressing either [SEND3] or 
[SEND4], press the [
¨] cursor button to access the SEND3-4 pan dis-
play. Alternatively, press the [SEND3] or [SEND4] button again. See 
“Pan and Balance” on...

48Chapter 4: Auxiliaries and Effects
ProMix 01 User’s Guide
SEND3-4 Block Diagram
This block diagram shows what happens when SEND3 and SEND4 
are configured as a stereo pair: Input channel SEND3 and SEND4 
controls become a single control, and a SEND3-4 pan control 
appears. On the stereo input channel, a SEND3-4 balance control 
appears. The left signal feeds SEND3 and the right signal feeds 
SEND4. Levels are controlled together. On the SEND3-4 outputs, a 
SEND3-4 output balance control appears. See...

 
CUE 
49 
ProMix 01 User’s Guide 
5 
CUE 
In this chapter... 
About CUE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   50
CUE Modes   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   50
Group CUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   50
Setting the CUE Mode . . . . . . . . . . . . . . . . . . . . . . . . .   51
CUE Signal Sources  . . . . . . . . . . . . . . . . . . . . . . . . . . .   51
CUE/2TR IN Switch   . . . . . . . . . . ....

 
50 
Chapter 5: CUE 
ProMix 01 User’s Guide 
About CUE 
ProMix 01 CUE provides comprehensive monitoring of virtually all 
inputs and outputs. The CUE signal is output to the MONITOR 
OUTPUT and PHONES. Output levels are controlled using the 
MONITOR OUT LEVEL control and PHONES LEVEL control, 
respectively.  
CUE Modes 
There are three CUE modes: MIX, LAST CUE, and ST FIX. The fol-
lowing table shows how they work in relation to the LCD functions.  
MIX  
 — this mode can be used only when the CUE LCD...

 
Setting the CUE Mode 
51 
ProMix 01 User’s Guide 
Setting the CUE Mode 
CUE modes are set on the CUE LCD function, shown below. The 
name of the current CUE mode is highlighted. The PARAMETER 
wheel is used to select modes. When another mode is selected, its 
name flashes. If it is activated by pressing [ENTER], it stops flashing, 
appears highlighted, and becomes the current CUE mode.  
CUE Signal Sources 
The following table shows where the various CUE signals are sourced.
n/a: not applicable. 
CUE/2TR...

 
52 
Chapter 5: CUE 
ProMix 01 User’s Guide 
CUE LCD Function Info 
As well as being used to set the CUE mode, the CUE LCD function 
displays various information about the currently selected channel. 
The exact information shown depends on the type of channel 
selected. CUE displays for each type of channel are shown below.  
Input Channel 
This is the CUE LCD function when an input channel is selected.  
Stereo-Pair Input Channels 
This is the CUE LCD function when stereo-pair input channels are...