Yamaha Promix 1 Manual

 
Troubleshooting 
93 
ProMix 01 User’s Guide 
Troubleshooting 
Trouble Remedy  
ProMix 01 cannot be powered ON.Make sure that the ProMix 01 power cable is connected to an AC receptacle of the type 
marked on the rear panel.
Make sure that the POWER switch is in the ON position.
If installed, check the mains plug fuse.
The signal phase sounds odd.Make sure that the PHASE LCD function is set correctly.
Make sure that your balanced cables are wired correctly.
The input signal sounds distorted but 
the...

 
94 
Troubleshooting 
ProMix 01 User’s Guide 

 
Appendix 
95 
ProMix 01 User’s Guide 
Appendix 
In this chapter... 
LCD Function Map   . . . . . . . . . . . . . . . . . . . . . . . . . . .   96
Button Protector   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   97
Data Types   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   98
Error Messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   100
ProMix 01 Compatible Products   . . . . . . . . . . . . . . .   104
General Specifications  . . . . . . . . . ....

 
96 
Appendix 
ProMix 01 User’s Guide 
LCD Function Map
UTILITY menu OSCILLATOR kP.90
SEND3, 4 CONFIGURATION 
kP.49
OUTPUT COMP PATCH POINT 
kP.74
MEMORY PROTECT 
kP.65
BATTERY CHECK 
kP.91
MIDI menu MIDI SETUP 
kP.81
PROGRAM CHANGE ASSIGN 
kP.82
CONTROL CHANGE ASSIGN 
kP.83
BULK DUMP/REQUEST 
kP.85
LOCAL ON/OFF 
kP.86
MEMORY CONTROL CHANGE OUT 
kP.87
MEMORY 
kP.63
GROUP 
kP.56
PAIR 
kP.58
METER 
kP.21
PAN/
Æ kP.28
COMP 
kP.72
CUE 
kP.51
SEND1 
kP.34
SEND2 
kP.34
SEND3 
kP.48
SEND4 
kP.48
SEND3-4...

 
Button Protector 
97 
ProMix 01 User’s Guide 
Button Protector 
If you find that your hand accidentally presses the ST OUT [ON] but-
ton when operating the PARAMETER wheel, affix the self-adhesive 
Button Protector as shown below. 
SEL
ON
14
6
0
5
10
20
40
60
00
14
SEL
ON
15
6
0
5
10
20
40
60
00
15
SEL
ON
16
6
0
5
10
20
40
60
00
16
SEL
ON
6
0
5
10
20
40
60
00
ST IN
SEL
ON
6
0
5
10
20
40
60
00
RTN/
SEND
SEL
ON
6
0
5
10
20
40
60
00
ST OUT
ST INRTN/
SEND ST OUT
CLIP
15
12
9
6
3
0
±6
±12
±18
±24
±40
ENTER...

 
98 
Appendix 
ProMix 01 User’s Guide 
Data Types 
Mix Scene Data
Edit Buffer Data 
Same as Mix Scene data. 
Control Data 
This is the MIDI Control Change to ProMix 01 Parameter Assign-
ment Table. See the Additions section at the end of this   
User’s Guide  
. 
Program Data 
This is the ProMix 01 Mix Scene to MIDI Program Change Assign-
ment Table. See the Additions section at the end of this   
User’s Guide  
. 
Data Source Details  
Mix scene name Eight characters
ON/OFF buttonsCH1–16, ST IN, SEND3,...

 
Data Types 
99 
ProMix 01 User’s Guide 
Setup Memory Data 
MIDI Data Details  
Tx channel 1–16
Rx channel 1–16
Control Change mode Channel/register
Control Change Tx ON/OFF
Control Change Rx ON/OFF
Control Change OMNI ON/OFF
Control Change ECHO ON/OFF
Program Change Tx ON/OFF
Program Change Rx ON/OFF
Program Change OMNI ON/OFF
Program Change ECHO ON/OFF
Bulk Tx ON/OFF
Bulk Rx ON/OFF
Bulk OMNI ON/OFF
MIDI Tx interval 0–1sec (100ms steps)
MIDI Local ON/OFF ON/OFF
MIDI Local fader levels CH1–16 fader...

 
100 
Appendix 
ProMix 01 User’s Guide 
Error Messages 
ERROR! System Error[1] 
A fatal error has occurred. Initialize ProMix 01. See “ProMix 01 Ini-
tialization” on page 92. 
ERROR! System Error[2] 
A fatal error has occurred. Initialize ProMix 01. See “ProMix 01 Ini-
tialization” on page 92. 
ERROR! System Error[3] 
A fatal error has occurred. Initialize ProMix 01. See “ProMix 01 Ini-
tialization” on page 92. 
ERROR! System Error[4] 
A fatal error has occurred. Initialize ProMix 01. See “ProMix 01...

 
Error Messages 
101 
ProMix 01 User’s Guide 
MIDI Parity Error 
A MIDI receive error has occurred. Check the transmission data and 
connecting cable. 
MIDI Framing Error 
A MIDI receive error has occurred. Check the transmission data and 
connecting cable. 
MIDI Over Run Error 
A MIDI receive error has occurred. Reduce the transmission data. 
SUB->MAIN CPU Parity Error 
An error has occurred while receiving fader data from the CPU. 
SUB->MAIN CPU Framing Error 
An error has occurred while receiving...

 
102 
Appendix 
ProMix 01 User’s Guide 
MAIN->SUB Over Run Error 
An error has occurred while receiving fader data from the CPU. 
WARNING! No battery. 
No battery is installed. Ask your Yamaha dealer to install one. 
WARNING! Low battery. 
Battery power is getting low. Ask your Yamaha dealer to install a new 
battery. 
Scene memory 00 is read only. 
Mix scene 00 is read only. Select another mix scene. 
Scene memories 01-25 are protected. 
Scene memories 1 through 25 are protected. To store, first turn...