Yamaha Av1 Service Manual

En
51
dIn the same way, perform the angle measurement for the 
positions “2” and “3”.
The following screen appears on the TV when the third angle 
measurement finishes.
3
Use the cursor keys to select “Save/Cancel” and 
press ENTER. To check the measurement results, select “Result”. For details, see 
“Checking the measurement results” (p.53).
4
To save the measurement results, use the cursor 
keys to select “SAVE” and press ENTER.The corrected speaker settings are applied. To finish the measurement...

En
52
2
Move the YPAO microphone to the next listening 
position and press ENTER.Repeat step 2 until the measurement at all listening 
positions (up to 8) are made.
3
If the measurement at all listening position are 
made, use the cursor keys to select “CANCEL” and 
press ENTER.If you have made the measurement at 8 listening positions, 
the following screen appears automatically.
(When the angle measurement is disabled)
Proceed to step 5.
(When the angle measurement is enabled)
Proceed to step 4.
4...

En
53
5
Use the cursor keys to select “Save/Cancel” and 
press ENTER. To check the measurement results, select “Result”. For details, see “Checking the measurement results” (p.53).
6
To save the measurement  result, use the cursor 
keys to select “SAVE” and press ENTER.The corrected speaker settings are applied. To finish the measurement without saving the result, select “CANCEL”.
7
Disconnect the YPAO microphone from this unit.
Now optimization of the sp eaker settings is complete.Checking the...

En
54
Reloading the previous YPAO resultsWhen the speaker settings you have configured manually are not 
suitable, follow the procedure below to discard the manual settings 
and reload the previous YPAO results.1
In the “Setup” menu, select “Speaker”, “Auto 
Setup” and then “Result” (p.106).
2
Use the cursor keys to select “Setup Reload” and 
press ENTER.
3
To exit from the menu, press ON SCREEN.
SOURCERECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL...

En
55
Error messagesIf any error message is displayed during the measurement, resolve the problem and perform YPAO again.
Error message
Cause
Remedy
E-1: No Front SP Front speakers are not detected.
Follow the on-screen instructions to exit YPAO, turn off this unit, and then check the speaker connections.
E-2: No Sur. SP Either of surround speakers is not detected.
E-3: No F.PRNS SP Either of front presence speakers is not detected.
E-4: SBR SBL A surround back speaker is connected to the R side only....

En
56
Warning messagesEven if any warning message is displayed after the measurement, you can save the measurement results by following on-screen ins tructions.
However, we recommend you perform YPAO again to  use this unit with the optimal speaker settings.
Warning message
Cause
Remedy
W-1: Out of Phase Any of the speaker cables may be connected with the 
reversed polarity (+/-). Select “Wiring” in “Result” (p.53) and check the 
cable connections (+/-) of the speaker indicated with 
“Reverse”. If the...

En
57
PLAYBACK1
Turn on external devices (TV, BD/DVD player, etc.) 
connected to this unit.
2
Use the input selection keys to select an input 
source.
3
Start playback on the external device, or select a 
radio station.Refer to the instruction manual of the external device.
For details on the following operations, see the 
corresponding pages.
- Listening to FM/AM radio (p.65)
- Playing back iPod music/videos (p.70)
- Playing back music via Bluetooth (p.75)
- Playing back music stored on a USB storage...

En
58
The SCENE function allows you to select the assigned input source, sound program, HDMI output and various settings at once.
You can use up to 12 scenes to register your favorite settings and switch them depending on a playback source.1
Press SCENE.The input source and settings registered to the 
corresponding scene are selected. This unit turns on 
automatically when it is in standby mode.
By default, the following settings are registered for each scene. You can select SCENE1~4 by pressing SCENE on...

En
59
Configuring scene assignmentsFollow the procedure below to register the current status (input 
source, sound program, etc.) to a scene. As necessary, you can 
select items to be included as the scene assignments (p.102).1
Set this unit to the condition (input source, sound 
program, etc.) that you wa nt to assign to a scene.
2
Hold down the desired SCENE key until “SET 
Complete” appears on the front display.
3
If you want to control the corresponding playback 
device after selecting the scene,...

En
60
This unit is equipped with a variety of sound programs and 
surround decoders that allow you to enjoy playback sources with a 
favorite sound mode (sound field effect, stereo playback, etc).
Selecting a sound program suitable for movies
- MOVIE THEATER category (p.61):Press MOVIE repeatedly.
- ENTERTAINMENT category (p.61): Press ENTERTAIN repeatedly.
Selecting a sound program suitable for music or stereo 
playback
- CLASSICAL category (p.62): Press CLASSICAL repeatedly.
- LIVE/CLUB category...