Yamaha Av1 Service Manual

							En
51
dIn the same way, perform the angle measurement for the 
positions “2” and “3”.
The following screen appears on the TV when the third angle 
measurement finishes.
3
Use the cursor keys to select “Save/Cancel” and 
press ENTER. To check the measurement results, select “Result”. For details, see 
“Checking the measurement results” (p.53).
4
To save the measurement results, use the cursor 
keys to select “SAVE” and press ENTER.The corrected speaker settings are applied. To finish the measurement without saving the result, select “CANCEL”.
5
Disconnect the YPAO microphone from this unit.
Now optimization of the sp eaker settings is complete.
Measuring at multiple listening positions (multi measure)When “Multi Position” is set to “Yes”, follow the procedure below to 
make the measurement. YPAO measurement is not performed correctly when any obstacles are in the 
room.
 During the measuring process, keep stuff in the corners or remove it from the  room. It takes about 15 minutes to make the measurement at 8 listening positions.
 If any error message (such as E-1) or warning message (such as W-1) appears,  see “Error messages” (p.55) or “Warning messages” (p.56).1
To start the measurement,  use the cursor keys to 
select “Measure” and press ENTER.The measurement will start in 10 seconds. Press ENTER 
again to start the measurement immediately. To cancel the measurement, press RETURN.The following screen appears on the TV when the 
measurement at the first position finishes.
Caution Since the YPAO microphone is sensitive to heat, do not place the microphone  in any place where it will be subjected to direct sunlight or high temperatures 
(top of an AV equipment, etc).
SOURCE RECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
INPUT
PURE
DIRECT
MUTE
TVSCENE
1
2
3
4
PROGRAM
VOLUME
TV VOLMUTE
MODETOP MENURETURN
DISPLAYPOP-UP/MENUTV CH
PRESET
ENTER
ON SCREEN
OPTION
SOURCERECEIVER
AVAUDIO
1
2
3
4
5
6
7
V-AUX
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B]
[ A]
ENTER
RETURN  ENTER
RETURN Cursor keys
1
2
3
4
5
6
7
8
9Automatic speaker setup 
						

							En
52
2
Move the YPAO microphone to the next listening 
position and press ENTER.Repeat step 2 until the measurement at all listening 
positions (up to 8) are made.
3
If the measurement at all listening position are 
made, use the cursor keys to select “CANCEL” and 
press ENTER.If you have made the measurement at 8 listening positions, 
the following screen appears automatically.
(When the angle measurement is disabled)
Proceed to step 5.
(When the angle measurement is enabled)
Proceed to step 4.
4
Perform the angle measurement.a Use the cursor keys to select “YES” and press ENTER.
Select “NO” to cancel the angle measurement. b
Place the supplied microphone base at the listening position 
you will be seated most frequently and set the YPAO 
microphone to the position “1”.
 We recommend using a tripod to place the microphone base at ear height. 
Use the tripod screws to fix the microphone base in place.c Press ENTER to start the first angle measurement.
The following screen appears on the TV when the first angle 
measurement finishes.
d In the same way, perform the angle measurement for the 
positions “2” and “3”.
The following screen appears on the TV when the third angle 
measurement finishes.
FRONT
DIRECTION
Microphone 
base
SOURCE RECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
INPUT
PURE
DIRECT
MUTE
TVSCENE
1
2
3
4
PROGRAM
VOLUME
TV VOLMUTE
MODETOP MENURETURN
DISPLAYPOP-UP/MENUTV CH
PRESET
ENTER
ON SCREEN
OPTION
SOURCERECEIVER
AVAUDIO
1
2
3
4
5
6
7
V-AUX
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B]
[ A]
ENTER ENTER Cursor keys
1
2
3
4
5
6
7
8
9Automatic speaker setup 
						

							En
53
5
Use the cursor keys to select “Save/Cancel” and 
press ENTER. To check the measurement results, select “Result”. For details, see “Checking the measurement results” (p.53).
6
To save the measurement  result, use the cursor 
keys to select “SAVE” and press ENTER.The corrected speaker settings are applied. To finish the measurement without saving the result, select “CANCEL”.
7
Disconnect the YPAO microphone from this unit.
Now optimization of the sp eaker settings is complete.Checking the measurement resultsYou can check the YPAO measurement results.1
After the measurement, use the cursor keys to 
select “Result” and press ENTER. You can also select “Result” from “Auto Setup” (p.107) in the “Setup” menu. 
In this case, the previous measurement results are displayed.
The following screen appears.1 Measurement result items
2 Measurement result details
3 The number of measured positions (when multi 
measure is performed)
2
Use the cursor keys to select an item A speaker with any problem is indicated with a red-boxed message.
3
To finish checking the re sults and return to the 
previous screen, press RETURN.
Caution Since the YPAO microphone is sensitive to heat, do not place the microphone  in any place where it will be subjected to direct sunlight or high temperatures 
(top of an AV equipment, etc).
Wiring Polarity of each speaker
Normal:
 The speaker cable is connected with the 
correct polarity (+/-).
Reverse:  The speaker cable may be connected with 
the reversed polarity (+/-).
Size Size of each speaker (cross-over frequency of the 
subwoofer)
Large:
 The speaker can reproduce low-frequency 
signals effectively.
Small:  The speaker cannot reproduce low-frequency 
signals effectively.
Distance Distance from the listening position to each speaker
Level Output level adjustment for each speaker
Angle Angle of each speaker at the listening position
23
1
1
2
3
4
5
6
7
8
9Automatic speaker setup
SOURCE
RECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
INPUT
PURE
DIRECT
MUTE
TVSCENE
1
2
3
4
PROGRAM
VOLUME
TV VOLMUTE
MODETOP MENURETURN
DISPLAYPOP-UP/MENUTV CH
PRESET
ENTER
ON SCREEN
OPTION
SOURCERECEIVER
AVAUDIO
1
2
3
4
5
6
7
V-AUX
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B]
[ A]
ENTER
RETURN  ENTER
RETURN Cursor keys 
						

							En
54
Reloading the previous YPAO resultsWhen the speaker settings you have configured manually are not 
suitable, follow the procedure below to discard the manual settings 
and reload the previous YPAO results.1
In the “Setup” menu, select “Speaker”, “Auto 
Setup” and then “Result” (p.106).
2
Use the cursor keys to select “Setup Reload” and 
press ENTER.
3
To exit from the menu, press ON SCREEN.
SOURCERECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
INPUT
PURE
DIRECT
MUTE
TVSCENE
1
2
3
4
PROGRAM
VOLUME
TV VOLMUTE
MODETOP MENURETURN
DISPLAYPOP-UP/MENUTV CH
PRESET
ENTER
ON SCREEN
OPTION
SOURCERECEIVER
AVAUDIO
1
2
3
4
5
6
7
V-AUX
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B]
[ A]
ENTER ENTER ON SCREEN  ON SCREEN Cursor keys
1
2
3
4
5
6
7
8
9Automatic speaker setup 
						

							En
55
Error messagesIf any error message is displayed during the measurement, resolve the problem and perform YPAO again.
Error message
Cause
Remedy
E-1: No Front SP Front speakers are not detected.
Follow the on-screen instructions to exit YPAO, turn off this unit, and then check the speaker connections.
E-2: No Sur. SP Either of surround speakers is not detected.
E-3: No F.PRNS SP Either of front presence speakers is not detected.
E-4: SBR SBL A surround back speaker is connected to the R side only. When using only one surround back sp
eaker, you need to connect it to the SINGLE jack (L side). Follow the 
on-screen instructions to exit YPAO, turn  off this unit, and then reconnect the speaker.
E-5: Noisy The noise is too loud. Keep the room quiet and follow the on-screen instructio
ns to start the measurement again. If you select 
“PROCEED”, the measurement starts again on the condit ion this unit ignores the noisy error even if noises 
are detected.
E-6: Check Sur. Any surround back speaker is
 connected while no surround 
speakers are connected. Surround speakers should be connected when using 
surround back speakers. Follow the on-screen 
instructions to exit YPAO, turn off this unit, and then reconnect the speakers.
E-7: No MIC The YPAO microphone has been removed. Connect the YPAO microphone to the YPAO MIC jack firm
ly and follow the on-screen instructions to start the 
measurement again.
E-8: No Signal The YPAO microphone cannot detect test tones. Connect the YPAO microphone to the YPAO MIC jack firm
ly and follow the on-screen instructions to start the 
measurement again. If this error occurs repeatedly, cont act the nearest authorized Yamaha dealer or service 
center.
E-9: User Cancel The measurement has been canceled. Follow the on-screen instructions to start the measurement again. To cancel the measurement,  select “EXIT”.
E-10: Internal Error An internal error has occurred. Follow the on-screen instructions to exit YPAO, turn off and on this unit. If this error occurs repeatedly, 
contact the nearest authorized Yamaha dealer or service center.
E-11: No R.PRNS SP Either of rear presence speakers is not detected. Follow the on-screen instructions to exit YPAO, turn off this unit, and then c heck the speaker connections.
1
2
3
4
5
6
7
8
9Automatic speaker setup 
						

							En
56
Warning messagesEven if any warning message is displayed after the measurement, you can save the measurement results by following on-screen ins tructions.
However, we recommend you perform YPAO again to  use this unit with the optimal speaker settings.
Warning message
Cause
Remedy
W-1: Out of Phase Any of the speaker cables may be connected with the 
reversed polarity (+/-). Select “Wiring” in “Result” (p.53) and check the 
cable connections (+/-) of the speaker indicated with 
“Reverse”. If the speaker is connected incorrectly, turn  off this unit and then reconnect the speaker cable. 
Depending on the type of speakers or room environm ent, this message may appear even if the speakers are 
connected correctly.
W-2: Over Distance Any of the speakers is placed more than 24 m from the 
listening position. Select “Distance” in “Result” (p.53) and move the 
speaker indicated with “>24.0m (>80.0ft)” within 24 m of 
the listening position.
W-3: Level Error There are a significant volume differences between the 
speakers. Check the use environment and cable connections (+/-) 
of each speaker, and the volume of the subwoofer. 
We recommend using the same speakers or speake rs with as similar specifications as possible.
1
2
3
4
5
6
7
8
9Automatic speaker setup 
						

							En
57
PLAYBACK1
Turn on external devices (TV, BD/DVD player, etc.) 
connected to this unit.
2
Use the input selection keys to select an input 
source.
3
Start playback on the external device, or select a 
radio station.Refer to the instruction manual of the external device.
For details on the following operations, see the 
corresponding pages.
- Listening to FM/AM radio (p.65)
- Playing back iPod music/videos (p.70)
- Playing back music via Bluetooth (p.75)
- Playing back music stored on a USB storage device (p.77)
- Playing back music stored on PCs (p.80)
- Listening to Internet radio (p.83)
4
Press VOLUME to adjust the volume. To mute the audio output, press MUTE. Press MUTE again to unmute.
 To adjust treble/bass parts of sound, use the “Option” menu or TONE/BALANCE on the front panel (p.96).On-screen input selection
a
Press ON SCREEN.
b
Use the cursor keys to select “Input” and press ENTER.
c
Use the cursor keys to select a desired input source and press 
ENTER.
Selecting an HDMI output jack1
Press HDMI OUT to select an HDMI OUT jack.Each time you press the key, the HDMI OUT jack to be 
used for signal output switches. You can also select an HDMI output jack by selecting a scene (p.58).
 When “HDMI OUT 1+2” is selected, this unit outputs video signals at the highest resolution that both TVs connected to this unit support. (For 
example, if you have connected a 1080p TV to the HDMI OUT 1 jack, and a 
720p TV to the HDMI OUT 2 jack, this unit outputs 720p video signals.)
Basic playback procedure
HDMI OUT 1+2 Outputs the same signal at both the HDMI OUT 1 
and HDMI OUT 2 jacks.
HDMI OUT 1 Outputs the signals at the selected HDMI OUT 
jack.
HDMI OUT 2
HDMI OUT Off Does not output the signals at the HDMI OUT jacks.OUT 1INOUT 2
VOLUMEMUTE
DRC
ADAPTIVE
3
ZONE2
SBLPL
SBRSBPR
SW1SL
SW2
SWSR
PLCLRPR
STEREOENHANCER
SLEEPHD
TUNEDPREAMPPA R T Y
ZONE3ZONE4
HDTAGDOCK
OUT1+2 HDMIOUTSel.
SOURCE
RECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
INPUT
PURE
DIRECT
MUTE
TVSCENE
1
2
3
4
PROGRAM
VOLUME
TV VOLMUTE
MODETOP MENURETURN
DISPLAYPOP-UP/MENUTV CH
PRESET
ENTER
ON SCREEN
OPTION
2
3
5
1
46
TUN./ CH
ENHANCER
SUR.
DECODE
HDMI OUT
MEMORY
INFO AM
PA R T YFM
0
  10
LEVEL
ENT
SETUP
ZONE
8
7
SLEEP
9
SOURCERECEIVER
TUN./ CH
HDMI OUTHDMI OUTON SCREEN  ON SCREEN ENTER ENTER 
MUTEVOLUME
[ B]
[ A]
Cursor keys Input selection keys 
						

							En
58
The SCENE function allows you to select the assigned input source, sound program, HDMI output and various settings at once.
You can use up to 12 scenes to register your favorite settings and switch them depending on a playback source.1
Press SCENE.The input source and settings registered to the 
corresponding scene are selected. This unit turns on 
automatically when it is in standby mode.
By default, the following settings are registered for each scene. You can select SCENE1~4 by pressing SCENE on the remote control. 
Additionally, you can create 8 scenes (SCENE5~12) and select those scenes from 
the “Scene” menu (p.100).
 You can also include other setting items (surround settings, video settings, etc.) as  the scene assignments (p.102).
On-screen scene selection
a
Press ON SCREEN.
b
Use the cursor keys to select “Scene” and press ENTER.
c
Use the cursor keys to select a desired scene and press 
ENTER.Selecting the input source and favorite settings at once (SCENE)SCENE (SCENE key)
1 (BD/DVD)
2 (TV)
3 (CD)
4 (RADIO)
Input Input (p.57)
AV1 AUDIO1 AUDIO2 TUNER
Audio Select (p.97) Auto Auto Auto -
HDMI Output HDMI Output (p.57) OUT 1+2 OUT 1+2 OUT 1+2 OUT 1+2
Mode Sound Program (p.60)
Drama STRAIGHT STRAIGHT 9ch Stereo
Pure Direct Mode (p.113) Auto Auto Auto Auto
Sound Tone Control (p.96):
SP (speakers), HP (headphones)
Treble/Bass: 0.0dB Treble/Bass: 0.0dB Treble/Bass: 0.0dB Treble/Bass: 0.0dB
Adaptive DRC (p.96) Off On Off Off
Enhancer (p.64) OffOnOffOn
SOURCE
RECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
INPUT
PURE
DIRECT
MUTE
TVSCENE
1
2
3
4
PROGRAM
VOLUME
TV VOLMUTE
MODETOP MENURETURN
DISPLAYPOP-UP/MENUTV CH
PRESET
ENTER
ON SCREEN
OPTION
SOURCERECEIVER
AVAUDIO
1
2
3
4
5
6
7
V-AUX
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B]
[ A]
ON SCREEN  ON SCREEN ENTER ENTER SCENECursor keys 
						

							En
59
Configuring scene assignmentsFollow the procedure below to register the current status (input 
source, sound program, etc.) to a scene. As necessary, you can 
select items to be included as the scene assignments (p.102).1
Set this unit to the condition (input source, sound 
program, etc.) that you wa nt to assign to a scene.
2
Hold down the desired SCENE key until “SET 
Complete” appears on the front display.
3
If you want to control the corresponding playback 
device after selecting the scene, hold down the 
corresponding SCENE key  and input selection key 
together for more than 3 seconds.Once the setting is completed successfully, SOURCE/
RECEIVER blinks twice. If you have not registered the remote control code of the playback device  yet, see “Setting the remote control codes for playback devices” (p.130) to 
register it.
 You can start playback of external devices connected to this unit via HDMI  or a Yamaha product connected to the REMOTE OUT jack, in conjunction 
with a scene selection (SCENE link playback). To enable the SCENE link 
playback, specify the device type in “Device Control” (p.101) in the “Scene” 
menu.OUT 1INOUT 2
VOLUMEMUTE
DRC
ADAPTIVE
3
ZONE2
SBLPL
SBRSBPR
SW1SL
SW2
SWSR
PLCLRPR
STEREOENHANCER
SLEEPHD
TUNEDPREAMPPA R T Y
ZONE3ZONE4
HDTAGDOCK
SETComplete SCENE1
SOURCE
RECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
INPUT
PURE
DIRECT
MUTE
TVSCENE
1
2
3
4
PROGRAM
VOLUME
TV VOLMUTE
MODETOP MENURETURN
DISPLAYPOP-UP/MENUTV CH
PRESET
ENTER
ON SCREEN
OPTION
AVAUDIO
1
2
3
4
5
6
7
V-AUX
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B]
[ A]
SCENESOURCE/RECEIVER 
						

							En
60
This unit is equipped with a variety of sound programs and 
surround decoders that allow you to enjoy playback sources with a 
favorite sound mode (sound field effect, stereo playback, etc).
Selecting a sound program suitable for movies
- MOVIE THEATER category (p.61):Press MOVIE repeatedly.
- ENTERTAINMENT category (p.61): Press ENTERTAIN repeatedly.
Selecting a sound program suitable for music or stereo 
playback
- CLASSICAL category (p.62): Press CLASSICAL repeatedly.
- LIVE/CLUB category (p.62): Press LIVE/CLUB repeatedly.
- STEREO category (p.62): Press STEREO repeatedly.
Selecting a surround decoder (p.63)
Press SUR.DECODE repeatedly.
Switching to the straight decode mode (p.63)
Press STRAIGHT.
Switching to the Pure Direct mode (p.64)
Press PURE DIRECT.
Enable Compressed Music Enhancer (p.64)
Press ENHANCER. You can also select a sound program or the surround decoder by pressing  PROGRAM.
On-screen sound program/surround decoder selection
a
Press ON SCREEN.
b
Use the cursor keys to select “Sound Program” and press 
ENTER.
c
Use the cursor keys to select a sound program/surround 
decoder and press ENTER.
 You can change the settings of the surround programs and surround decoders in  the “Sound Program” menu (p.103).
 The sound mode can be applied separately to each input source.
 You can check which speakers are currently outputting sound with the speaker  indicators on the front panel (p.10) or the “Audio Signal” screen in the 
“Information” menu (p.124).
Selecting the sound mode
2
3
5
1
46
TUN./ CH
ENHANCER
SUR.
DECODE
HDMI OUT
MEMORY
INFO AM
PA R T YFM
0
  10
LEVEL
ENT
SETUP
ZONE
8
7
SLEEP
9
SOURCE
RECEIVERAV
AUDIO
1
2
3
4
5
6
7
V- AU X
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B ]
[ A ]
CLASSICAL
LIVE
CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
INPUT
PURE
DIRECT
MUTE
TVSCENE
1
2
3
4
PROGRAM
VOLUME
TV VOLMUTE
MODETOP MENURETURN
DISPLAYPOP-UP/MENUTV CH
PRESET
ENTER
ON SCREEN
OPTIONTUN./ CH
SOURCERECEIVER
AVAUDIO
1
2
3
4
5
6
7
V-AUX
1
2
3
4
MULTI
PHONO
USB
NET
TUNER
DOCK
[ B]
[ A]
SUR.DECODE
ENHANCER SUR.DECODE
ENHANCERCLASSICAL
LIVE/CLUB
ENTERTAIN
MOVIE
STEREO
STRAIGHT
PURE DIRECTON SCREEN  ON SCREEN ENTER ENTER PROGRAMCursor keys