Xerox WorkCentre 4112 User Manual

							Product Overview
Xerox 4112/4127 Copier/Printer 1-13
System Administration Guide
Changing the Power Saver Mode time interval
To activate the Power Saver feature, set the Sleep Mode button to Enabled, and set the Low 
Power Mode and the Sleep Mode time intervals as follows:
Note
The amount of time that passes before the machine enters Low Power Mode and Sleep Mode 
can be specified in 1 minute increments, from 1 to 240 minutes for each mode.
1. Enter the System Administrator Mode (Chapter 1 Entering the System Administrator mode 
on page 1-10.)
2. Select System Settings and then select Common Settings. 
3. Select Machine Clock /Timers. 
Downloaded From ManualsPrinter.com Manuals 
						

							Product Overview
1-14   System Administration Guide
Xerox 4112/4127 Copier/Printer
4. Select Power Saver/Energy Saver, and select Change Settings. 
5. Using the up/down arrow buttons, configure a power saver mode migration time from 1 to 
240 minutes, in 1 minute increments.
a.From Last Selection to Low Power Mode:Set the time to move to the Low Power 
Mode after the last operation.
Note
The default for From Last Selection to Low Power Mode is 15 minutes. 
b.From Last Selection to Sleep Mode:Set the time to move to the Sleep Mode after 
the last operation.
Notes
The default for From Last Selection to Sleep Mode is 60 minutes. Configure the From Last 
Selection to Sleep Mode time to be longer than the From Last Selection to Low Power 
Mode time.
6. Press Save.
7. Select Close.
8. Exit the System Administrator Mode (Chapter 1 Exiting the System Administrator mode on 
page 1-11).
Downloaded From ManualsPrinter.com Manuals 
						

							Product Overview
Xerox 4112/4127 Copier/Printer 1-15
System Administration Guide
Exiting the Power Saver Mode
The following describes how to exit the Power Saver mode. The Power Saver mode is exited in 
the following instances:
• By pressing the Power Saver button
•Receiving Print Data
1. Press the Power Saver button.
Interface cables
When connecting to a network, use the Ethernet interface.
Using the Ethernet Interface
The Ethernet interface supports the following 2 types:
•100Base-TX
•10Base-T
This section describes the installation procedure for the Ethernet interface.
1. Confirm that the power switch is turned off.
2. Connect a network cable to the Ethernet interface connector.
Note
Prepare a network cable suitable for your network connection. When changing the network 
cable, consult the appropriate personnel.
3. Switch on the machine.
Power Saver 
button
Downloaded From ManualsPrinter.com Manuals 
						

							Product Overview
1-16   System Administration Guide
Xerox 4112/4127 Copier/Printer
Internal Fonts
The listed fonts are available as standard fonts on the machine: 
Stroke fonts (for PCL5 and 
HP-GL/2)European Stroke fonts
Outline 
fontsEuropean HP-GL/2Roman
Sans Serif
PDFArial
Arial Italic
Arial Bold
Arual
Bold Italic
Courier
Courier Italic
Courier BoldCourier Bold Italic
Symbol
Times New Roman
Times New Roman Bold 
Italic
ITC Zepf Dingbats
GoldSEMM
Gold SAMM
PCLCG Times
CG Times Italic
CG Times Bold
CG Times Bold Italic
Univers Medium
Univers Medium Italic
Univers Bold
Univers Bold Italic
Univers Medium Condensed
Univers Medium Condensed Italic
Univers Bold Condensed
Univers Bold Condensed Italic
Antique Olive
Antique Olive Italic
Antique Olive Bold
CG Omega
CG Omega Italic
CG Omega Bold
CG Omega Bold Italic
CG Omega Bold Italic
Garamond Antiqua
Garamond Kursiv
Garamond Halbfett
Garamond Kursiv Halbfett
(Default): Courier
Courier Italic
Courier Bold
Courier Bold Italic
Letter Gothic
Letter Gothic Italic
Letter Gothic BoldTimes New Bold
Times New Bold Italic
Symbol
Wingdings
Line Printer
Times Roman
Times Italic
Times Bold
Times Bold Italic
Helvetica
Helvetica Oblique
Helvetica Bold
Helvetica Bold Oblique
CourierPS
CourierPS Oblique
CourierPS Bold
CourierPS Bold Oblique
SymbolPS
Palatino Roman
Palatino Italic
Palatino Bold
Palatino Bold Italic
ITC Bookman Light
ITC Bookman Light Italic
ITC Bookman Demi
ITC Bookman Demi Italic
Helvetica Narrow
Helvetica Narrow Oblique
Helvetica Narrow Bold
Helvetica Narrow Bold 
Oblique
New Century Schoolbook 
Roman
Downloaded From ManualsPrinter.com Manuals 
						

							Product Overview
Xerox 4112/4127 Copier/Printer 1-17
System Administration Guide Outline 
fontsEuropean PCL 
continuedAlbertus Medium
Albertus Extra Bold
Clarendon Condensed
Coronet
Marigold
Arial
Arial Italic
Arial Bold
Arial Bold Italic
Times New
Times New ItalicNew Century 
Schoolbook Italic
New Century 
Schoolbook Bold
New Century 
Schoolbook Bold 
Italic
ITC Avant Garde 
Book
ITC Avant Garde 
Book Oblique
ITC Avant Garde 
Demi
ITC Avant Garde 
Demi Oblique
ITC Zapf Chancery 
Medium Italic
ITC Zapf Dingbats
KO PCL5Muyngio
Gothic
R- Gothic
Graphic
Kungso
SaemmulT-Myungio
T-Gothic
TR-Gothic
T-Graphic
T-Kungso
T-Saemmul
TC PC L 5Sou tail
Downloaded From ManualsPrinter.com Manuals 
						

							Product Overview
1-18   System Administration Guide
Xerox 4112/4127 Copier/Printer
Downloaded From ManualsPrinter.com Manuals 
						

							Xerox 4112/4127 Copier/Printer 2-1
System Administration Guide
2Configuration
TCP/IP (LPD/Port 9100)
Preparations
The following items are required when using TCP/IP (LPD/Port 9100) protocol on the machine.
• A network environment where TCP/IP can be used.
• The "CentreWare Utilities" CD-ROM, which is included with this product.
Configuration procedure
Overview
The machine can be connected to computers using TCP/IP (LPD/Port 9100) protocol.
The following is the procedure to use TCP/IP(LPD/Port 9100) protocol.
• Configuration on the Machine: Configure TCP/IP (LPD/Port 9100) on the machine.
• Configuration on the Computer: Install the print driver.
Configuration on the machine (LPD)
This section describes the configuration procedure to use TCP/IP (LPD/Port 9100) protocol on 
the machine. First enable the LPD Port or Port 9100 port, then assign the IP address.
LPR/LPD is a platform-independent printing protocol that runs over TCP/IP. LPD (or Line Printer 
Daemon) refers to the process that accepts print jobs from the line printer daemon client (LPR 
client). This is analogous to the printer software and is often called “LPD server.”
The print server waits for the client to send a job. A print server may be capable of handling 
multiple printers and print queues at once. Since it (usually) has a single IP address, the queue 
name must be used to specify the intended print queue.
Note
The configuration can also be performed using CentreWare Internet Services or CentreWare 
Utilities. Refer to “Using CentreWare Internet Services”.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration
2-2   System Administration Guide
Xerox 4112/4127 Copier/Printer
Note
Enable the SOAP port and the SNMP port in most cases.
1. Enter the System Administrator Mode (Chapter 1 Entering the System Administrator mode 
on page 1-10.)
2. Enable either the LPD port or the Port 9100 port as appropriate. In this example, the LPD 
port is enabled.
a. Select System Settings.
b. Select Connectivity & Network Setup.
c. Select Port Settings.
d. Select LPD and then select Change Settings.
e. Select LPD - Port Status and select Change Settings.
f. Select Enabled and then select Save.
g. Select Close repeatedly until the Connectivity & Network Setup screen is displayed
3. If necessary, set the IP Address (Chapter 1 Setting the IP address on page 1-11).
4. Exit the System Administrator Mode (Chapter 1 Exiting the System Administrator mode on 
page 1-11).
5. After the machine is restarted, print out the Printer Settings List to confirm that the LPD 
port is enabled.
Note
Configure the LPD as necessary. Refer to LPD on page 3-10 fo r t h e  L PD  c o nf ig ura t i on .  Al so  
if using Port 9100, configure as necessary. Refer to Port 9100 on page 3-15 fo r t h e  Por t  
9100 configuration.
Configuration on the computer
This section describes the configuration procedure for the computer.
• Install the print Driver.
Notes
• For information about the usable operating systems, refer to Supported operating systems 
on page 1-4.
• Refer to the manual contained in the “CentreWare Utilities” 
CD-ROM for the print driver installation procedure.
To print from a Macintosh using TCP/IP (LPD), refer to the manual contained in the CD-ROM 
included with this product for the print driver installation procedure.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration
Xerox 4112/4127 Copier/Printer 2-3
System Administration Guide
NetWare
Preparations
The following items are required when using NetWare network:
•A NetWare server.
• The "CentreWare Utilities" CD-ROM which is included with this product.
Configuration procedure
Overview
The machine supports PServer mode for both the NetWare Directory Service and Bindery 
Service. PServer mode enables the machine to function as a print server and to capture print 
jobs in the print queue to output. The printer created for the machine consumes one file server 
license.
Note
The machine does not support Remote Printer (RPrinter) Mode.
Supported interfaces
•100Base-TX
•10Base-T
Supported frame types
• Ethernet II specification
• IEEE802.3 specification
• IEEE802.3/IEEE802.2 specification
• IEEE802.3/IEEE802.2/SNAP specification
Note
The machine will send packets of each frame type on the network, and will initialize for the 
same frame type as the first reply packet received. However, if there are multiple protocols 
running on the same network, use Ethernet II specification.
Configuration on the machine (NetWare)
This section describes the configuration procedure to connect the machine to a NetWare 
network.
Note
Configuration can also be performed using the Network configuration tools included in 
CentreWare Internet Services or CentreWare Utilities. Refer to “Using CentreWare Internet 
Services”.
1. Confirm the device name and network address.
Print the Printer Settings List to confirm the device name and network address printed 
under the NetWare item.
2. Configure the machine using the “CentreWare Utilities” CD-ROM.
There is no need to activate the NetWare port on the machine prior to configuration when 
using the “CentreWare Utilities” CD-ROM.
Downloaded From ManualsPrinter.com Manuals 
						

							Configuration
2-4   System Administration Guide
Xerox 4112/4127 Copier/Printer
Note
Refer to the manual contained in the “CentreWare Utilities” CD-ROM for the configuration 
procedure.
Microsoft Network (SMB)
Preparations
The following items are required when using a Microsoft Network (SMB):
• Network environment where either TCP/IP or NetBEUI can be used.
• The "CentreWare Utilities" CD-ROM, which is included with this product.
Configuration procedure
Overview
The machine can be connected to computers using Microsoft Networks (SMB).
Depending on the network environment, the machine may need to be configured with an IP 
address, subnet mask and gateway address. Confirm with the network administrator and set up 
the necessary items.
The following is the procedure to connect the machine to a Microsoft Network (SMB):
• Configuration on the Machine: Enable the SMB port on the machine.
• Configuration on the Computer: Install the print driver.
Configuration on the machine (SMB)
This section describes the configuration procedure to connect the machine to Microsoft 
Networks (SMB). First enable the SMB port, then set the IP address.
Notes
• The configuration can also be performed using the IP configuration tools included in 
CentreWare Internet Services or CentreWare Utilities. Refer to “Using CentreWare Internet 
Services”.
• Enable the SOAP port and the SNMP port in most cases.
1. Enter the System Administrator Mode (Chapter 1 Entering the System Administrator mode 
on page 1-10.)
2. Enable the SMB port.
a. Select System Settings.
b. Select Connectivity & Network Setup.
c. Select Port Settings.
d. Select SMB and then select Change Settings.
e. Select Port Status and select Change Settings.
Downloaded From ManualsPrinter.com Manuals