Xerox Synergix 510dp User Manual

MEDIA
XEROX WIDE FORM AT 510dp OPERATOR MANUAL11
5.  Rotate the media roll to wind the end of the media onto the
roll.
6.  Lift the media roll out of the drawer.
7.  Lay the media roll on a flat, horizontal surface.
8.  Squeeze the lever at the end of the media roll support tube
and remove the tube from the media roll.
9.  Lay the new media roll on a flat, horizontal surface.
10.  Slide the end of the media roll support tube without the lever
into the new media roll as far as it will go.
Downloaded From...

MEDIA
12XEROX WIDE FORM AT 510dp OPERATOR MANUAL
11.  Squeeze the lever at the end of the media roll support tube
and position the tube until the size indicators on the tube
match the size of the roll.
•  For example, if the media roll is 36 inches, the ends of the
media roll should be at the 36-inch markers on the media
roll support tube.
12.  Place the new media roll into the media drawer so that the
lead edge of the paper is on the underside of the roll and
toward the printer.
13.  Position the media...

MEDIA
XEROX WIDE FORM AT 510dp OPERATOR MANUAL13
16.  Rotate the media roll to feed the media under the baffle and
beyond the registration window.
NOTE:  Ensure that the lead edge of the media is flat and is
not folded over itself.
17.  Squeeze the baffle release and lower the baffle until it locks in
place on both sides.
18.  Slowly rotate the media roll until the lead edge of the media is
centered in the registration window.
19.  Do one of the following:
•  If the drawer is a sealed media drawer, close...

MEDIA
14XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Changing the roll media size and type
Whenever you open a media drawer, the message display
prompts you to change the type or width of the media.  If you have
not changed the type or width of the roll media in the drawer, press
the Exit key.  If you have changed the type or width, you must
enter the new information.
To change the roll media size and type:
1. Press the Media key.  The message display indicates the
width and type of roll media last specified...

MEDIA
XEROX WIDE FORM AT 510dp OPERATOR MANUAL15
6. Press the Previous or Next key to scroll through the media
type selections.  The media type selections are BOND,
VELLUM, and FILM.
7.  When you scroll to the desired media type, press the Enter
key.
8.  Do one of the following:
• Press the Media key or the Exit key in order to save your
selections and return to the system prompt.
• Press the Enter key to return to the media size and type
selection process and change the selections you just
made....

MEDIA
16XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Using the cut sheet feed-in shelf
When the correct media size or type is not loaded in the printer,
you can bypass the media drawers and manually load cut sheets
into the printer.
If large size cut-sheet prints, portrait D-size (A1) oe E-size (A0),
are being made, return to the Printer and guide the lead edge of
the print as it exits the Printer to prevent the print from jamming at
the exit. With the Output Tray in the raised position, the prints
could...

MEDIA
XEROX WIDE FORM AT 510dp OPERATOR MANUAL17
Automatic media roll switching
The printer has an automatic roll-switching feature that allows it to
switch to another roll when the roll in use empties.  This feature
provides for longer continuous operation of the printer.
Automatic switching is possible only if the following conditions are
met:
•  The printer has more than one drawer.
•  Another drawer contains a media roll of the identical size and
type as the roll in use.
•  The print job has not...

MEDIA
18XEROX WIDE FORM AT 510dp OPERATOR MANUAL
This page has been intentionally left blank.
Downloaded From ManualsPrinter.com Manuals 

XEROX WIDE FORM AT 510dp OPERATOR MANUAL19
4. Off-line Setup Menu
The printer has an off-line Setup Menu that allows you to
customize the printer and the AccXES controller to meet your
particular requirements.
Setup Menu options
The Setup Menu has the following options:
• Utilities
• Setup I/O Ports
• Setup Printers
• Processing Defaults
• System Administration
• Printer Menu
Each of the Setup Menu options has a number of sub-options.
This chapter documents the Printer Menu option in detail.
For...

OFF-LINE SETUP MENU
20XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Printer Menu
The Printer Menu allows you to control the operation of the printer.
This menu contains six options.  The table below describes the
Printer Menu options and their sub-options.
Table 1. Printer Menu options
Option Sub-option Function
KEYPRESS Enables or disables an audible beeper when a
control panel key is pressed.
Settings: ON and OFF
Default: ONAUDIBLE INDICATORS
ALARM Enables or disables an audible beeper when
the printer...