Xerox Synergix 510dp User Manual

							MEDIA
XEROX WIDE FORM AT 510dp OPERATOR MANUAL11
5.  Rotate the media roll to wind the end of the media onto the
roll.
6.  Lift the media roll out of the drawer.
7.  Lay the media roll on a flat, horizontal surface.
8.  Squeeze the lever at the end of the media roll support tube
and remove the tube from the media roll.
9.  Lay the new media roll on a flat, horizontal surface.
10.  Slide the end of the media roll support tube without the lever
into the new media roll as far as it will go.
Downloaded From ManualsPrinter.com Manuals 
						

							MEDIA
12XEROX WIDE FORM AT 510dp OPERATOR MANUAL
11.  Squeeze the lever at the end of the media roll support tube
and position the tube until the size indicators on the tube
match the size of the roll.
•  For example, if the media roll is 36 inches, the ends of the
media roll should be at the 36-inch markers on the media
roll support tube.
12.  Place the new media roll into the media drawer so that the
lead edge of the paper is on the underside of the roll and
toward the printer.
13.  Position the media roll support tube so that the ends of the
tube rest within the support rollers at the sides of the drawer.
•  Ensure that the tube falls into place within the support
rollers.
14.  Remove the tape from the lead edge of the media roll.
15.  If the lead edge of the media roll contains debris from the
adhesive or is torn or uneven, trim the lead edge.
NOTE:  Trimming is not usually necessary for a new roll of
media.
Downloaded From ManualsPrinter.com Manuals 
						

							MEDIA
XEROX WIDE FORM AT 510dp OPERATOR MANUAL13
16.  Rotate the media roll to feed the media under the baffle and
beyond the registration window.
NOTE:  Ensure that the lead edge of the media is flat and is
not folded over itself.
17.  Squeeze the baffle release and lower the baffle until it locks in
place on both sides.
18.  Slowly rotate the media roll until the lead edge of the media is
centered in the registration window.
19.  Do one of the following:
•  If the drawer is a sealed media drawer, close the Plexiglas
cover.
•  If the drawer is not a sealed media drawer, proceed to
step 20.
20.  Close the roll media drawer.
21.  Lower the output tray.
22.  If the size or type of the new media roll is different from that of
the old media roll, you must specify the new size and type.
Refer to Changing the roll media size and type in this chapter
for instructions on entering the new roll media information.
Downloaded From ManualsPrinter.com Manuals 
						

							MEDIA
14XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Changing the roll media size and type
Whenever you open a media drawer, the message display
prompts you to change the type or width of the media.  If you have
not changed the type or width of the roll media in the drawer, press
the Exit key.  If you have changed the type or width, you must
enter the new information.
To change the roll media size and type:
1. Press the Media key.  The message display indicates the
width and type of roll media last specified for drawer 1.
NOTE:  The Media key is active from either on-line or off-line
mode.
2. Press the Previous or Next  key to scroll through the media
source selections.  The selections are ROLL1, ROLL2,
ROLL3, and BYPASS SHELF (cut sheet feed-in shelf).
3.  When you scroll to the media source you want to change,
press the Enter key.  The message display instructs you to
select the media width.  It indicates the current media width.
NOTE:  Media width does not apply to the BYPASS SHELF
selection.  If you have selected BYPASS SHELF as the media
source, the message display instructs you to select the media
type.  Proceed to step 6.
4. Press the Previous or Next key to scroll through the media
width selections.  The width selections are:
11.0 INCH 297 MM.
12.0 INCH 353 MM.
17.0 INCH 420 MM.
18.0 INCH 500 MM.
22.0 INCH 594 MM.
24.0 INCH 620 MM.
30.0 INCH 707 MM.
34.0 INCH 750 MM.
36.0 INCH 841 MM.
860 MM.
880 MM.
900 MM.
5.  When you scroll to the desired media width, press the Enter
key.  The message display instructs you to select the media
type.  It indicates the current media type.
Downloaded From ManualsPrinter.com Manuals 
						

							MEDIA
XEROX WIDE FORM AT 510dp OPERATOR MANUAL15
6. Press the Previous or Next key to scroll through the media
type selections.  The media type selections are BOND,
VELLUM, and FILM.
7.  When you scroll to the desired media type, press the Enter
key.
8.  Do one of the following:
• Press the Media key or the Exit key in order to save your
selections and return to the system prompt.
• Press the Enter key to return to the media size and type
selection process and change the selections you just
made.
Downloaded From ManualsPrinter.com Manuals 
						

							MEDIA
16XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Using the cut sheet feed-in shelf
When the correct media size or type is not loaded in the printer,
you can bypass the media drawers and manually load cut sheets
into the printer.
If large size cut-sheet prints, portrait D-size (A1) oe E-size (A0),
are being made, return to the Printer and guide the lead edge of
the print as it exits the Printer to prevent the print from jamming at
the exit. With the Output Tray in the raised position, the prints
could feed back into the Printer.
To manually feed cut sheets into the printer:
1.  Raise the output tray all the way until it rests on top of the
printer.
2.  Select the appropriate cut sheet for the print job.
NOTE:  The minimum size for a cut sheet is 8-1/2 x 11 inches
(216 x 279 mm) fed short edge lead.
3.  Set the BYPASS media type on the printer control panel to the
correct one for the print job.  See Changing the roll media
size and type for further information.
NOTE:  The printer will accept whatever media type you
manually feed into it, regardless of the media type you
specify.  You should ensure that the media type is correct,
however, as the printer uses the media type to determine
the fuser temperature.  The wrong fuser temperature could
cause poor print quality.  It could also result in a
maintenance service call, if any toner rubs off the media
onto the fuser roll.
4.  Center the media between the size indicators on the cut sheet
feed-in shelf.
5.  Feed the lead edge of the media squarely into the printer until
the printer grabs and advances the media.
6.  From the client workstation, specify Manual Feed as the media
source.
7.  Submit the print job.
8.  When you are finished manually feeding cut sheets, lower the
output tray.
Downloaded From ManualsPrinter.com Manuals 
						

							MEDIA
XEROX WIDE FORM AT 510dp OPERATOR MANUAL17
Automatic media roll switching
The printer has an automatic roll-switching feature that allows it to
switch to another roll when the roll in use empties.  This feature
provides for longer continuous operation of the printer.
Automatic switching is possible only if the following conditions are
met:
•  The printer has more than one drawer.
•  Another drawer contains a media roll of the identical size and
type as the roll in use.
•  The print job has not specified a particular roll (e.g., roll 1).
If both of the remaining media drawers contain the identical media
size and type as the roll is in use, the printer will select the lowest
numbered drawer first.  If, for example, roll 3 empties and both roll
1 and roll 2 contain the same media size and type, the printer will
switch to roll 1.  If roll 1 empties, the printer will switch to roll 2.
Media storage tips
To obtain maximum results from your print media, follow these
media storage tips:
•  Store cut sheet media flat, not on edge, in a closed cut sheet
media package.
•  Store roll media on end in an appropriately sealed media bag.
•  Store the media in a cool dry environment.
Downloaded From ManualsPrinter.com Manuals 
						

							MEDIA
18XEROX WIDE FORM AT 510dp OPERATOR MANUAL
This page has been intentionally left blank.
Downloaded From ManualsPrinter.com Manuals 
						

							XEROX WIDE FORM AT 510dp OPERATOR MANUAL19
4. Off-line Setup Menu
The printer has an off-line Setup Menu that allows you to
customize the printer and the AccXES controller to meet your
particular requirements.
Setup Menu options
The Setup Menu has the following options:
• Utilities
• Setup I/O Ports
• Setup Printers
• Processing Defaults
• System Administration
• Printer Menu
Each of the Setup Menu options has a number of sub-options.
This chapter documents the Printer Menu option in detail.
For information about the remaining Setup Menu options, refer to
the XES Synergix 8825/8830/8850/510dp Controller Setup Manual
for Firmware 9.0 or the Web Printer Manager Tool User Guide.
Downloaded From ManualsPrinter.com Manuals 
						

							OFF-LINE SETUP MENU
20XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Printer Menu
The Printer Menu allows you to control the operation of the printer.
This menu contains six options.  The table below describes the
Printer Menu options and their sub-options.
Table 1. Printer Menu options
Option Sub-option Function
KEYPRESS Enables or disables an audible beeper when a
control panel key is pressed.
Settings: ON and OFF
Default: ONAUDIBLE INDICATORS
ALARM Enables or disables an audible beeper when
the printer experiences a condition requiring
immediate attention.
Settings: ON and OFF
Default: ON
READY TO POW ER SAVER Controls the length of time the printer will
remain idle before entering power saver
mode.
Settings: 5 to 50 minutes in 5-minute intervals
Default: 50 minutes
NOTE:  A value of 0 prevents the printer from
entering power saver mode.TIMERS
POW ER SAVER TO REST Controls the length of time the printer will
remain idle in power saver mode before
entering rest mode.
Settings: 15 to 150 minutes in 15-minute
intervals
Default: 150 minutes
NOTE:  A value of 0 prevents the printer from
entering rest mode.
PRINTER ADJUSTMENTS DENSITY Increases or decreases the print density.
Settings: 0 (lightest) to 10 (darkest)
Default: 5
FINISHER SETTINGS FINISHER CONFIG TYPE Specifies the folder configuration type.
Settings: NONE (no finisher) and 003
(Generic Finisher Interface)
Default: NONE
Downloaded From ManualsPrinter.com Manuals