Xerox Synergix 510dp User Manual

							OFF-LINE SETUP MENU
XEROX WIDE FORM AT 510dp OPERATOR MANUAL21
Table 1.  Printer Menu options (continued)
Option Sub-option Function
TEST PLOT Allows you to run a test print in off-line mode
from each media source.  The selections are
ROLL 1, ROLL 2, ROLL 3, and BYPASS.
PRINTER DIAGNOSTICS Reserved for use by the service
representative and is password protected.
DIAGNOSTICS
RECENT FAULT LOG Displays a record of the last 99 printer faults.
You may be asked to provide information from
this log when placing a call for service.
METER A Provides a record of the total number of
square feet/meters of prints produced.  This
number is useful for both billing and service
purposes.BILLING METERS
METER B Provides a record of the total number of linear
feet/meters of prints produced.  This number
is useful for both billing and service purposes.
Downloaded From ManualsPrinter.com Manuals 
						

							OFF-LINE SETUP MENU
22XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Accessing the Printer Menu
Note: If there is a Scanner connected, the message displayed will
be SYNERGIX CS 510dp.  If there is no Scanner connected the
message will be SYNERGIX PS 510dp.
To access the Printer Menu:
1. Press the On-line/Off-line key to enter off-line mode.
•  The on-line/off-line indicator will go out.
•  The display will indicate  SYNERGIX CS 510dp PAUSED
or SYNERGIX PS 510dp.
2. Press the Enter key to access the SYNERGIX CS 510dp or
SYNERGIX PS 510dp SETUP MENU.
3. Press the Previous or Next key until  is
displayed.
4. Press the Enter key to access the PRINTER MENU.
•  The display will indicate PRINTER MENU .  This is the first PRINTER MENU option.
Enabling or disabling the audible indicators
Note: If there is a Scanner connected, the message displayed will
be SYNERGIX CS 510dp.  If there is no Scanner connected the
message will be SYNERGIX PS 510dp.
To enable or disable the Audible Indicators:
1. Access the PRINTER MENU.  See Accessing the Printer
Menu in this chapter.
2. Press the Enter key to select AUDIBLE INDICATORS.  The
current setting for the KEYPRESS option is displayed.
3.  Do one of the following:
•  To select the KEYPRESS option, press the Enter key.
•  To select the ALARM option:
-  Navigate to it by pressing the Previous or Next  key.
The current setting for the ALARM option is displayed.
- Press the Enter key to select the option.
4. Press the Previous or Next key to switch between ON and
OFF.
5. Press the Enter key to save your selection.
6. Press the On-line/Off-line key to return to on-line mode.
•  The on-line/off-line indicator will light.
•  The display will indicate  SYNERGIX CS 510dp IDLE or
SYNERGIX PS 510dp.
Downloaded From ManualsPrinter.com Manuals 
						

							OFF-LINE SETUP MENU
XEROX WIDE FORM AT 510dp OPERATOR MANUAL23
Setting the timers
To set the Power Saver mode and Rest mode timers:
1.  Access the PRINTER MENU.  See Accessing the Printer
Menu in this chapter.
2. Press the Previous or Next key until TIMERS is displayed.
3. Press the Enter key to select TIMERS.  The current setting for
the READY TO POW ER SAVER option is displayed.
4.  Do one of the following:
•  To select the READY TO POWER SAVER option, press
the Enter key.
•  To select the POW ER SAVER TO REST option:
-  Navigate to it by pressing the Previous or Next key.
- Press the Enter key to select the option.
5. Press the Previous or Next key to scroll through the range of
values.
6.  When you scroll to the desired value, press the Enter key to
save your selection.
7. Press the On-line/Off-line key to return to on-line mode.
•  The on-line/off-line indicator will light.
•  The display will indicate  SYNERGIX CS 510dp IDLE or
SYNERGIX PS 510dp.
Adjusting the print density
Note: If there is a Scanner connected, the message displayed will
be SYNERGIX CS 510dp.  If there is no Scanner connected the
message will be SYNERGIX PS 510dp.
To adjust the print density:
1.  Access the PRINTER MENU.  See Accessing the Printer
Menu in this chapter.
2. Press the Previous or Next key until PRINTER
ADJUSTMENTS is displayed.
3. Press the Enter key to select PRINTER ADJUSTMENTS.  The
current setting for the DENSITY option is displayed.
4. Press the Enter key to select DENSITY.
5. Press the Previous or Next key to scroll through the range of
values.
6.  When you scroll to the desired value, press the Enter key to
save your selection.
7. Press the On-line/Off-line key to return to on-line mode.
•  The on-line/off-line indicator will light.
•  The display will indicate  SYNERGIX CS 510dp IDLE or
SYNERGIX PS 510dp
Downloaded From ManualsPrinter.com Manuals 
						

							OFF-LINE SETUP MENU
24XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Specifying the finisher configuration type
Note: If there is a Scanner connected, the message displayed will
be SYNERGIX CS 510dp.  If there is no Scanner connected the
message will be SYNERGIX PS 510dp.
To specify the finisher configuration type:
1. Access the PRINTER MENU.  See Accessing the Printer
Menu in this chapter.
2. Press the Previous or Next key until FINISHER SETTINGS is
displayed.
3. Press the Enter key to select FINISHER SETTINGS.
4. Press the Enter key to select FINISHER CONFIG TYPE.  The
current value for the FINISHER CONFIG TYPE option is
displayed.
5. Press the Previous or Next key to switch between NONE and
003.
6. Press the Enter key to save your selection.
7. Press the On-line/Off-line key to return to on-line mode.
•  The on-line/off-line indicator will light.
•  The display will indicate  SYNERGIX CS 510dp IDLE or
SYNERGIX PS 510dp
Performing printer diagnostics
The DIAGNOSTICS option has two operator-accessible sub-
options – TEST PLOT and RECENT FAULT LOG.
NOTE:  A third DIAGNOSTICS option, PRINTER DIAGNOSTICS,
is restricted to the service representative.  If you select it, you will
be asked to enter a password.  Press the Exit key to exit the
option.
Printing a test plot
Note: If there is a Scanner connected, the message displayed will
be SYNERGIX CS 510dp.  If there is no Scanner connected the
message will be SYNERGIX PS 510dp.
To print a test plot:
1. Access the PRINTER MENU.  See Accessing the Printer
Menu in this chapter.
2. Press the Previous or Next key until DIAGNOSTICS is
displayed.
3. Press the Enter key to select DIAGNOSTICS.
4. Press the Enter key to select TEST PLOT.
5. Press the Previous or Next key to scroll through the media
sources.
6. Press the Enter key to select the media source.  The printer
will initialize the media supply and print the test plot.
7. Press the On-line/Off-line key to return to on-line mode.
•  The on-line/off-line indicator will light.
Downloaded From ManualsPrinter.com Manuals 
						

							OFF-LINE SETUP MENU
XEROX WIDE FORM AT 510dp OPERATOR MANUAL25
•  The display will indicate  SYNERGIX CS 510dp IDLE or
SYNERGIX PS 510dp
Viewing the recent fault log
Note: If there is a Scanner connected, the message displayed will
be SYNERGIX CS 510dp.  If there is no Scanner connected the
message will be SYNERGIX PS 510dp.
To view the recent fault:
1. Access the PRINTER MENU.  See Accessing the Printer
Menu in this chapter.
2. Press the Previous or Next key until DIAGNOSTICS is
displayed.
3. Press the Enter key to select DIAGNOSTICS.
4. Press the Previous or Next key until RECENT FAULT LOG is
displayed.
5. Press the Enter key to select RECENT FAULT LOG.
6. Press the Next key to display the two most recent faults.
7. Press the Previous or Next key to scroll through the fault
listing.
8.  When you are finished viewing the fault listing, press the On-
line/Off-line key to return to on-line mode.
•  The on-line/off-line indicator will light.
•  The display will indicate  SYNERGIX CS 510dp IDLE or
SYNERGIX PS 510dp
Displaying the billing meter counts
Note: If there is a Scanner connected, the message displayed will
be SYNERGIX CS 510dp.  If there is no Scanner connected the
message will be SYNERGIX PS 510dp.
To display the billing meter counts:
1. Access the PRINTER MENU.  See Accessing the Printer
Menu in this chapter.
2. Press the Previous or Next key until BILLING METERS is
displayed.
3. Press the Enter key to select BILLING METERS.  The value
for METER A is displayed.  METER A provides the square
footage of prints produced.
4.  To view the value for METER B, press the Previous or Next
key.  METER B provides the linear feet of media produced.
5.  When you are finished viewing the meter counts, press the
On-line/Off-line key to return to on-line mode.
•  The on-line/off-line indicator will light.
•  The display will indicate  SYNERGIX CS 510dp IDLE or
SYNERGIX PS 510dp
Downloaded From ManualsPrinter.com Manuals 
						

							OFF-LINE SETUP MENU
26XEROX WIDE FORM AT 510dp OPERATOR MANUAL
This page has been intentionally left blank.
Downloaded From ManualsPrinter.com Manuals 
						

							XEROX WIDE FORM AT 510dp OPERATOR MANUAL27
5. Care
The printer requires a minimum of operator maintenance.  You will
need to replace the toner cartridge and toner waste bottle when
the cartridge empties.  You also will need to clean the outside
surface of the printer when necessary.
This chapter provides the procedures for performing the required
tasks and for ordering supplies.
When the toner cartridge needs replacement
When the toner cartridge is empty, the following occur:
•  The toner supply access cover indicator on the graphic display
flashes.
•  The alarm beep (if enabled) sounds.
•  A J1.01 status code and a message instructing you to replace
the dry ink cartridge and waste bottle appear in the message
display.
To replace the toner cartridge and toner waste bottle, follow the
instructions in the Replacing the toner cartridge and Replacing
the toner waste bottle sections of this chapter.
Downloaded From ManualsPrinter.com Manuals 
						

							CARE
28XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Replacing the toner cartridge
To replace the toner cartridge:
CAUTION:  Toner identified for use in the XEROX Wide Format
510dp is a two-component material made specifically for this
printer.  Use of toner not identified for the XEROX Wide Format
510dp will damage the printer.
1.  Open the replacement toner carton.
•  Remove the replacement toner cartridge.
•  Remove the replacement toner waste bottle.
•  Save all the replacement toner packaging for recycling the
used toner cartridge and toner waste bottle.
2.  Open the toner supply access cover.
3.  Slide the gold cartridge dispenser patch cover to the left to
expose the dispenser patch.
4.  Pull the plunger to the right and lift the front end of the toner
cartridge.
5.  Release the plunger and rest the cartridge on the plunger
mechanism.
Downloaded From ManualsPrinter.com Manuals 
						

							CARE
XEROX WIDE FORM AT 510dp OPERATOR MANUAL29
6.  Carefully lift the used toner cartridge out of the printer.
•  Try not to tilt the cartridge too much to avoid toner
spillage.
7.  Wipe any excess toner off the used toner cartridge.
8.  Seal the used toner cartridge dispenser patch with tape.
9.  Place the used toner cartridge in the empty replacement toner
carton.
•  Do not seal the carton until you have added the toner
waste bottle to it as well.  Recycle the used cartridge and
waste bottle according to the instructions provided with the
replacement carton.
10.  Hold the new toner cartridge horizontally and shake it side to
side 10 or 12 times.
11.  Install the new toner cartridge so that the end containing the
cover tape is toward the front of the printer.
•  Ensure that the cover tape is facing up.
Downloaded From ManualsPrinter.com Manuals 
						

							CARE
30XEROX WIDE FORM AT 510dp OPERATOR MANUAL
12.  Lower the toner cartridge into position while pushing the
plunger to the left.
13.  Release the plunger.
14.  Rotate the toner cartridge back and forth until the cartridge
locks into position.
CAUTION:  Remove the cover tape carefully.  Do not remove the
clear, perforated seal.
15.  Remove the cover tape from the toner cartridge.
•  Do not remove the seal under the tape.
16.  Slide the gold cartridge dispenser patch cover to the right to
conceal the cartridge patch.
•  Ensure that the cartridge patch is completely covered.
17.  Close the toner supply access cover.
Downloaded From ManualsPrinter.com Manuals