Xerox Synergix 510dp User Manual

CARE
XEROX WIDE FORM AT 510dp OPERATOR MANUAL31
Replacing the toner waste bottle
Each time you replace the toner cartridge, you must replace the
toner waste bottle as well.
To replace the toner waste bottle:
1.  Open the front door.
.
Downloaded From ManualsPrinter.com Manuals 

CARE
32XEROX WIDE FORM AT 510dp OPERATOR MANUAL
CAUTION:  Pull the toner waste bottle out gently to avoid spillage
of toner.
2.  Carefully remove the toner waste bottle.
•  Pull the waste bottle forward until it disengages from the
mounting bracket.
.
3.  Remove the stopper from the side of the used toner waste
bottle.
Downloaded From ManualsPrinter.com Manuals 

CARE
XEROX WIDE FORM AT 510dp OPERATOR MANUAL33
CAUTION:  Ensure that the stopper is firmly in place to avoid
spillage of toner.
4.  Snap the stopper into place on the top of the used toner waste
bottle.
5.  Remove the stopper from the top of the new toner waste
bottle.
6.  Snap the stopper into place on the front of the new toner
waste bottle.
7.  Slide the new toner waste bottle onto the mounting bracket.
•  Push the bottle forward until you feel it snap into place.
8.  Close the front door.
CAUTION:...

CARE
34XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Cleaning the printer surface
As needed, clean the outside surfaces of the printer.  Use a clean
cloth dampened with mild soap and water.  Do not pour or spray
liquid directly on any part of the printer.
Downloaded From ManualsPrinter.com Manuals 

CARE
XEROX WIDE FORM AT 510dp OPERATOR MANUAL35
Ordering supplies
This section provides information for obtaining supplies for your
printer.
Supply order list
The XEROX Wide Format 510dp uses the following supplies:
•  Toner cartridge and toner waste bottle:
The printer is shipped with one toner cartridge and one toner
waste bottle.  Each time the toner cartridge empties, you must
replace both the cartridge and the waste bottle.  The two items
are packaged together as one part number.  When ordering,
use...

CARE
36XEROX WIDE FORM AT 510dp OPERATOR MANUAL
This page intentionally left blank
Downloaded From ManualsPrinter.com Manuals 

XEROX WIDE FORM AT 510dp OPERATOR MANUAL37
6. Problem solving
This chapter provides information for resolving various problems
that can occur during the operation of the printer.  It contains
instructions for clearing media jams.  It also includes status code
and error message tables, as well as a general problem-solving
table.  If you are unable to resolve the problem, follow the
procedure for calling for service at the end of the chapter.
Clearing media jams
When the printer experiences a media jam,...

PROBLEM SOLVING
38XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Fuser area jam
To clear a jam in the fuser area:
1.  Raise the output tray all the way so that it rests on top of the
printer.
WARNING:  Do not touch the fuser roll while clearing media jams
in the fuser area.  The fuser roll is very hot and can cause severe
burns.
2.  Open the fuser drawer all the way.
3.  Do one of the following:
•  Pull the jammed media out the back of the fuser area.  Go
to step 7.
•  If you cannot pull the jammed media out...

PROBLEM SOLVING
XEROX WIDE FORM AT 510dp OPERATOR MANUAL39
4.  Lift the inside latches on each side of the fuser drawer front
and lower the fuser drawer front.
5.  Hold the drawer front all the way open and pull the jammed
media out of the back of the fuser area.
6.  Close the fuser drawer front.
•  Ensure that it latches.
7.  Close the fuser drawer.
Downloaded From ManualsPrinter.com Manuals 

PROBLEM SOLVING
40XEROX WIDE FORM AT 510dp OPERATOR MANUAL
Cutter area jam
To clear a jam in the cutter area:
WARNING:  The cutter blade is very sharp.  Do not touch the
cutter blade when clearing media jams in the cutter area.
1.  Squeeze the latches on the cut sheet feed-in drawer and open
the drawer all the way.
2.  Pull the media out of the cutter area.
3.  Close the cutter drawer.
Downloaded From ManualsPrinter.com Manuals