Xerox Phaser 3435DN User Manual

9.10   
Half the page 
is blank.The page layout 
is too complex.Simplify the page layout and 
remove any unnecessary 
graphics from the document.
Install more memory in your 
printer. See page 10.1.
The page 
orientation setting 
may be incorrect.Change the page orientation in 
your application. See the 
Software Section.
The paper size 
and the paper 
size settings do 
not match.Ensure that the paper size in 
the printer driver settings 
matches the paper in the tray.
Or, ensure that the paper size 
in...

9.11   
Solving print quality problems
Dirt inside of the printer or improper paper loading may reduce print 
quality. See the table below to troubleshoot problems. 
ConditionSuggested solutions
Light or faded 
printIf a vertical white streak or faded area appears on 
the page:
• The toner supply is low. You may be able to 
temporarily extend the print cartridge life. See 
page 8.3. If this does not improve print quality, 
install a new print cartridge.
• The paper may not meet paper specifications 
(for...

9.12   
Background 
scatterBackground scatter results from bits of toner 
distributed on the printed page. 
• The paper may be too damp. Try printing with a 
different batch of paper. Do not open packages 
of paper until necessary so that the paper does 
not absorb too much moisture.
• If background scatter occurs on an envelope, 
change the printing layout to avoid printing over 
areas that have overlapping seams on the reverse 
side. Printing on seams can cause problems.
• If background scatter covers...

9.13   
Common Windows problems
Note
Refer to Microsoft Windows 2000/XP/2003 User’s Guide that 
came with your PC for further information on Windows error 
messages. Curl
If the printed paper is curled or paper does not 
feed into the printer:
• Turn over the stack of paper in the tray. Also try 
rotating the paper 180° in the tray.
• Try printing to rear cover.
An unknown 
image 
repetitively 
appears on a 
next few sheets 
or loose toner, 
light print, or 
contamination 
occurs.Your printer is probably...

9.14   
Common Linux problems
ConditionSuggested solutions
The printer doesn’t 
print.• Check if the printer driver is installed in your 
system. Open Unified Driver Configurator 
and switch to the Printers tab in Printers 
configuration window to look at the list of 
available printers. Make sure that your 
machine is displayed on the list. If not, 
please, invoke Add new printer wizard to set 
up your device. 
• Check if the printer is started. Open Printers 
configuration and select your machine on...

10.1   
10 Installing accessories
Your printer is a full-featured laser printer that has been optimized to 
meet most of your printing needs. Recognizing that each user may have 
different requirements, however, Xerox makes several accessories 
available to enhance the printer’s capabilities.
This chapter includes:
• Precautions when installing accessories
• Installing a memory DIMM
Precautions when installing accessories
Disconnect the power cord: 
Never remove the control board cover while the power is...

10.2   
5Holding the memory DIMM by the edges, align the notches on the 
memory DIMM with the grooves on the memory DIMM slot.
6Push the DIMM straight into the DIMM slot until it snaps into place. 
Make sure the latches fit over the notches located on either side of 
the DIMM.
7Replace the control board cover.
8Reconnect the power cord and printer cable, and turn the printer 
on.Setting the memory in the PostScript printer 
properties
After installing the memory DIMM, you need to select it in the printer...

11.1   
11 Specifications
This chapter includes:
• Printer specifications
Printer specifications
ItemSpecifications and Description
Model name
Phaser 3435/DN
Printing speed
a33 ppm (A4); 35 ppm (Letter)
Duplex: 17 ipm (A4); 17.5 ipm (Letter)
Resolution
Up to 1200 x 1200 dpi effective output
Warm-up time
Less than 15 seconds
First print out time
Standby mode: 8.5 seconds 
Sleep mode: 25 seconds
Power rating
110 - 127 VAC or 220 - 240 VAC
See the Rating label on the machine for the 
correct voltage,...

1
INDEX
A
accessories
installing
memory DIMM 10.1
order information 7.1
C
cleaning
drum 8.2
inside 8.1
outside 8.1
cleaning sheet, print 8.2
component location 1.2
control panel
menus 2.1
status LED 1.4
D
demo page, print 2.7
DIMM, install 10.1
display language, change
control panel 2.7
drum, clean 8.2
E
error messages 9.6
H
high altitude 9.13
I
installing accessories
memory 10.1
J
jam, clear 9.1
L
Linux problems 9.14
loading paper
multi-purpose tray 5.6
tray 1/optional tray 2 5.5
M
Macintosh problems...

2
Windows 3.2
T
toner save mode, use 2.7
W
Windows problems 9.13
Downloaded From ManualsPrinter.com Manuals