Xerox DocuPrint 4590 EPS User Manual

Xerox 4590 EPS/4110 EPS User Guide
2-11
2. Paper and other media
CAUTION:For paper heavier than 256 gsm, slide both Paper 
Weight Switches to the heavier weight position (257 - 300 gsm). 
Failure to do so may result in paper jams.
5.Move both Paper Weight Switches to their appropriate 
positions.
6.Push the tray in gently until it comes to a stop.
NOTE:When the loaded tray is closed, the tray position is 
automatically adjusted in the front/back direction based on the 
paper size.
Downloaded From...

Xerox 4590 EPS/4110 EPS User Guide
2-12
2. Paper and other media
Load paper in the optional Tray 8 (post-process inserter)
The Post-Process Inserter is meant for loading paper (blank, 
copied paper, and so forth) to be used as separators and covers. 
Media loaded here will not be used to make copies.
NOTE:When adding paper to the Post-Process Inserter, remove 
any paper remaining in the tray, add it to the stack of paper 
to be added, then load all of the paper into the 
Post-Process Inserter at once....

Xerox 4590 EPS/4110 EPS User Guide
2-13
2. Paper and other media
Load tab paper
Load tab paper in trays 3 and 4
1.Pull out the tray towards you until it stops.
WARNING:When pulling out the paper tray, do it slowly. If 
pulled out with too much force, the tray can hit and injure your 
knees.
2.Load and align the edge of the tab paper against the right 
edge of the tray with the side to be printed on facing down.
3.Move the two paper guide levers while holding their grips so 
that they lightly contact the...

Xerox 4590 EPS/4110 EPS User Guide
2-14
2. Paper and other media
Load tab paper in Tray 5 (Bypass)
1.Open Tray 5 (Bypass). 
NOTE:If necessary, extend the extension flap. The extension flap 
can be extended in two stages. When pulling out the 
extension flap, do it gently.
2.Hold the center of the paper guides and slide them to the 
desired paper size.
3.Place the paper with the side to be printed facing up and the 
bottom side to be fed first. Insert the paper slowly to the end 
along the paper guide....

Xerox 4590 EPS/4110 EPS User Guide
2-15
2. Paper and other media
Load tab paper in Tray 8 (Post-process inserter)
1.Hold the center of the paper guides and slide them to the 
desired paper size.
2.If the paper in already printed on, load the paper with the 
printed side facing up and with the tab side to be fed first.
A
A
Downloaded From ManualsPrinter.com Manuals 

Xerox 4590 EPS/4110 EPS User Guide
2-16
2. Paper and other media
Change the size of paper trays
NOTE:If you need to change the paper size for trays 1 and 2, 
contact the Customer Support Center. 
Paper tray attributes are configurable and should match 
the attributes of the paper to be loaded to maintain high 
print quality.
Normally, plain paper is set. When changing the setting to 
a different paper quality, change the paper quality settings 
to match the type of paper to be loaded to maintain high...

Xerox 4590 EPS/4110 EPS User Guide
2-17
2. Paper and other media
3.While pressing the paper guide lever (2 paper guides), adjust 
the paper guide to match the size of your paper.
4.Check that the paper guides fit correctly in the slots and 
release the paper guide lever.
5.Load and align the edge of the paper against the left side of 
the tray. 
NOTE:Make sure that the paper guides are adjusted to the paper 
being used.
6.Gently push the tray in until it comes to a stop. 
NOTE:Affix the paper size label...

Xerox 4590 EPS/4110 EPS User Guide
2-18
2. Paper and other media
Change the size in the optional Trays 6 and 7 (HCF)
NOTE:When changing the paper size to non-standard size 
loaded in trays 6 and 7, contact your Customer Support 
Center. If doing so, it never returns to the original setting.
1.Pull out the tray towards you until it stops.
WARNING:When pulling out the paper tray, do it slowly. If 
pulled out with too much force, the tray can hit and injure your 
knees.
2.Remove any paper loaded on the...

Xerox 4590 EPS/4110 EPS User Guide
2-19
2. Paper and other media
5.Load and align the edge of the paper against the right edge of 
the tray with the side to be printed on facing up.
KEY POINT:Do not load paper exceeding the maximum fill line. 
Doing so might cause paper jams or machine trouble.
6.Push the tray in gently until it comes to a stop.
NOTE:Affix the paper size label to the front of the paper tray.
Change the paper size in the optional OHCF (Tray 6) 
1.Pull out the tray towards you until it...

Xerox 4590 EPS/4110 EPS User Guide
2-20
2. Paper and other media
4.Load and align the paper stack in the lower right corner of 
the tray as shown below. 
NOTE:Do not load paper exceeding the maximum fill line. Doing 
so might cause paper jams or machine malfunctions.
5.Slide both paper guides to just touch the edges of the paper 
stack. 
NOTE:Position the paper guides correctly to match the paper 
size. If the position of the paper guide is not correct, the paper 
may not be fed properly and paper jams...