Xerox Document Centre 545DC HCF User Manual

Connectivity & Network Setup
149
Tools
5
Important •Do not use the numbers assigned to the other ports.
Note • You cannot select [Port Number], if HTTP port is disabled.
To configure [Port Number], enable port status and reboot the machine, and then configure 
[Port Number].
SOAP
„Port Status
Select [Enabled] when you use an application program such as EasyOperator. 
„Port Number Enter a port number for SOAP from 1 to 65535.
The default value is 80.
Important • Do not use the numbers assigned to the...

5 Tools
150
Tools
5
„100 Mbps Half-DuplexSelect this to set 100BASE-TX (Half Duplex) as the default value. 
„10 Mbps Full-Duplex Select this to set 10BASE-T (Full Duplex) as the default value. 
„10 Mbps Half-Duplex Select this to set 10BASE-T (Half Duplex) as the default value. 
„1000 Mbps Select this to set 1000BASE-T as the default value.
Note • Gigabit Ethernet Kit (optional) is required for using 1000BASE-T.
„Gigabit Ethernet (GbE) Port
Select this check box to use Gibabit Ethernet Port.
Note • The...

Connectivity & Network Setup
151
Tools
5
IPv4 - Subnet Mask
Enter the subnet mask using the keyboard displayed or the numeric keypad when selecting 
[STATIC] at [IPv4 - IP Address Resolution].
Note •Enter the address in the format xxx.xxx.xxx.xxx, where xxx is a numeric value from of 0 to 
255.
• Specify a subnet mask using numbers (0 to 9) and periods (.). If you mistyped a character on 
the screen, select [Backspace] to delete the character.
IPv4 - Gateway Address
Enter the gateway address using the...

5 Tools
152
Tools
5
Manually Configured IPv6 Gateway
This setting is configurable when [Manually Configured IPv6 Address] is set. Specify a 
gateway address.
Note •Enter the address in the format xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx, where xxxx is a 
hexadecimal value.
IPv6 - DNS Server Setup
Set the DNS server for IPv6.
„Get IP Address from DHCP Set whether or not to automatically obtain the address of the DNS server from the DHCP 
server.
„DNS Server IP Address When [Get IP Address from DHCP] is set...

Connectivity & Network Setup
153
Tools
5
„When receiving E-mails via POP3 Enter the POP user name (on the left side of @) and incoming POP3 mail server name in the 
address section (on the right side of @). You can set an alias, such as 
[email protected]. 
For Example: [email protected] 
zAccount name: mymail 
Machine Name
Enter the machine name with up to 32 single-byte characters.
Host Name
Enter the host name with up to 16 single-byte characters.
Domain Name
Enter the domain name with up to...

5 Tools
154
Tools
5
HTTPS Proxy Server Name
Enter the HTTPS proxy server name or the IP address. Up to 255 characters are allowed. 
You can specify the addresses by IPv4 address, IPv6 address, and FQDN.
HTTPS Proxy Server Port Number
Set the HTTPS proxy server port number from 1 to 65535.
The default value is 8080.
Important • Do not use the numbers assigned to the other ports.
HTTPS Proxy Server Authentication
Select [Enabled] when authentication is requir ed to connect to the HTTPS proxy server.
HTTPS...

Connectivity & Network Setup
155
Tools
5
HTTP Proxy Server Name
Enter the server name or IP address of the HTTP proxy server. Up to 255 characters are
allowed. You can specify the addresses by IPv4 address, IPv6 address, and FQDN.
HTTP Proxy Server Port Number
Set the HTTP proxy server port number from 1 to 65535.
The default value is 8080.
Important •Do not use the numbers assigned to the other ports.
HTTP Proxy Server Authentication
Select [Enabled] when authentication is requir ed to connect to the...

5 Tools
156
Tools
5
SIP Settings
Configure the settings for a SIP User ID, SIP server to go through, and VoIP gateway. 
In [SIP Settings], you can set the following items.
SIP User ID (Sign-in Name)
Enter the SIP user name of the machine.
For example: [email protected]
The left side of @ (111 in this example) is called the SIP user name.
Note • If you do not use a SIP server, specify the IP address of the machine on the right side of 
@.
• When you use a SIP server manufactured by Cisco Systems. Inc, for...

Connectivity & Network Setup
157
Tools
5
„Primary Server IP AddressEnter the IP address of the primary server. Up  to 255 characters are allowed. You can specify 
the addresses by IPv4 address, IPv6 address, and FQDN.
„Primary Server - Port Number Set the port number of the primary server. Set the primary server port number from 1 to 
65535. The default value is 5060.
„Primary Server - Login User Name Enter the login user name of the primary server. Up to 31 characters are allowed.
„Primary Server -...

5 Tools
158
Tools
5
„Secondary Server - Login PasswordEnter the login password of the secondary server. Up to 31 characters are allowed.
„Secondary Server Type Select the type of secondary server from [Standard] or [Cisco].
VoIP Gateway Setup
You can configure the following settings for VoIP Gateway 1 to 50.
You can also configure different VoIP gateways by a recipient’s telephone number.
Note • To use fixed VoIP gateway,  do not register the ID, and specify only the IP address for VoIP 
Gateway 1.
• You...