Vodavi Starplus Dhs Installation Manual

“ADP” jack. When 
wired at the MDF 
the second pair of 
the telephone line 
cord/cable will 
activate this jack for 
any analog device 
function. This jack 
and wiring is 
completely 
independant of the 
key telephone 
operation and may 
be used for system 
resources or direct 
Central Office 
connections. 
Refer to the following diagram for modular jack locations: 
f-. ,,, 
Each key telephone has two modular jack connectors on the underside of the instrument. Both are located 
in a recessed connector...

-. 3. Carefully connect the RS232C DB-9 male end of the inierface cable from the device to the “SMDR” 
RS232C DB-9 female connector located at the bottom edge toward the left of the Option Module. 
The SMDR serial port output is one way to the printer or other Call Accounting device. Note: the KSU end 
is considered DCE and printer is DTE. 
L 
DCE MALE DB-9 DESIGNATION FEMALE. DTE 
DB-25 ’ 
1 DCD 8 
2 TD 3 
3 RD 2 
2 4 DSR 20 
iz 
bi 5 GND 7 
5 
6 DTR 6 $ 
7 CTS 4 
8 RTS 5 
9 RI 22 
The SMDR port baud...

X-RATE). This port must also be set to automatically acc&t.Jncoming Caller ID data; set the Data Link 
programming parameter to “AUTO” to complete this programming requirement. (RESOURCE - DATA 
LINK). 
The cable from the 1480-00 to the DHS Remote Programming port should be conf@red as follows: 
MALE 
m-9 CONNECTION z; 
6.13 External Paging Equipment (optional) 
Cd 
The system provides a one way paging output at the KSU fi-om the Option 
Module when instailed. An 1/8-&h phono jack labeled “53 EXT PAGE”...

6.13.1 Install the external paging equipment as’fobvs: 
1. 
3 
h. 
3. 
4. 
5. 
6. 
7. 
8. 
9. 
10. 
Cut a length of shielded cable to run fYom the 
amplifier to the KSU. 
Attach an eighth inch male phono plug to one 
end of the cable. 
Connect the other end of the cable to the 
amplifier high-impedance input according to the 
manufacturer’s instructions. 
Connect the paging speaker(s) to the amplifier 
using speaker cable. 
Plug in the amplifier’s AC power cord. DO 
NOT use the same AC outlet being used...

6.14 External Music Source - Standard MOHIBGM Module 
The Basic KSU is shipped with the Standard MOH/BGM Module. This module is 
located on a stand-off post toward the upper right corner of the CPU Module when c1-I -: 
viewing the installed KSU. The module provides a l/S-inch phono jack labeled 
“JKI MOH JACK” for direct connection to an external radio tuner, CD/tape player or other music source. 
The system music input impedance is 20K ohms. A trim POT (potentiometer) is also provided on the 
Standard...

OR: if the music source has an earphone jack attach another l/S-inch phono plug (or other specified 
connector) to the other end of the cable, and plug it into the earphone jack on the music source. 
3. Plug in the AC power cord for the music source. If possible. use a separate AC outlet than the one 
being used for the KSU. Turn on the AC power to the music source. 
.  4. Insert the l/S-inch phono plug into the appropriate music source jack inside of the KSU. 
5. Since the “MOH” music source serves to...

microphone voltage and allow the user to override the key.Jelephone MUTE operation. In this. case the 
headset adapter Mute finction must be used. (See headset manufacturer’s instructions for more details.) 
6.17 Battery Back-up 
In the event of commercial AC power outage, the system can maintain full operation if battery backup is 
used. When Battery back is required, the Starplus Battery Back up Unit is used. Follow the instructions 
supplied with the BBU to install batteries in that unit. Refer the...

6.18 Loud Bell Control (optional) 
When the Option Module is installed the system provides a dry contact closure to signal externallv nowered 
alerting devices for any incoming CO Line call. Transferred CO Lines that recall system wide‘ will also 
activate the LBC, in the same cadence as for an incoming CO Line ring. 
Installation 
1. Determine which CO lines should operate 
the Loud Bell Control (LBC) relay. 
Program & of these lines separately for 
LOUD BELL = Y. See CO LINE 
PROGRAMMING 
1 Battery I...

. . 
6.19 2 Port SLT Adapter 
The 2-Port SLT Adapter is used to connect analog single line telephones (SLT) and other analog devices to 
the system. The analog device must provide DTMF (touch tone) signals in order to make intercom calls, 
access outside lines and to activate system features. Some examples of analog devices are; telephone 
answering device (TAD), facsimile machine (FAX) or modem. 
Note: The 2-Port SLT Adapter is not an OPX device as determined by FCC Rules. 
The 2-Port SLT Adapter is...

6.20 2-Port SLT Expansion: 
The ‘-Port SLT Expansion is a single PCB identical to the PCB of the 2-Port SLT Adapter. One 2-Port 
SLT Expansion may be housed in the 2-Port SLT Adapter enclosure. The expansion is shipped with screws 
used to secure it to the existing 2-Port SLT Adapter PCB stand-offs. Since the PCB and circuit function are 
identical to the 2-Port SLT Adapter, follow the installation wiring instructions provided above for the 2- 
Port SLT Adapter. 
To install the 2-Port SLT Expansion into...