Vodavi Starplus 616 Flex Electronic Key System Installation Manual

%ARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
630.13 TOLL RESTRICTION TABLES (Cont’d) 
PROGRAMMING STEPS DESCRIPTION 
To delete an entry, the HOLD button must be 
pressed twice. 
If viewing allow/deny entries, the HOLD button must 
be pressed before leaving the program code. 
The Allow/Deny tables are reserved for COS 2 and 
3 respectively. A CO line marked Toll Restriction 
Override is not subject to restriction of COS 2, 3 or 
4. 
Default: 
Related Programming: 
Refer to Station Configuration, Sec. 610.1,...

START 
8 
0lGlT.S ARE 
DIALED ON 
A CO LINE 
DIGIT DIALED A 
I 
NO RESTRICTION 
APPLIED 
CALL IS ALLOWED 
I I THE CALL VlOLATES 
THE COS 4 RULES 
CALL IS RESTRICTED 
I NO RESTRICTION 
CALL IS ALLOWED  

630.14 STATION SPEED DIAL 
Each telephone has 20 unique speed dial numbers. 
These numbers are entered and stored by the user 
and can be recalled by the user at any time. 
The asterisk (‘) is used to program a pulse- 
to-tone switchover. Subsequent ‘*I dialed will 
cause the DTMF digit ‘*’ to be dialed. 
The TRANS/QUE button is used to program 
a pause 
The FLASH button is used to program a flash 
command. 
To program a “No Display”, press the CONF 
button. 
The asterisk (‘) and pound (#) can be pro-...

630.19 SYSTEM SPEED DIAL 
System speed dial numbers can be entered into the 
data base at the designated attendant station. 
A CO line can be programmed into a speed number. 
There can be 16 digits in the number including 
pause, pulse to tone switchover and flash com- 
mands. 
0 The asterisk (*) is used to program a pulse- 
to-tone switchover. Subsequent ‘*’ dialed will 
cause the DTMF digit ‘*’ to be dialed. 
l The TRANSKXJE to insert a pause com- 
mand 
l The Flash button to program a flash com-...

presented to the SLT. - 
C. Receiving an Audible Message Waiting 
Signal 
An SLA may receive an audible Message waiting 
signal in the form of the “system wide” Message wait 
Reminder tone. This tone must be enabled in the 
system data base program code 25. When mes- 
sage wait reminder tone is enabled ALL stations in 
the system will receive this alert tone at the pro- 
grammed interval including SLT’s connected to the 
SLA. Refer to the 630.2 for complete programming 
procedures to enable the Message...

STARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
630.23 DEFAULT DATA BASE CODES 
PROGRAMMING STEPS DESCRIPTION 
If you are in the program mode, continue using the 
program codes. If you are starting to program here, 
enter the program mode first. 
A. Default Station Data 
To initialize the Station Data, dial an (‘) asterisk and 
[00] on the dial pad. 
If you have a display phone, you will see the follow- 
ing: 
1. Press the HOLD button to initialize the Station 
Data. Confirmation tone will be heard. This data...

STARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
630.23 DEFAULT DATA BASE CODES (Cont’d) 
PROGRAMMING STEPS 
C. Default Svstem Data DESCRIPTION 
To initialize the System Data, dial an (*) asterisk and 
[20] on the dial pad. 
If you have a display phone, you will see the follow- 
ing: 
This data field is used to initialize all System Data. 
(Program Codes 21-39). 
Default: All applicable program codes returned to 
default (Program codes: 21, 22, 23, 24, 26, 27, 28, 
29,31,32,33,34,35,36,37,38, and 39) 
1. Press...

sTARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
630.23 DEFAULT DATA BASE CODES (Cont’d) 
PROGRAMMING STEPS DESCRIPTION 
E. Default Toll Table Data 
To initialize the Toll Table Data, dial an (*) asterisk 
and 1401 on the dial pad. 
If you have a display phone, you will see the follow- 
ing: This data field is used to initialize all Toll Table Data. 
(Program Codes 41-44). 
Default: All applicable program codes returned to 
default (Program codes: 41,42,43, and 44) 
Press the HOLD button to initialize the Toll...

sTARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
SECTION 640 
DATABASE PRINTOUT 
Station Configuration 
The Station Configuration printout will provide sta- 
tion related information in a !%character field in the 
following format: 
STA CONFIG 
CKT NUM COS DND SPD ALM PFL 
0110 1 Y Y N N 
CF DSLT PAGE BNA PKUP PAC HST 
Y Y 1,. . . 1,. Y N 
CKT NUM COS DND SPD ALM PFL 
02 11 1 Y Y N N 
CF DSLT PAGE BNA PKUP PAC HST 
Y Y 1,. . . 1,. Y N 
and so on through the rest of the stations 
CKT 
NUM 
cos 
DND 
SPD 
ALM 
PFL...