Vodavi Starplus 616 Flex Electronic Key System Installation Manual

sTARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
System Configuration 
The System Configuration related database infor- 
mation is provided in the following format: 
SYS CONFIG 
(ZUE HOLD ALM :DT :SIGL :ENBL 
Y SY CL REPT N 
PRV AMD SMDR BAUD PRNT BGM 
Y 10 ALL 1200 80 N 
LBC HOUR DATE 
. . 12 MMDD 
EX/SCl EX/SC2 EX/SC3 EX/SC4 
. . . . . . . . . . . . . . . . 
PBX CODES 
. . . . . . . . 
SMDR LINE ENABLE 
01 02 03 04 05 06 
QUE 
HOLD 
ALM 
DT 
SIGL 
ENBL 
PRV 
ATTD 
SMDR 
BAUD 
PRNT 
BGM 
LBC = Enabled = “Y”,...

System Timers 
The Timers printout will provide programmed infor- 
mation on all programmable timers in the system in 
the following format: 
TIMERS 
ERCL SRCL TRCL MSG-TNE PAUSE 
060 060 030 00 2 
RING-FWD CNFTO RNGTO 
30 
Where: 
ERCL 
SRCL 
TRCL 
MSG-TNE 
PAUSE 
RING-FWD 
CNFTO 
RNGTO 
15 50 
= Exclusive Recall Timer 
= System Recall Timer 
=Transfer Recall Timer 
= Message Wait Reminder Tone 
=Programmed length for a pause 
stored in a speed dial number 
=~usr~No Answer Ring Forward 
= Conference...

~ARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
System Speed Dial Printout 
System Speed Dial numbers programmed into the 
system can be displayed in this printout. Up to six- 
teen (16) digits can be displayed for each of the forty 
(40) bins. System Speed Dial numbers can be dis- 
played sequentially from bin 10 through 49, one bin 
and it’s data per line. 
SYSTEM SPEED 
10 ..30 . . 
11 ..31 . . 
12 . .31! . . 
13 ..33 . . 
14 ..34 . . 
15 ..35 . . 
16 ..3G . . 
17 ..37 .I 
18 ..38 . . 
19 ..39 . . 
20 ..40 ....

s-f-AFtPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
SECTION 700 
SYSTEM CHECKOUT PROCEDURES 
700.1 FUNCTIONAL TEST PROCEDURES 
This section describes the procedures that should 
be followed during system start-up. The installer will 
also find these tests to be helpful in the event of 
system mal-function and trouble shooting. System 
trouble shooting will be confined to replacement of 
key telephone sets & fuses. 
700.2 PRELIMINARY CHECKLIST 
Before starting the functional test procedures, it is 
recommended...

STARPLUs@ FLEX KEY TELEPHONE SYSTEM 
Table 700.1 
- Key Station Testing 
1 1. Connect the modular cord 
to the instrument. 
2. Press the ON/OFF button 
on the telephone. 
3. Background music 
3.1 With the telephone in an 
idle state, press “8” on 
the dial pad. 
3.2 Adjust voice volume 
(front) knob on telephone. 
3.3 Press “8” again. 
4. Do Not Disturb 
4.1 Press FWDIDND button. 
Telephone must be on- 
hook. 
4.2 Press DND button again. 
5. Tone ringing volume 
Telephone must be in ‘7 
mode. 
5.1 From...

Table 700.2 - Intercom Station Testing 
- 
1. 
1. 
Making an intercom call. 
Press DSS button or dial 
station number of desired 
party. 
if called phone is a 
speakerphone and is 
placed in H (voice) mode: 
1.2 if called station answers 
by lifting the handset.  OPERATIONAL TEST 
2. Call Pickup 
2.1 Press DSS button or dial 
station number of desired 
PaW. 
2.2 To answer at another 
station, lift handset or 
press ON/OFF button. 
2.3 Dial Pickup Code “6”. 
3. Intercom Conference 
31. During an intercom...

: 
STARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
Table 700.2 - Intercom Station Testing (Cont’d) 
OPERATIONAL TEST RESULT PROCEDURE 
5. Camp On (Call Waiting) 
5.1 Lift handset or press ON/ 
OFF button, then press 
DSS button or dial desired 
station number. Receive 
busy on outside (CO) or 
intercom call. 
5.2 Press MSG/CP.ON 
button. 
6. Executive/Secretary 
6.1 Transferring intercom 
calls to an Executive/ ’ 
Secretary phone. 
Incoming intercom call is 
routed to Secretary when 
Executive station is busy....

sTARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
Table 780.3 - CO Line Functions Test 
nPFRATlONA1 TEST RESULT PROCEDURE -. -* .~ . . .-. _. .- . -- . 
I. Outgoing calls 
I .I Lift handset or press ON/ 1 .I .l The CO line LED is lit 1 .I. 1 Normal 
OFF button & press CO steady. 
line button. 1 .I .2 Station OF/OFF button 1 .I .2 Normal 
LED is lit steady. All 
stations where DSS is 
programmed to appear 
are lit steady. Dial tone is 
heard. 
1 .I .3 CO LED is not lit. 1 .I .3 Check line access 
programming. 
2....

Table 700.3 - CO Line Functions Test (Cont’d) 
i 
OPERATIONAL TEST RESULT 
3.2 At phone receiving the 
transfer, press flashing CO 
line button or loop button. 3.2.1 CO line LED is now 
steady at all phones in 
the system. 
3.2.2 CO line call is not 
transferred to desired 
station. 
/ 4. Add-On Conference 
4.1 During a CO line conver- 
sation, press the CONF 
button. 
4.2 Press DSS button of 3rd 
party to be added to the 
conversation. 
4.3 When 3rd party answers, 
initiator presses CONF 
button again....

STARPLUS@ 616 FLEX KEY TELEPHONE SYSTEM 
SECTION 800 
MAINTENANCE AND TROUBLESHOOTING 
800.1 GENERAL INFORMATION 
This section provides common maintenance, trou- 
bleshooting and repair instructions for the STAR- 
PLUS 616 FLEX Key Telephone System. It is 
advisable to use the latest issue manual and sup- 
porting documentation whenever possible. 
The 616 FLEX architecture is designed such that all 
solid state circuitry is enclosed in the KSU. The only 
modular or replaceable type printed circuit boards...