Vivitek Qumi Q6 User Manual

							55
Advanced 2
To adjust the advanced settings, press  to enter the Advanced 2 sub menu.
ItemDescription
Test PatternPress the ◄ or ► button to select different test pattern.
H Image ShiftPress the ◄ or ► button to shift the horizontal position.
V Image ShiftPress the ◄ or ► button to shift the vertical position.  
						

							56
Settings 2 Menu
To access the Settings 2 menu and adjust the settings, perform the following steps:
1. Enter the OSD menu.
2. Press the ◄ or ► button to select the Settings 2 menu.
3. Press the ▲ or ▼ button to move the cursor up and down in the Settings 2 menu 
and press .
4. Press the ◄ or ► button to change values for each applicable setting.
ItemDescription
Auto SourcePress the ◄ or ► button to enable or disable automatic source 
detection.
No Signal Power Off 
(min)
Press the ◄ or ► button to automatically turn the projector lamp 
off when there is no signal.
Auto Power OnPress the ◄ or ► button to enable or disable automatic power on.
LED ModePress the ◄ or ► button to select the LED mode for higher 
brightness or lower brightness to save LED life.
Reset AllPress  to reset all items to factory preset values. See Reset All 
on page 57.
StatusPress  to enter the Status menu. See Status on page 58.
Advanced 1Press  to enter the Advanced 1 menu. See Advanced 1 on page 
59.
Advanced 2Press  to enter the Advanced 2 menu. See Advanced 2 on page 
60.  
						

							57
Reset All
To reset all of the menu items to the factory default values (except Language and Security 
Lock), perform the following steps:
1. Enter the OSD menu.
2. Press the ◄ or ► button to select the Settings 2 menu.
3. Press the ▲ or ▼ button to select the Reset All menu and press .  
						

							58
Status
To see the status of the Qumi, perform the following steps:
1. Enter the OSD menu.
2. Press the ◄ or ► button to select the Settings 2 menu.
3. Press the ▲ or ▼ button to select the Status menu and press .
ItemDescription
Active SourceDisplays the activated source.
Video InformationDisplays resolution/video information for RGB source and color 
standard for Video source.
LED Hours (Eco, 
Normal)
LED use information is displayed (in hours). Eco and Normal 
counters are separated.
Software VersionDisplay the software version  
						

							59
Advanced 1
To access the Advanced 1 menu and adjust the settings, perform the following steps:
1. Enter the OSD menu.
2. Press the ◄ or ► button to select the Settings 2 menu.
3. Press the ▲ or ▼ button to select the Advanced 1 menu and press .
4. Press the ▲ or ▼ button to move the cursor up or down in the Advanced 1 menu.
5. Press the ◄ or ► button to change values for each applicable setting.
ItemDescription
Menu PositionPress the ◄ or ► button to select different OSD location.
Translucent MenuPress the ◄ or ► button to select OSD background translucent 
level.
Low Power Mode
Press the ◄ or ► button to enable (
						

							60
Advanced 2
To access the Advanced 2 menu and adjust the settings, perform the following steps:
1. Enter the OSD menu.
2. Press the ◄ or ► button to select the Settings 2 menu.
3. Press the ▲ or ▼ button to select the Advanced 2 menu and press  or ►.
4. Press the ▲ or ▼ button to move the cursor up or down in the Advanced 2 menu.
5. Press the ◄ or ► button to change values for each applicable setting.
ItemDescription
Sleep TimerPress the ◄ or ► button to adjust the time for automatically lamp 
off (in minutes).
Source FilterPress  or ► to enter the Source Filter menu. See Source Filter 
on page 61.
White CalibrationPress  or ► to active the white calibration for re-build LED 
sensor data.  
						

							61
Source Filter
To adjust the source filter, press  or ► to enter the Source Filter sub menu.
ItemDescription
HDMI 1 / MHLPress the ◄ or ► button to enable or disable HDMI 1 / MHL 
source in auto search loop.
HDMI 2Press the ◄ or ► button to enable or disable HDMI 2 source in 
auto search loop.
USBPress the ◄ or ► button to enable or disable USB source in auto 
search loop.  
						

							62
Chapter 5  Taking Care of Your Qumi
Cleaning the Qumi
Cleaning the Qumi to remove dust and grime will help provide trouble-free operation.
Warning: 
1. The Qumi should be turned off and unplugged before cleaning. Failure to\
 do so may 
result in injury or damage to the system. 
2. Use only a dampened cloth when cleaning. Do not allow water to enter th\
e ventilation 
openings on the Qumi.  
3. If a small amount of water gets into the interior of the Qumi while cle\
aning, unplug the 
Qumi and set in a well ventilated area for several hours before using. 
4. If a large amount of water gets into the interior of the Qumi when clea\
ning, unplug the 
Qumi and have it serviced.
Cleaning the Lens
Optical lens cleaning solutions can be purchased from most camera and other retail 
stores. To clean the Qumi lens, perform the following steps:
1. Apply a small amount of the optic lens cleaning solution to a clean and soft cloth. (Do 
not apply the cleaning solution directly to the lens.)
2. Gently wipe the lens in a circular motion.
Caution: 
1. Do not use abrasive cleaners or solvents. 
2. To prevent discoloration or fading, do not allow the cleaning solution to\
 contact the Qumi 
case.  
						

							63
Troubleshooting
Common Problems and Solutions
These guidelines provide tips to deal with problems you may encounter while using the 
Qumi. If the problem remains unresolved, contact your dealer for assistance.
The problem sometimes can be as simple as a wire that is not completely connected.
Review the following possible issues before proceeding to the problem-specific solutions.
• Use another electrical device to confirm that the electrical outlet is properly working.
• Make sure that the Qumi is turned on.
• Make sure all connections are securely connected.
• Make sure that the connected device is turned on.
• Make sure that the connected PC is not in suspend or sleep mode.
• Make sure the connected notebook computer is properly configured for an external 
display.
Tips for Troubleshooting
In each problem-specific section, perform the steps in the order suggested. Doing so may 
help solve the problem more quickly.
In order to avoid replacing non-defective parts, try to find and isolate the problem.
For example, if you replace batteries and the problem remains, put the original batteries 
back and move to the next step.
Keep a record of the steps you take when troubleshooting. The information may be useful 
for reference when calling technical support or for bringing the Qumi to service personnel.
LED Error Messages
Error Code MessagesPOWER 
Blue Blink
TEMP 
Blue Blink
Over temperature error (Inlet air )-ON
LED over temperature (Red)-1
LED over temperature (Green)-2
LED over temperature (Blue)-3
Fan 1 (Blower) error61
Fan 2 (System) error62
Red LED Thermistor error81
Green LED Thermistor error82
Blue LED Thermistor error83
In the event of an LED error, disconnect the AC power cord and wait for one (1) minute 
before restarting the Qumi.
If there is any other situation that isn’t listed in the chart above, please contact your 
service center.  
						

							64
Image Problems
Problem: No image appears on the screen
1. Verify that the settings on your personal computer are properly configured.
2. Turn off all of the equipment and power up the equipment again in the correct o\
rder.
Problem: The image is blurred
1. Adjust the Focus on the Qumi.
2. Make sure the Qumi-to-screen distance is within the specified range.
3. Clean the Qumi lens with optical lens cleaning cloth if it is dirty.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the Qumi so that it is perpendicular to the screen as much as possible.
2. Adjust the Keystone settings in the OSD to correct the problem or set  Auto Keystone 
to On.
Problem: The image is reversed
Check the orientation of the Projection setting in the Installation I menu in the OSD.
Problem: The image is streaked
1. Set the Frequency and Tracking settings on the Computer menu in the OSD to the 
default settings.
2. Connect the Qumi to another computer to make sure that the problem is not caused 
by a computer’s video card.
Problem: The image is flat with no contrast
Adjust the Contrast setting in the Image menu in the OSD.
Problem: The color of the projected image does not match the source imag\
e
Adjust the Color Temperature and Gamma settings in the Image menu in the OSD.
Remote Control Problems
Problem: The Qumi does not respond to the remote control
1. Aim the remote control towards remote sensor on the Qumi.
2. Make sure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check to see if the battery polarity is correct.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.