Vivitek Qumi Q6 User Manual

							15
3.If more than one input device is 
connected, press the SOURCE 
button on the remote control 
and use the ▲ or ▼ buttons to 
select the applicable device or 
press ▲ and ▼ or ◄ and ► at 
the same time on the keypad on 
the Qumi.
• HDMI1/MHL: HDMI / DVI / 
MHL
• HDMI 2: HDMI / DVI
• USB: USB disc
4.Press the  POWER button to 
turn off the Qumi.
5.When the “Power Off? /Press 
Power again” message appears, 
press the  POWER button. 
The projector turns off.
Adjusting the Image
If the projected image is not clear, the image can 
be adjusted by moving the focus ring up or down 
until the image is clear.  
						

							16
Setting an Access Password (Security Lock)
To prevent unauthorized use of the Qumi, you can create a password. When the access 
password function is enabled, the password must be entered after the Qumi has been 
turned on. 
Creating a password can be done by performing the following steps:
1.Press the MENU button on the 
remote control or press MENU 
on the keypad to open the  
On-Screen Display (OSD) 
menu.
2.Move the cursor to the Settings 
1 tab and scroll down to select 
Advanced 1.
3.Press the ▲ or ▼ button to 
select Security Lock and press 
.
4.Press the ◄ or ► button to 
enable or disable the security 
lock function.
A password dialog box 
automatically appears.
5.You can use the ▲▼◄► 
buttons located either on top 
of the Qumi or on the remote 
control to enter the password. 
Any combination of the 
navigation buttons can be used 
(five must be chosen).
Press the navigation buttons in 
any order to set the password. 
Then press the MENU button to 
exit the dialog box.  
						

							17
6.The password confirmation 
menu appears when you 
power on the Qumi when the 
Security Lock is enabled. 
Enter the password that was 
created in step 5.
Important: 
Keep the password in a safe place. Without the password, you will not be able to use 
the Qumi. If you lose the password, contact your reseller for informatio\
n on resetting the 
password.
Using a Tripod
The Qumi can be used with a tripod by connecting 
the tripod to the bottom of the Qumi. Many typical 
tripods can be connected.
Supported Tripod Specifications:
• Type: Mini tripod
• Slot size: 1/4-20 L6.3 mm
Note: 
Remove sticker before use.  
						

							18
Setting Up the Remote
The remote control comes with one (1) 3V lithium 
battery (CR2025). The battery is pre-installed in 
the remote control.
To begin using the remote control, remove the 
plastic tab (A) from the battery compartment.
A
Replacing the Remote Control Batteries
1.Remove the battery 
compartment cover 
by sliding the cover 
towards the arrow 
(A). Then pull out 
the cover towards 
the arrow (B).
2.Remove the old 
battery and insert 
the new battery 
with the positive 
side facing up.
3.Install the cover.
AB
Caution: 
1. Use only a 3V lithium battery (CR2025). 
2. Dispose of used batteries according to local ordinance regulations.  
3. Remove the battery when not using the Qumi for prolonged periods.
Operating Range
The remote control uses infrared (IR) transmission to control the Qumi. It is not necessary 
to point the remote directly at the Qumi.
The remote control functions properly within a radius of approximately 7 meters (23 feet) 
and 15 degrees above or below the Qumi level (if the remote is not held perpendicular to 
the sides or rear of the Qumi).
If the Qumi is unresponsive to the remote control, move closer towards t\
he Qumi.  
						

							19
Chapter 3  Qumi User Interface
Overview
The Qumi User Interface (UI) is design to provide setting and operational ease of use. The 
UI also allows you to access media files from your smart devices (phones or tablets) or 
USB drives for a complete media experience.
The UI contains three main functions:
• Connect to PC - Allows the use of a connected PC as a storage device.
• EZ Media - Allows the use of media stored in the internal memory or a connected 
USB drive to display photos, music, audio and documents.
• EZCast Pro - Allows the streaming of media from smart devices or mirroring of 
connected Android/iOS/Mac/Windows  devices.
Note: 
After enabling the Connect to PC function, a reboot of the Qumi may be n\
ecessary to 
discover the PC.  
						

							20
Connect to PC
The Connect to PC function allows a connected PC to function as an exter\
nal storage 
device. Once connected, the Qumi can function as an external storage dev\
ice, which 
allows you to transfer media files directly to Qumi’s internal memory, and provide you with 
direct access to the projector function of the Qumi.
To use the Qumi projection function through the Connect to PC function, you will need to 
install the included software package, see the following information.
1. Power on your PC before starting the process.
2. Unpack the Qumi and set it on your desired location.
3. Connect one end of the power cord to the Qumi’s power socket and the other end to 
a wall socket.
4. Once both the PC and Qumi are powered on, connect one end of a type-A USB 
cable to the USB socket on the PC, and the other end to the USB socket on the 
Qumi.
5. Use the remote control to select Connect to PC and press  to initiate the USB 
connection to the PC.
6. If the PC detects the Qumi, the driver is automatically installed. A prompt displays 
notifying the device is ready for use.
Once the Qumi drivers are installed, two Auto Play folders display. The first folder 
contains the PC-based software, which provides the interface to access the Qumi 
projector functions directly from your PC.
The second folder is the Qumi internal memory for use as an external drive.  You can 
drag and drop files into the internal memory folder as you would any other storage 
drive.
Note: 
1.Built-in memory for Qumi Q6 is 4GB.(User Accessible is 2GB) 
2.The following screens are for reference only. The letters (F:) and (J:) are automatic 
designations by the PC. The designations may differ on your PC.  
						

							21
To provide PC access to the Qumi projection functions, you must first install the EZ USB 
software. 
7. Select the prompt labeled CD Drive (F:) USB DISPLAY (whereas F is the letter 
designation to the drive).
8. Click Open folder to view files. The EZ USB software is found in the folder.
9. Double click on the executable file to begin the installation process.
10. Once the EZ USB setup screen displays, select a installation language and click 
Next to proceed with the installation.
The Welcome to the Installation Wizard screen displays.  
						

							22
11. Click Next to continue the installation.
The License Agreement screen displays. Read the terms in the license agreement.
12. To continue, select Yes, I agree ... agreement then click Next. Otherwise click Back 
to return to the previous menu or Cancel to stop the installation.
13. In the Select installation folder field, enter the target folder to install the software 
(default: C:\Program Files\EZ USB).  
						

							23
14. Click Next to continue. Otherwise, click Back to return to the previous menu or 
Cancel to stop the installation.
15. Once the installation is finished, click Finish to conclude the process and exit the EZ 
USB setup.
The EZ USB software allows for display video or graphic from the PC.  
						

							24
EZ Media
The EZ Media center features Internal Memory, USB and Settings tools for the display of 
media files through the Qumi.
In the main menu, press the ◄ or ► on the remote to select EZ Media and press .
Supported Formats
The following file formats are supported:
• Image: JPEG, BMP
• Audio: MP1/MP2/MP3, WMA, OGG, ADPCM-WAV, PCM-WAV
• Voice record: MP3, WAV
• Video: AVI, MKV, TS, DAT, VOB, MPG, MPEG, MOV, MP4, WMV
• Adobe® PDF (.pdf) (PDF 1.0, 1.1, 1.2, 1.3 and 1.4)
• Microsoft® Word (doc/.docx)
• Microsoft® PowerPoint (.ppt/.pptx/.ppx/.ppsx) (not support Animation and slide 
transitions)
• Microsoft® Excel (97-2010, .xls/.xlsx)