Vivitek Projector DU8090Z User Manual

DU8090Z DLP Projector - User Manual 
 
10 
Control Panel 
 
POWER 
User the button to turn on/off the projector. 
 
INPUT 
Push the button to select the input signal. HDMI, DVI, 
VGA, Component…etc. 
 
AUTO SYNC 
Implement automatic signal synchronization. 
 
ASPECT 
Change the aspect ratio of the current image and push 
the button to change to the next aspect ratio settings. 
 
MENU 
Push the button to display or hide the OSD menu. 
 
UP/Down/Left/Right 
Use the button to select the OSD option. 
 
ENTER...

DU8090Z DLP Projector - User Manual 
 
11  
Remote Control 
 
 On 
Use the button to turn on the projector. 
OFF 
Use the button to turn off the projector. 
FOCUS 
Adjust the focus of the projected image. 
ZOOM 
Zoom in/out the projected image. 
TEST PATTERN 
Use the button to show the test pattern. Press this button again to switch to 
the next pattern. Press the EXIT button to return to the projected image. 
LENS SHIFT 
Use the button to move the lens right or left. 
ENTER 
Use the button to select...

DU8090Z DLP Projector - User Manual 
 
12  Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly 
at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the 
remote will function well within a radius of about 10 meters (25 feet) and 15 degrees above or below the projector 
level. If the projector does not respond to the remote control, move a...

DU8090Z DLP Projector - User Manual 
 
13 
Installing or Removing the Optional Lens 
 
 
Install New Lens 
1.  If the Lens cover is installed, pull the edge of the lens cover with one hand ( ①  ), so that the lens cover can be 
removed easily with the other hand ( ② )  
 
2.  Align the   symbol on the lens label with the *  symbol on the top of the body (align to the center of the lens 
hole) and pull in the lens. 
 
3.  Make sure the lens is pushed into the holder and turn it clockwise to the Lock...

DU8090Z DLP Projector - User Manual 
 
14   
Removing the Existing Lens 
1.  Push the LENS RELEASE button all the way in and rotate the lens counterclockwise. The existing lens will be 
disengaged 
 
2.  Pull out the existing lens slowly. 
 
 
 
Caution: 
When installing the lens into the projector, be sure to remove the lens cap from the back of the optional lens before 
installing the optional lens into the projector. Failure to do so will cause damage to the projector. 
There is one safety switch...

DU8090Z DLP Projector - User Manual 
 
15 
Lens Shift Range 
The DU8090Z projector has the lens shift feature; the image can be shifted vertically or horizontally without moving 
the projector. The lens shift range is shown in the percentage of the screen height, the maximum vertical shift range 
of the image can be up 50% and down 30%, maximum horizontal range is 10% to the right, 10% to the left. Please 
refer to below illustration. 
 
Vertical lens shift 
The projector is installed on the desk, the...

DU8090Z DLP Projector - User Manual 
 
16   
Horizontal lens shift 
The image can be shifted horizontally to the right or left by 10% (0.1H) without moving the projector. 
 
 
 
 
Note: 
 Above adjustable lens shift range is preset in DU8090Z for more flexible in installation, the best performance range 
of the lens may vary with projection lens. Please refer to the projection lens specification. 
 Lens shift range is reduced if Lens Type is set to UST Lens. Make sure Lens Type is set to Non-UST Lens...

DU8090Z DLP Projector - User Manual 
 
17 
Making Connections 
Follow the instructions below to connect DU8090Z projector to the video source, external control equipment (if any). 
When connecting to the equipment, use the correct signal cable to connect to the signal source and ensure that the 
cable is securely connected. Fasten the nut on the joint and connect the signal source equipment to the projector 
according to the figure below. 
 
Connecting to Personal Computer 
You can connect the PC signal...

DU8090Z DLP Projector - User Manual 
 
18 
Connecting to the Control Equipment 
The projector has the following control port for connecting to the control equipment: 
 
 
HDBaseT/LAN (Network control): The projector supports network control. LAN and Digital share the port. If only 
network control is used, you can connect the LAN on the projector to PC or through the local network. Refer to the 
remote control guidelines for 
RS-232 (RS-232 control): The projector can be remote-controlled by connecting...

DU8090Z DLP Projector - User Manual 
 
19 
Connecting to the Screen Trigger 
If your projection system includes the Electric projection screen and other 12V trigger device, you can connect these 
devices to the 12V trigger to output and configure the output 12V signal settings, such as automation and the aspect 
ratio of 16:10 through OSD control to Trigger. The projector will output 12V signals according to the current settings of 
the aspect ratio and trigger when turned on. You can use the signal to...