Vivitek Projector DU8090Z User Manual

							DU8090Z DLP Projector - User Manual 
 
10 
Control Panel 
 
POWER 
User the button to turn on/off the projector. 
 
INPUT 
Push the button to select the input signal. HDMI, DVI, 
VGA, Component…etc. 
 
AUTO SYNC 
Implement automatic signal synchronization. 
 
ASPECT 
Change the aspect ratio of the current image and push 
the button to change to the next aspect ratio settings. 
 
MENU 
Push the button to display or hide the OSD menu. 
 
UP/Down/Left/Right 
Use the button to select the OSD option. 
 
ENTER 
Use the button to select settings or confirm the changed 
settings. 
 
EXIT 
Push the button to return to the menu on the previous 
level or exit the OSD menu. 
 CENTER LENS 
Push the button to center the lens and calibrate the 
parameter of lens shift, focusing and zooming. 
Note: The lens memory function requires the accurate 
lens adjustment parameter. Please center the lens every 
time after the lens is mounted. 
 
Blank 
Use the button to stop the projection temporarily 
 
LENS SHIFT 
Use these four buttons to move the projected image to 
desired position. 
 
FOCUS 
Use the button to adjust the focus of projected image. 
 
ZOOM 
Use the button to zoom in/out the projected image. 
 
 
 
   
						

							DU8090Z DLP Projector - User Manual 
 
11  
Remote Control 
 
 On 
Use the button to turn on the projector. 
OFF 
Use the button to turn off the projector. 
FOCUS 
Adjust the focus of the projected image. 
ZOOM 
Zoom in/out the projected image. 
TEST PATTERN 
Use the button to show the test pattern. Press this button again to switch to 
the next pattern. Press the EXIT button to return to the projected image. 
LENS SHIFT 
Use the button to move the lens right or left. 
ENTER 
Use the button to select settings or confirm the changed settings. 
MENU 
Press the button to display or hide the OSD Menu. 
EXIT 
Press the button to return to the previous Menu or exit the OSD Menu. 
AUTO PC 
You can use this function to execute signal source auto synchronization 
BLANK 
Press the button to temporarily interrupt the projection. 
STATUS 
Show OSD MENU – SERVICE. 
VGA 
Select VGA input source. 
COMPONENT 
Select Component input source. 
ASPECT 
Press the button to display aspect ratio options. 
HDMI1 
Select HDMI1 input source. 
HDMI2 
Select HDMI2 input source. 
DVI 
Select DVI input source. 
3G-SDI 
Select 3G-SDI input source. 
DisplayPort 
Not available for this model. 
HDBaseT 
Select HDBaseT input source. 
CLEAR (Not Applicable) 
FREEZE 
Freeze / cancel the freeze of the projected image. 
ID SET (Not Applicable) 
Wired Remote Jack 
Connect to WIRED REMOTE terminal on the projector  
						

							DU8090Z DLP Projector - User Manual 
 
12  Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly 
at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the 
remote will function well within a radius of about 10 meters (25 feet) and 15 degrees above or below the projector 
level. If the projector does not respond to the remote control, move a little closer. 
 
 
Inserting the Remote Control Batteries 
 
 
 
1. Remove the battery compartment cover by sliding the cover in the direction of the arrow. 
2. Place two AA batteries with the correct polarity. 
3. Slide on the cover as the arrow in the illustration. 
 
Important:  
- Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can 
disrupt remote control operation. 
- Be sure nothing obstructs the path between the remote control and the projector.   
- Do not expose the remote control to high temperature or humidity; otherwise, the remote control will not work 
Battery installation instructions 
• Make sure the battery is installed with the correct polarity 
• Do not use the old and new batteries or the batteries of different types together 
• Remove the battery if the remote control may not be used for a long time to prevent the damage caused by leaks. 
123 
						

							DU8090Z DLP Projector - User Manual 
 
13 
Installing or Removing the Optional Lens 
 
 
Install New Lens 
1.  If the Lens cover is installed, pull the edge of the lens cover with one hand ( ①  ), so that the lens cover can be 
removed easily with the other hand ( ② )  
 
2.  Align the   symbol on the lens label with the *  symbol on the top of the body (align to the center of the lens 
hole) and pull in the lens. 
 
3.  Make sure the lens is pushed into the holder and turn it clockwise to the Lock position. When turning the lens, 
the Click sounds twice to indicate that the lens is completely fixed. 
 
4.  Check if the lens is fixed successfully by pulling the lens out of the holder gently. 
Caution: 
 Do not shake or place excessive pressure on the projector or the lens components as the projector and lens 
components contain precision parts. 
 When shipping the projector with the optional lens, remove the optional lens before shipping the projector. The lens 
and the lens shift mechanism may encounter damage caused by improper handling during transportation. 
 Before removing or installing the lens, be sure to turn off the projector and wait till the cooling fans stop, and turn off the 
main power switch. 
 Do not touch the lens surface when removing or installing the lens. 
 Keep fingerprints, dust or oil off the lens surface. Do not scratch the lens surface. 
 Work on a level surface with a soft cloth under it to avoid scratching. 
 If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.  
						

							DU8090Z DLP Projector - User Manual 
 
14   
Removing the Existing Lens 
1.  Push the LENS RELEASE button all the way in and rotate the lens counterclockwise. The existing lens will be 
disengaged 
 
2.  Pull out the existing lens slowly. 
 
 
 
Caution: 
When installing the lens into the projector, be sure to remove the lens cap from the back of the optional lens before 
installing the optional lens into the projector. Failure to do so will cause damage to the projector. 
There is one safety switch inside the lens slot on the projector to prevent unexpected injury by laser beam, the projector 
cannot be turned on if the projection lens has not been installed or is not installed correctly. Please make sure the lens is 
installed properly before tuning on the projector.  
						

							DU8090Z DLP Projector - User Manual 
 
15 
Lens Shift Range 
The DU8090Z projector has the lens shift feature; the image can be shifted vertically or horizontally without moving 
the projector. The lens shift range is shown in the percentage of the screen height, the maximum vertical shift range 
of the image can be up 50% and down 30%, maximum horizontal range is 10% to the right, 10% to the left. Please 
refer to below illustration. 
 
Vertical lens shift 
The projector is installed on the desk, the image can be moved up by 50% (0.5V) and down by 30% (0.3V). 
 
 
The projector is mounted on ceiling, the projected image can be moved down by 50% (0.5V) and up by 30% (0.3V). 
 
 
 
 
Caution: 
 Ceiling installation must be done by a qualified professional. Contact your dealer for more information. It is not 
recommended you install the projector yourself. 
 Only use the projector on a solid, level surface. Serious injury and damage can occur if the projector is dropped.  
						

							DU8090Z DLP Projector - User Manual 
 
16   
Horizontal lens shift 
The image can be shifted horizontally to the right or left by 10% (0.1H) without moving the projector. 
 
 
 
 
Note: 
 Above adjustable lens shift range is preset in DU8090Z for more flexible in installation, the best performance range 
of the lens may vary with projection lens. Please refer to the projection lens specification. 
 Lens shift range is reduced if Lens Type is set to UST Lens. Make sure Lens Type is set to Non-UST Lens if 
Non-UST lens is used.  
						

							DU8090Z DLP Projector - User Manual 
 
17 
Making Connections 
Follow the instructions below to connect DU8090Z projector to the video source, external control equipment (if any). 
When connecting to the equipment, use the correct signal cable to connect to the signal source and ensure that the 
cable is securely connected. Fasten the nut on the joint and connect the signal source equipment to the projector 
according to the figure below. 
 
Connecting to Personal Computer 
You can connect the PC signal to be projected to the projector through the DVI-D, HDMI, VGA or RGBHV (BNC) cable. 
If the signal to be input is VGA signal, connect the VGA cable to the external display to simultaneously monitor the 
projected content. 
 
Connecting to the Video Device 
Connect the video equipment to the input port of the projector via the DVI-D, HDMI, Component Video, Composite 
Video or S-Video Connector. 
 
  
						

							DU8090Z DLP Projector - User Manual 
 
18 
Connecting to the Control Equipment 
The projector has the following control port for connecting to the control equipment: 
 
 
HDBaseT/LAN (Network control): The projector supports network control. LAN and Digital share the port. If only 
network control is used, you can connect the LAN on the projector to PC or through the local network. Refer to the 
remote control guidelines for 
RS-232 (RS-232 control): The projector can be remote-controlled by connecting the projector to PC or control system   
Through the standard 9-pin serial cable (Straight Through Serial Cable). Refer to the Remote Communication Manual 
for detailed information. 
Wired remote control: If the projector cannot receive the IR signal from the remote control due to the overly long 
distance or obstacles, you can connect the cable to the IR remote control or the external IR transmitter (optional) via 
the WIRE input port to expand the working range of the remote control. 
3D Sync Out/In: Connect to 3D IR sync signal transmitter or device. 
 
 
 
 
Caution: 
 When the terminal of the remote control cable is inserted to the wired control terminal of the projector, the 
projector will automatically switch to the wired control mode and cannot be controlled through the IR signal of 
the remote control. Disconnect the wired control terminal on the projector if you want to control through the IR 
signal of the remote control. 
 If the wired remote control cable or the external IR transmitter is inserted to the incorrect port, such as Trigger, 
the remote control or the IR transmitter may be damaged. Make sure whether the port is correct  
						

							DU8090Z DLP Projector - User Manual 
 
19 
Connecting to the Screen Trigger 
If your projection system includes the Electric projection screen and other 12V trigger device, you can connect these 
devices to the 12V trigger to output and configure the output 12V signal settings, such as automation and the aspect 
ratio of 16:10 through OSD control to Trigger. The projector will output 12V signals according to the current settings of 
the aspect ratio and trigger when turned on. You can use the signal to control the screen or device.