Vivitek Projector DU8090Z User Manual

							DU8090Z
Users Manual
Users Manual 
						

							DU8090Z DLP Projector - User Manual 
 
1
 
Table of Contents 
 
Copyright ............................................................................................................................................................ 2 
Copyright ...................................................................................................................................................... 2 
Disclaimer .................................................................................................................................................... 2 
About the Manual ......................................................................................................................................... 2 
Important Safety Guidelines ............................................................................................................................... 3 
Safety Notification ........................................................................................................................................ 3 
Installation and Use Notices ......................................................................................................................... 5 
Disposal of Old Electric and Electronic Equipment ...................................................................................... 5 
Important Recycling Instructions .................................................................................................................. 5 
Introduction ......................................................................................................................................................... 6 
Packing Checklist ......................................................................................................................................... 6 
Projector Overview ....................................................................................................................................... 7 
IO Panel ....................................................................................................................................................... 9 
Control Panel ............................................................................................................................................. 10 
Remote Control .......................................................................................................................................... 11 
Installing or Removing the Optional Lens .................................................................................................. 12 
Lens Shift Range ........................................................................................................................................ 15 
Making Connections ......................................................................................................................................... 17 
Connecting to Personal Computer ............................................................................................................. 17 
Connecting to the Video Device ................................................................................................................. 17 
Connecting to the Control Equipment ........................................................................................................ 18 
Connecting to the Screen Trigger .............................................................................................................. 19 
Connecting to external HDBaseT Transmitter ............................................................................................ 20 
Using the projector ............................................................................................................................................ 21 
Select the Input Voltage of AC Power ........................................................................................................ 21 
Connecting to AC Power Supply ................................................................................................................ 21 
Turning on the Projector ............................................................................................................................. 21 
Turning off the Projector ............................................................................................................................. 22 
Using On-Screen Display ................................................................................................................................. 23 
Using the OSD Menu ................................................................................................................................. 23 
Menu Tree .................................................................................................................................................. 24 
OSD Operation – INPUT ............................................................................................................................ 27 
OSD MENU – PICTURE ............................................................................................................................ 30 
OSG MENU – ALIGNMENT ..........................................................................................................
............. 31 
OSD MENU – CONTROL .......................................................................................................................... 34 
OSD MENU – SERVICE ............................................................................................................................ 37 
Product Specification ........................................................................................................................................ 38 
Supported Signal Input Timing .......................................................................................................................... 39 
Product Dimensions.......................................................................................................................................... 41 
LED Indication .................................................................................................................................................. 42 
About the VIVITEK Support .............................................................................................................................. 43 
 
  
						

							DU8090Z DLP Projector - User Manual 
 
2 
Copyright 
Copyright 
The Users Manual (including all pictures, illustrations and software) is protected by the international copyright right 
law. All rights are reserved. No duplication of the manual or any content included in the manual is allowed without the 
written consent of the manufacturer.   
Vivitek is the trademark of Vivitek Corporation. ©All rights reserved. 2016 
 
Disclaimer 
The information in the manual is subject to change without notice. The manufacturer does not provide any statement 
or warranty of the contents in the manual and clearly give up the implied warranties of merchantability and of fitness 
for a particular purpose. The manufacturer reserves the rights to modify the publication and change the contents of 
the materials at any time without notice to any person.   
 
About the Manual 
The manual describes how to install and use the DLP projector and is applicable to the end-user. Relevant 
information (such as illustrations and descriptions) is put on the same page as possible as we can. The format, easy 
for printing, is convenient for reading and paper-saving which is beneficial to environmental protection. It is 
suggested printing the page you need.  
						

							DU8090Z DLP Projector - User Manual 
 
3 
Important Safety Guidelines 
Thank you for purchasing the high quality product! 
Read the Manual carefully to obtain the best performance. The Manual provides instructions to use the menu and 
implement operation. 
 
Safety Notification 
 To turn off main power, ensure to unplug from power outlet. 
 To prevent electric shock, do not open the cabinet. There are high-voltage components inside. 
Refer service to qualified service personnel. 
 The symbol warns the user about electric shock caused by voltage not insulated. Therefore, it is dangerous 
to make any kind of contact with any parts of inside units. 
 This symbol alerts the user that important information which should be read carefully to avoid problems 
concerning the operation and maintenance. 
 
WA R N I N G !  
To prevent the projector from electrical discharge or electric shock, do not expose the projector to rain or 
moist environment. Do not use the plug with an extension cord or an outlet unless all the prongs can be 
fully inserted. 
 
WARNING TO CALIFORNIA RESIDENTS: 
Handling the cables supplied with this equipment might expose user to a little lead, a chemical known to the Stage of 
California, resulting in risks of barrenness. Please remember to wash hands after handling. 
NOTIFICATION (CANADA) 
This class A digital equipment complies with Canadian ICES-003. 
CE NOTIFICATION 
This is a class A product, which complies with rules for CE marking. This product may cause radio interference that 
the user may be supposed to take adequate measures. 
FCC NOTIFICATION 
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference; (2) this device must accept any interference received, including 
interference that may cause undesired operation. This equipment has been tested and found to comply with part 15 
of the FCC Rules. These requirements are designed to provide reasonable protection against harmful interference 
when the equipment operates in a commercial environment. This equipment might generate radio frequency energy. 
If user does not install or use in accordance with the instructions in manual, the radio frequency energy may interfere 
radio reception. If the above scenario occurs, the user may be responsible to correcting the interference 
 
 WARNING!  
Changes or modifications without approval from Vivitek could void the user’s authorization to 
operate the product. 
LIGHT MODULE 
  A light module containing multiple laser diodes acts as the light source in the product.  
						

							DU8090Z DLP Projector - User Manual 
 
4    These laser diodes are sealed in the light module. It is recommended to ask dealer for maintenance or repair 
services of the light module. 
  End user is not allowed to replace the light module. 
  Contact distributor who provides the qualified service for light module replacement and further information. 
LASER SAFETY NOTIFICATION AND CAUTION 
 Do not stare at the lens while in use 
  CLASS 3R LASER PRODUCT   
  This Laser Product is designated as Class 3R during all procedures of operation.   
  LASER LIGHT - AVOID DIRECT EYE EXPOSURE.   
  Do not point laser or allow reflected laser light toward other people or reflective objects.   
  Direct or scattered light can be hazardous to eyes and skin.   
  There is a potential hazard of eye exposure to laser radiation if the included instructions are not followed.   
  Caution – use of controls, adjustments or performance of procedures other than those specified herein may result 
in hazardous radiation exposure. 
Laser Parameters: 
Wavelength  : Maximum laser energy 
450nm - 460nm (Blue)  : 0.376mJ 
Mode of operation  : Total internal power 
Pulsed, due to frame rate  : >100W 
Pulse width  : Apparent source size 
0.74ms  : >10mm, at lens stop 
Pulse repetition rate  : Divergence 
24Hz  : >100 mili Radian 
Product Label 
Manufacturer’s ID Label, Explanatory Label and Certification Statement Label 
Hazard Warning Symbol and Aperture Label 
 
 
 
 
  
						

							DU8090Z DLP Projector - User Manual 
 
5 
Installation and Use Notices 
1.  Read and keep this manual properly. 
2.  Pay attention to all the noted warnings, and follow all the guidelines and descriptions in this manual. 
3.  Do not use the projector near water. 
4.  Do not install the equipment near the thermal sources, such as heaters, radiators, furnace, amplifiers, and any 
other equipment that may generate heat. 
5.  Be careful while holding the equipment or moving the trolley with projector to prevent the equipment from 
turning over. 
6.  Notice whether there is any parts with flaws after receiving the projector. 
7.  Please notice that the projector will not power on until the lens is fitted. The protection covering the lens should 
be taken to install the lens.   
8.  Do not let any vent be obstructed.   
9.  Do not destroy the safety protection function of polarized or grounding plug of power cord. A polarized plug has 
one wide and one narrow blade. The plug has two blades and one grounding blade. The wide blade or 
grounding blade is provided for the safety concerns. If the plug provided does not match the outlet, please 
contact the electrician to change outlet.   
10.  The +12V trigger only outputs 12V DC trigger signal. Do not connect other power input or output. Otherwise, 
the equipment may malfunction. 
11.  Adjust the slide switch with suitable volt input, and then plug in the projector; the red LED indicator would flash 
and then stabilize, getting into standby mode. User should only use the connectors or accessories provided by 
the manufacturer. 
12.  When user turns on the projector, the red LED indicator would flash until stabilize. Do not look at the lens 
directly while the projector is running. 
13.  Unplug the power cord of the equipment if there is a thunderstorm or the equipment is not going to be used for 
a long time. 
14.  The packaging materials can be kept properly for transportation use afterwards. 
15.  If any breakdown occurs, please contact dealer or manufacture for qualified repair service. 
 
Disposal of Old Electric and Electronic Equipment 
The symbol on your product or the package represents that the product should not be treated as the normal 
household waste when discarded but should be carried to the recycling location of the waste electric and electronic 
equipment. The consequence on the environment and human health due to the incorrect disposal of the product can 
be prevented if it can be ensured that the product is properly discarded. Material recycling is helpful to the protection 
of natural resources. The symbol is only valid in European Union. If you want to discard electrical and electronic 
equipment, contact the governmental authorities or your dealer for the correct method of disposal. 
 
Important Recycling Instructions 
The lamp of the product contains mercury. The product may contain other electronic wastes and may pose risk if not 
discarded properly. Abide by the local, state/provincial or federal laws of recycling or discarding. For more 
information, please visit the website and contact Electronic Industries Alliance (EIA) on WWW.EIAE.ORG. 
Please visit WWW.LAMPRECYCLE.ORG for the specific disposal information of lamps.  
						

							DU8090Z DLP Projector - User Manual 
 
6 
Introduction 
 
The Users Manual describes the installation, setup and operation of the DU8090Z projector and provides assistance 
to the installation personnel and the end-user to fully develop the performance of the projector. VIVITEK has made 
every effort to ensure that the information in the Manual is correct at the time of printing. The contents may be 
frequently updated due to the continuously product improvement and customer feedback. 
You can find the latest version of the Manual and the manual of other Vivitek products on www.vivitekcorp.com. 
 
Packing Checklist 
The following items are included in the packaging box of the DU8090Z series projector. If any loss or damage to any 
item, contact your dealer or the VIVITEK customer service department. 
 
 
    
AC Power Cord      Power Cord        VGA Signal Cable 
           
 
  
IR Remote Control        Cable of the Wired      Anti‐thief Screw for 
          Remote Control      Lens Installation 
(M4) 
 
 
  
User ’s Manual Disc        RoHS Card (China)      Qualification 
                 Certificate (China)
  
						

							DU8090Z DLP Projector - User Manual 
 
7 
Projector Overview 
 
Front-right View 
 
 
 
 
 
 1. Front IR Receiver 
The Receiver for IR signals from remote control. 
2. LED Indicator 
Display current projector status such as power, light source status 
and warning. 
3. Air Intake 
      The fan pulls the cool air to the projector for system cooling. 
4.  Lens Release Button 
        Press the Lens Change button before removing the lens. 
5. Lens hood 
Remove the cover before installing the lens. 
6. Height Adjuster 
Adjust level of projector 
7. Intake Vent  
The fans pull air to cool the radiator of the projector. 
8. Rear IR Receiver 
        The Receiver for IR signals from remote control. 
 
Rear-right View 
 
 
 
 9.  I/O Connector Panel 
Connect to various input, control or output terminals to the 
projector. 
10. Kensington Lock 
        Attach the projector to a permanent object with the Kensington 
slot and a security cable. 
11. Slide Switch 
 
12.  AC Power Switch 
        Turn on/off the AC power of the projector. 
13. AC Inlet 
      Connect the supplied power cable to this inlet. 
14. Control Panel   
        Press the button to operate the OSD menu or adjust the lens   
Settings see OSD controls. 
 
 
 
1 2 
3 4 
5 
6 
7
8 
9 
10 11  
12 
14
13 
Important: 
Grill openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct 
any of the grill openings 
  
						

							DU8090Z DLP Projector - User Manual 
 
8  Bottom View 
 
 
 
 
 15.  Anti-thief Screw hole 
The anti-thief screw can be fastened to prevent 
Lens removing by unauthorized person. 
16.  Mounting Holes of Support Kit 
These two screws holes can be used to fix 
support kits of ultra-short throw lens. 
Note: The screws are for Lens support kits only; 
overloading may damage the projector or cause 
injury. 
17.  Recess for projector handling. 
These four recesses can be used for handling 
the projector. 
18.  Ceiling Mounting Hole 
Total, 6 holes for M4 screw, maximum depth 
14mm. 
19. Security Slot 
The slot can be used for Short-term protection 
 
 
 
 
 
 
 
17 
15 
16 
18 
19 
Note: 
 When installing, ensure that you use only UL Listed ceiling mounts, Contact your dealer for information on 
mounting the projector on a ceiling. 
 With ceiling installation, use approved mounting hardware & M4 screws; maximum depth of screw: 18 mm.  
						

							DU8090Z DLP Projector - User Manual 
 
9 
IO Panel 
 
TRIGGER(12V +/-1.5V) 
When connected to the screen thtough a 3.5mm cable, 
the screen deploys automatically on start up of the 
projector. The screen reacts when the projector is 
powered off.   
 
RS-232 
The 9-pin D-sub interface is used to connect to the PC 
control system and projector maintenance. 
 
Component (V, H, B/Pb, G/Y, R/Pr) 
Connect RGBHV or Component signal from computer or 
component video enabled device 
 
VGA 
Provide the standard 15-pin VGA connection and can 
connect to RGB, HD Component or personal computer. 
 
MONITOR OUT 
Connect to a monitor to display the projected content. 
 
WIRED REMOTE 
Connect the supplied remote controller to the projector 
 HDBaseT/LAN 
Connect an Ethernet cable (Cat5/Cat6, not supplied) from 
a computer, network device, or HDBaseT transmitter.   
 
HDMI I   
Connect the HDMI cable from a computer or video device 
 
DVI-D 
Connect to DVI-D cable from a DVI-D output of the 
device.  
 
SDI IN/OUT 
Connect to SDI source. 
 
HDMI II   
Connect the HDMI cable from a computer or video device
 
3D SYNC IN / Out 
Connect to the 3D IR synchronization signal transmitter. 
 
 
 
 
 
 
Note for Wired Remote 
 Please make sure whether the port for insertion is correct before the terminal of the wired remote control is 
inserted. The remote control may be damaged if inserted to the wrong port such as trigger. Do not use this jack for 
anything other than intended use. 
Note for Trigger 
 When the projector is turned on, a control signal (DC 12V) outputs from this terminal, Screen controllers are 
supplied and supported by screen manufacturers. 
 Do not use this jack for anything other than intended use.