Vivitek Projector DU8090Z User Manual

							DU8090Z DLP Projector - User Manual 
 
30 
 
OSD MENU – PICTURE 
Picture Mode 
Use ◄or► to select desired picture mode 
High Bright: The highest brightness output mode is suitable for the application where the highest brightness output 
is needed. 
Presentation: The best projection effect is suitable for the presentation or picture. 
Video: The mode is suitable for playing video content. 
 
Brightness 
Press ENTER, and use ◄ or ► to increase or decrease the level of brightness. 
Contrast 
Press ENTER, and use ◄ or ► to adjust the contrast of the projected image. 
Saturation 
Press ENTER, and use ◄ or ► to adjust the level of saturation. 
Hue 
Press ENTER, and use ◄ or ► to adjust the level of hue.   
Sharpness 
Press ENTER, and use ◄ or ► to adjust the sharpness, which changes the high-frequency details. 
 
Color Temperature 
The default of color temperature is Native, and it is suitable for most situations. As color temperature rises, the picture 
will appear bluer, while as the color temperature decreases, the picture will appear redder. The available options are 
Native, 5400K, 6500K, 7500K and 9300K 
 
Gamma 
When the ambient light is so bright that may affect the projection of the details in the dim area of the image, you can 
change the gamma to adjust the chrominance. The available options are 1.0, 1.8, 2.0, 2.2, 2.35, 2.5 and S-Curve. 
 
Input Balance 
When ambient light is too bright or changes, the projected image details may be affected, you can adjust the option to 
make the projected colors of image closer to desired colors. There are two options for fine tuning Red, Green and Blue. 
						

							DU8090Z DLP Projector - User Manual 
 
31  Offset: These three options will shift the color spectrum for the whole image and change its brightness, if minimal amount 
of red, green or blue appears in the gray areas, you can adjust the offset of the corresponding color accordingly. By 
increasing the offset, the image brightness will become lower. 
Gain: These three options are used to increase or decrease the range of color input for the entire image. If minimal 
amount of red, green or blue appears in the gray areas, lower the gain of the corresponding color accordingly. As gain 
increases, the contrast of the image will become lower. 
 
 
HSG 
HSG is a function to adjust Hue, Saturation and Gain independently, it allows for specified color adjustments that are more 
intuitive. You can adjust Hue, Saturation and Gain for Red, Green, Blue, Cyan, Magenta, Yellow and white independently. 
 
Noise Reduction 
Use ◄► to adjust the noise of the projected image. This function is used to remove the noise of the image with interlaced 
scanning input. Generally, noise reduction can lower the high-frequency details and make the image softer. 
 
Dynamic Black 
This is function can be used to enhance the black level of the projected image.   
 
OSG MENU – ALIGNMENT 
 
 
Lens Lock 
This function can be used to disable lens control for preventing unauthorized operation or disoperation in lens control 
related functions including Lens Shift, Zoom/Focus Adjustment and Center Lens. Recommend to turn on Lens Lock 
function to disable the Lens control after lens adjustment is done. 
 
Lens Control
  
Select this function to open Lens Control menu for adjustment of Zoom, Focus, or Shift. You can use the ENTER button to 
switch the Zoom / Focus or Shift menu. Use ▲or▼ to adjust zoom and vertical shift of the lens, or use ◄ ► to adjust 
focus and horizontal shift of the lens. 
 
 
 
 
  
						

							DU8090Z DLP Projector - User Manual 
 
32  Lens Type 
There are eight projections lens can be used in DU8090Z, the initial projection position of Ultra Short Throw (UST) Lens is 
different to other seven projection lenses. The projector preset two initial projection positions for these two types 
accordingly, Center Lens function can moves the lens to the initial position (center) automatically per the setting. Please 
set this option to UST Lens if Ultra Short Throw Lens is installed in the projector, otherwise please set it to 
 
 
Lens Memory 
This projector supports Lens Memory function, Lens shift, Zoom and Focus memory can be stored in the projector up to 
10 sets. You can load the stored memory setting to set up the lens automatically. 
Load Memory: Use ▲▼ to select the desired memory setting then press ENTER button to execute the lens setting, 
the projector will adjust the Lens position, Zoom and Focus automatically. 
Save Memory: Use ▲▼  to select the memory set for storing the setting then press ENTER button to confirm. 
Clear Memory: Select the memory set to be cleared then press ENTER button to confirm clearing memory set. 
Center Lens 
This is the lens calibration function, the projector calibrates the lens shift, focus and zoom parameters for the precise lens 
memory function. After performing this function, the lens will be moved to the center position as factory default setting. 
 
Digital Zoom   
Press ENTER button to select the options to enlarge the image or shift the image.   
Digital Zoom: Use ◄► to enlarge the projected image. 
Digital Pan:  Use ◄► to move the projected image horizontally. This function is only available when projected image 
is enlarged. 
Digital Scan: Use ◄► to move the projected image vertically. This function is only available when projected image is 
enlarged. 
Reset: The setting will be reset to default value. 
 
Warp 
This function is used to correct the distortion of image. 
Keystone: Press ◄► to correct horizontal distortion or ▲▼ to correct vertical distortion. 
Rotation: Press ◄► to correct incorrect angle of image. 
Pincushion / Barrel: Press ◄► to correct pincushion/barrel distortion. 
Top Left Corner: Press ◄► to correct the distortion at top-left of the picture. 
Top Right Corner: Press ◄► to correct the distortion at top-right of the picture. 
Bottom Left Corner: Press ◄► to correct the distortion at bottom-left of the picture. 
Bottom Right Corner: Press ◄► to correct the distortion at bottom-right of the picture. 
Note: 
 The lens will moved to the position which is lower than the initial projection of Ultra Short Throw Lens after 
performing Center Lens function, and cause the projected image is blocked by the top cover of the projector if 
it’s set to Non-UST Lens. In this case, please perform the Lens shift function to move up the Lens till the 
image can be projected normally.   
 If Ultra Short Throw Lens is installed and UST Lens is selected, you can perform Center Lens to move Lens to 
initial projection position automatically. 
 When using non-UST lens and lens shift range is limited, please make sure Lens type setting is set to 
Non-UST Lens. 
Note: 
 There are two default center positions for UST (Ultra Short Throw) Lens and non-UST Lens, make sure Lens 
Type setting is correct before performing this function.     
 If Ultra Short Throw Lens is installed, make sure the support kit is detached before performing Center Lens.  
						

							DU8090Z DLP Projector - User Manual 
 
33  Blanking: This function can adjust the edges of the image and hide surplus sections of the projection. 
Top: Press▲▼ to adjust the top blanking area on the projected picture. 
Bottom:Press▲▼ to adjust the bottom blanking area on the projected picture. 
Left: Press ◄► to adjust the left blanking area on the projected picture. 
Right: Press ◄► to adjust the right blanking area on the projected picture. 
Reset 
All the settings toward blanking will set to default. 
 
Edge Blend 
Edge Blend function requires multiple projectors to simultaneously project on the same screen. Use this function to adjust 
the uniformity of image. To use this function, Edge Blending must be enabled on both projectors. The functions as follows 
can be only adjusted when Edge Blend is turned on.   
Edge Blend: If the user would like to function Edge Blend, turn this function to On. 
Align Pattern: If user turns this function to On, the projector will show pattern for user to adjust the overlapping part of 
projection. 
White Level: White Level is used to set the overlapped area for blending in multi-projection application, the 
overlapping When projecting White, the area where the two images overlap is projected twice the projectors white 
output levels. The solution is to adjust the White Level. First make sure that the units connected to the projectors are 
outputting black. Then increase the White Level (Top, Bottom, Left, and Right) until the non-overlap areas brightness 
matches the overlap area. 
Black Level: The purpose of Black Level is to increase the black level of non-overlapping area. When projecting black, 
the area where the two images overlap projects twice the projectors black output levels. The solution is to adjust the 
Black Level. First make sure that the units connected to the projectors are outputting black. Then increase the Black 
Level (Top, Bottom, Left, and Right) until the non-overlap areas brightness matches the overlap area.   
Reset: All the settings toward edge blend will set to default.   
 
Screen Format: Sleet the screen format to 16:10, 16:9 and 4:3.   
 
  
						

							DU8090Z DLP Projector - User Manual 
 
34 
 
OSD MENU – CONTROL 
 
Language 
Select desisted OSD language, the available languages options are English, Española, Deutsch, Portuguese, 简体中文, 
繁體中文, 日本語, 한국어. 
 
Projection Mode 
Use The projection mode option can be used to change the direction of the projected image. 
Front: Install the projector on the table and project the image on the screen forward. 
Ceiling + Front: Mount the projector on the ceiling and project the image on the screen forward, the image is 
overturned. 
Rear: Install the projector on the table and project the image from the rear of the screen. 
Ceiling + Rear: Mount the projector on the ceiling and project the image from the rear of the screen, the image is 
overturned. 
Auto: Built-in sensor detects the projector orientation and switch corresponding projection mode, note this function is 
applicable for front projection only, the image orientation when projecting from rear has to be adjusted manually. 
 
Cooling Condition 
The projector is equipped with orientation sensor for switching cooling condition automatically; you can set it to Auto or 
adjust the cooling condition by manual. 
Front: The projector is installed on the table. 
Ceiling + Front: The Projector is mounted on the ceiling. 
Freetilt: The projector is installed with tile angle; the angle is over 30 degree.   
Auto: Built-in sensor detects the installation orientation and switches to corresponding cooling condition. 
 
High Altitude 
Use this function to adjust the cooling fan of the projector to get well cooling if the projector is installed in an area over 
5000 feet. The projector is equipped with altitude sensor which is capable of detecting atmosphere pressure for estimating 
altitude; it can adjust automatically to corresponding setting based on estimated altitude if this option is set to Auto. If you 
Note: 
 Incorrect Projection Mode setting may affect hot air exhausting from the projector, the heat and high 
temperature may cause the projector to enter system protection or damage component.    
						

							DU8090Z DLP Projector - User Manual 
 
35  prefer to set it by manual, you can select On or Off. 
Off: Turn off High Altitude mode if the projector is installed in an area under 5000 feet. 
On: Turn on High Altitude mode if the projector is installed in an area over 5000 feet. 
Auto: Set up this mode automatically by estimated altitude. 
 
Auto Power Off 
This function is set to OFF by default. When it is set to ON and no input signal is received within 20 minutes, the projector 
will turn off automatically. 
 
Auto Power On 
This function is set to OFF by default. When it is set to ON, the projector will turn on automatically when y AC power is 
turned on next time. You can use this function and the power switch (instead of the remote control) to turn on the projector. 
Set this function to OFF if it’s unnecessary.   
 
Network 
Use this function to configurator the network settings so that you can control the projector via the network.   
Press ▲▼ and Enter button to select Network and network settings. Please refer to Remote Communication Manual for 
further information. 
Standby Power 
This option allows you to set up power consumption at standby status, 
On: Projector maintains in the standby at higher power consumption (< 6W) for projector control via LAN. In this 
mode, the projector can be turned on by RS-232 command or web control. 
Off: Projector maintains in the standby at lowest power consumption (
						

							DU8090Z DLP Projector - User Manual 
 
36   
Background 
User can use this function to specify the image displayed on the blank screen when there is no input signal. The 
selectable items are Logo, Black and Blue, the default setting is Logo.
 
 
Startup Logo 
Press ENTER button, and use the ◄► function to turn on / off the Startup Logo.  
 
Remote Sensor 
The default is On. However, there are three conditions that will be suggested to turn off “Remote Sensor”; the possible 
condition is that if the user uses wired control, he or she can set this function to Off, or that if the projector IR location is 
exposed to the bright sunlight or fluorescence, or that projector control is not controlled by remote. If the user would like to 
reset to On, user can only set by OSD panel or RS-232.   
 
Trigger 
The projector is provided with a set of trigger output. User can connect the trigger to the screen with projector by the cable. 
If user does so, once the projector is powered, the screen would be automatically turned on as well. There is a 2-3 second 
delay to activate this function. The selectable aspect ratios are as follows: 
Off: Turn off screen trigger. 
5:4: Outputs 12V of power on Trigger when Aspect Ratio is set to 5:4. 
4:3: Outputs 12V of power on Trigger when Aspect Ratio is set to 4:3. 
16:10: Outputs 12V of power on Trigger when Aspect Ratio is set to 16:10. 
16:9: Outputs 12V of power on Trigger when Aspect Ratio is set to 16:9. 
1.88: Outputs 12V of power on Trigger when Aspect Ratio is set to 1.88. 
2.35: Outputs 12V of power on Trigger when Aspect Ratio is set to 2.35. 
Letterbox: Outputs 12V of power on Trigger when Aspect Ratio is set to Letterbox. 
Native: Outputs 12V of power on Trigger when Aspect Ratio is set to Native. 
Unscaled: Outputs 12V of power on Trigger when Aspect Ratio is set to Unscaled. 
Auto: Outputs 12V of power on Trigger automatically. 
 
OSD Settings 
Menu Position: Adjust menu position through this function, the available position options are at Top-Left: 
Top-Right, Bottom-Left, Bottom-Right and center of the screen. 
Menu Transparency: Change the transparency of OSD Menu, the background color of the OSD can be adjusted from 
darker to lighter if you want to display complete projected image.
 
Time Out: Set up the timer to exit OSD menu, the available options are Always On, 10 Seconds, 30 Seconds and 60 
Seconds. 
 
Message Box 
This function allows you to disable the pop-up message at bottom-right of the screen.  
						

							DU8090Z DLP Projector - User Manual 
 
37 
 
OSD MENU – SERVICE 
 
Model 
Display the project model name. 
 
Serial Number 
Display the serial number of the projector. 
 
Software Version 1 / Software Version 2 
Display the software version in the projector. 
 
Active Source 
Display the current input source information. 
 
Signal Format 
Display current input source format   
. 
H/V Refresh Rate 
Display horizontal and vertical refresh rate of the current picture. 
 
Pixel Clock 
Display pixel clock of the current input signal. 
 
Light Time 
Display accumulated usage of projection light source 
 
Thermal Status 
Display current of the thermal management components. 
Factory Reset 
The user can use this function to reset all the settings to factory default; light time. 
  
						

							DU8090Z DLP Projector - User Manual 
38 
Product Specification 
Display Type Single Chip 0.67 DLP Technology 
Brightness 8,000 
ANSI Lumens
Native Resolution WUXGA (1920 x 1200) 
Maximum Resolution  WUXGA (1920 x 1200)@60Hz (Reduced Blanking) 
Contrast Ratio  10,000:1 
Illumination Type Laser Phosphor 
Throw Ratio*  1.73 - 2.27:1 
Image Size (Diagonal) *  40 - 500 
Projection Distance *  1.45 - 24.85m (4.77ft to 81.52ft) 
Projection Lens *  F = 1.7 - 1.9, f = 26 - 34mm 
Zoom Ratio * 1.3x
Aspect Ratio  16:10 
Offset  Motorized Lens Shift 
Keystone Correction  Horizontal ±60°, Vertical ±40° ( individual adjustable range) 
Horizontal Frequency  15, 30 – 90Hz 
Vertical Scan Rate  50 - 85Hz 
Edge Blending Yes (Built-In) 
WarpingYes (Built-In)
3D Functionality  Yes (DLP® Link™, HDMI v1.4 (Blu-ray, side by side, frame packing, top and 
bottom))
 
Adjustable  
Lens Shift Range  Vertical: -30 - +50%, Horizontal: ±10% 
I/O Connection Ports HDMI v1.4a (x2) DVI-D, Component 
(5 BNC), VGA-In, 3G-SDI-In/Out, 
RS-232, VGA-Out, 3D-Sync In/Ou t, 12v Trigger, Wired Remote, 
HDBaseT™/LAN  (Shared)  
Projection Method  Table Top, Ceiling Mount (Front or Rear) 
Security Solutions Kensington® Security Slot, Security Bar,    Anti-Theft Lens Screw 
Dimensions (WxDxH)  500 x 580 x 205mm (19.7” x 22.8 x 8.1) 
Weight28kg (61.7lbs)
Available Colours  White (DU8090Z-WH), Black (DU8090Z-BK) 
Noise Level 40dB (Normal Mode) 
Power Supply  AC 100-240V, 50/60Hz 
Power Consumption  850W (Normal Mode), 675W (Eco. Mode), 
						

							DU8090Z DLP Projector - User Manual 
 
39   
Supported Signal Input Timing 
Signal Format Resolution Frame Rate 
(HZ) 
VGA, BNC HDMI / HDBaseT HD/SDI/3G 
SOG RGBHV RGBYUV 
8-bit10-bit 12-bit
PC 640x480 59.94   O O     
640x480 74.99    O  O      
640x480 85    O  O      
800x600 60.32    O  O      
800x600 75    O  O      
800x600 85.06    O  O      
848x480 47.95    O  O      
848x480 59.94    O  O      
1024*768 60    O  O        
1024*768 75    O  O        
1024*768 85    O  O        
1280x720 47.95    O  O         
1280x1024 60.02    O  O         
1280x1024 75.02    O  O         
1280x1024 85.02    O  O         
1600x1200 60    O  O         
1920x1080 47.95    O  O         
1680x1050 59.94    O  O         
1920x1200 RB  50    O  O         
1920x1200 RB  60    O  O         
1400X1050   60    O  O         
1366 x 768      60    O  O         
1440 x 900    60    O  O         
1280 x 768      60    O  O         
1280 x 800      60    O  O         
1280 x 960    60    O  O         
Apple Mac  640x480  66.59    O  O         
832x624 74.54    O  O      
SDTV 480i  59.94  O       O 
1440x480i  60      O O O O   
1440x576i  50      O O O O   
576i 50  O      O 
EDTV  480p  59.94  O  O  O O O O   
576p  50  O  O  O O O O   
HDTV  1035i  60  O  O  O O O O  O 
1080i  50  O  O  O O O O  O 
1080i  59.94  O  O  O O O O  O 
1080i  60  O  O  O O O O  O