Vivitek Projector DU8090Z User Manual

DU8090Z DLP Projector - User Manual 
 
20 
Connecting to external HDBaseT Transmitter 
The projector has a built-in HDBaseT receiver. With HDbaseT Transmitter (optional), the video, RS-232 and LAN 
signals can be sent to the projector via a single RJ-45 cable. If the HDbaseT Transmitter you purchased supports the 
input and output of the IR remote control, the control signals from the IR remote control can be sent to the DU8090Z 
projector via the RJ-45 cable. 
 
 
 
 
Note: 
 The projector supports the...

DU8090Z DLP Projector - User Manual 
 
21 
Using the projector 
 
 
Select the Input Voltage of AC Power 
There is one slide switch near AC switch, pleases switch it to according input voltage of AC power.   
 
Connecting to AC Power Supply 
The AC power cord is included in the box, plug the power cord to the AC socket on the IO panel. 
 
Turning on the Projector 
Once the projector is correctly located and the power cable and other connections are in place, it is important that the 
projector is powered...

DU8090Z DLP Projector - User Manual 
 
22  2.  Press the POWER button on the control panel or ON 
button on the remote control.   
 
3.  The Power LED and LIGHT LED flashes green till 
power on process is finished. 
 
4.  After few seconds, both LEDs keep green, the projector 
is ready for use.   
 
Turning off the Projector 
Once the projector is no longer required, it is important to shut it down correctly to avoid damage or unnecessary 
wear and tear to the projector. 
Refer to the following guide to...

DU8090Z DLP Projector - User Manual 
 
23 
Using On-Screen Display 
Using the OSD Menu 
The projector has an On-Screen Display (OSD) that lets you make image adjustments, change various settings and 
check current projector status.   
 
Navigating the OSD 
You can use the remote control or the control buttons on the projector to navigate and make changes to the OSD. 
The following illustration shows the corresponding buttons on the remote control and on the projector 
 
1.  To open the OSD, press the...

DU8090Z DLP Projector - User Manual 
 
24 
Menu Tree 
Use the following table to quickly find a setting or determine the range for a setting. 
 
Main Menu Submenu 
INPUT Input Selection HDMI1  
HDMI2 
VGA 
Component 
BNC 
DVI 
3G-SDI 
HDBaseT  
 PIP PIP Option  
  PIP Input  
  Position  
 Auto Source Off 
On  
 Color Space Auto  
YPbPr 
YCbCr 
RGB-PC 
RGB-Video  
 Aspect Ratio 5:4  
4:3 
16:10 
16:9 
1.88 
2.35 
LetterBox 
Source 
Native  
 Overscan Off  
Crop 
Zoom  
 VGA Setup H Total 
H Start 
V...

DU8090Z DLP Projector - User Manual 
 
25 
6500K 
7500K 
9300K 
Native 
 Gamma 
1.0 / 1.8 / 2.0 / 2.2 
/ 2.35 / 2.5 / S-Curve  
  Input Balance  Red Offset 
Green Offset 
Blue Offset 
Red Gain 
Green Gain 
Blue Gain  
 HSG Red 
Green 
Blue 
Cyan 
Magenta 
Yellow  
White 
Reset  
 Noise Reduction    
 Dynamic Black Off 
On  
ALIGNMENT Lens Lock  Off 
On  
 Lens Control Zoom 
Focus 
Lens Shift  
  Lens Type  Non-UST Lens 
UST Lens  
 Lens Memory Load Memory 
Save Memory 
Clear Memory  
 Center Lens Execute...

DU8090Z DLP Projector - User Manual 
 
26 
  Auto Power On  Off 
On  
 Network Standby Power 
DHCP 
IP Address 
Subnet Mask 
Gateway 
DNS 
Mac Address  
 Light Power Eco 
Normal 
Custom   
  Custom Power Level     
 Background Logo  
Black  
Blue  
 Startup Logo Off 
On  
 Remote Sensor Off  
On  
 Trigger Off  
Screen 
5:4 
4:3 
16:10  
16:9 
1.88  
2.35 
LetterBox 
Source 
Native  
 OSD Seting Menu Position 
Menu Transparency 
Time Out  
SERVICE Model     
 Serial Number    
  Software Version 1...

DU8090Z DLP Projector - User Manual 
 
27    
OSD Operation – INPUT 
Input Selection 
Use the shortcut key on the remote control or this function to select the input source, the Input options are as below. 
The available input source of the product is HDMI 1, HDMI 2, VGA, Component (BNC), HDBaseT, DVI and 3G-SDI. 
 
PIP 
This function allows you to split the screen for displaying the images from two input sources 
PIP Option 
Enable PIP by choosing “ON”, and two windows will be shown on the projected...

DU8090Z DLP Projector - User Manual 
 
28  Position 
Find preferred location of PIP window. 
   Top Left: Display sub picture at top left of the screen. 
   Bottom Left: Display sub picture at bottom left of the screen. 
   Top Right: Display sub picture at top right of the screen. 
   Bottom Right: Display sub picture at bottom right of the screen. 
   PBP: Display sub picture next to main picture, the main screen is shrined to the same size as sub picture. 
Auto Source 
The Auto Source functions “ON”...

DU8090Z DLP Projector - User Manual 
 
29 
3D 
This function is to set the 3D format and sync method. The projector detects the type of input signals and provides 
relevant options for setting. Before performing 3D setting, make sure that the input signal is connected. 
3D Format 
Off: Turn off the 3D Display Mode. When Auto, Side by Side, Top and Bottom, or Frame Sequential is selected, 
the 3D Mode will be turned on. To turn off the 3D Mode, select “Off” and press “ENTER”. 
Auto: Allow the 3D format to...