Vivitek Projector D8800 Series User Manual

41
DLP Projector - User’s Manual
3. Make any desired changes to projector settings, then Click Save .
To connect to a stand alone PC or notebook, refer to the following steps:
1.  Connect an RJ45 cable to LAN ports on the projector and the PC (Laptop).
IN SDI OUT
LAN HDMI
DVI-D
RGB
Desk Top or Notebook
2.  On the PC (Laptop), select Start -> Control Panel -> Network Connections.   

DLP Projector - User’s Manual
42
3. Right-click on Local Area Connection, and select Properties.
4 . In the  Properties window, select the General tab, and select Internet Protocol (TCP/IP).
5 .  Click Properties.
6. Click Use the following IP address.
7.   Fill in the IP address and subnet mask. Make sure the IP address of the projector and PC are in the same 
network group. For example, 192.168.0.X. Whereas X must contain a different value. Then click OK.   

43
DLP Projector - User’s Manual
8. On the control PC, open a web browser and enter the IP address of the projector.
The Projector Web Server home page displays. In the example, the projector resides at IP address 
192.168.0.100.
9. Make any desired changes to projector settings, then Click Save .
10.  Access Tera Term tool.  
 
 
 
 
 
 
 
 
 
 
 
 
 
Use RS-232 command to control the Projector.   

DLP Projector - User’s Manual
44
 
y Start Up Logo
Use   function to turn On/Off the start up logo.
 
y Trigger
The projector comes with one set of Trigger output. You can configure one devices connected to the projector via 
the trigger port to be automatically turned on when the projector is on. There will be a 2-3 second delay prior to 
activation to prevent operation of this function when the user is choosing the desired aspect ratio.
 
y 5:4:  Outputs 12V of power on Trigger when chooses the 5:4...

45
DLP Projector - User’s Manual
OSD Introduction - SERVICE
INPUTP ICTURE
Model :
Serial Number :
Software Ve rsion :
Active/PIP  Source :
Pixel Clock  :
Signal Format  :
H/V Refresh Rate :
Lamp 1  Time :
Lamp 2  Time :
Power On  Time :
Blue Only
Factory Reset DP9675QDPxA
C202XXXX00767
MD05-GD02-Ub01- 9999-31-DPNE02-D02
HDMI                         / Of
f
83 .30 MHZ
1280x800@60Hz
H: 49.578 KHZ V:  60 HZ
7 HRS
7 HRS
7 HRS
<            Of f           >
Enter
LAMPS
ALIGNMENT CONTROLSERVICE
The functions...

DLP Projector - User’s Manual
46
 
y Lamp 2 Time
Display the lamp 2 usage time. When you change the new lamp. The lamp hours will re-calculate the time.
 
y Power On Time
Display the total On time for projector. Display only.
 
y Blue Only
Enabling this option will make the projector display only blue color to facilitate the process of image inspection for 
the service personnel. For detailed instructions on how to use this function, consult a qualified service personnel.
 
y Factory Reset
Use this...

47
DLP Projector - User’s Manual
Change Lamp
The lifecycle of ordinary projection lamp typically lasts for 1200 hours before requiring replacement (different lamp con-
figurations will affect lamp life). From the OSD Menu, you can go to “OSD Introduction - SERVICE” on page 45 to check how 
long a lamp has been used. You should also replace the lamp when the projected image gets noticeably darker. Contact 
your local dealer to purchase new certified lamps for your projector.
To replace the projector...

DLP Projector - User’s Manual
48
To replace the projector lamp2
1. Loosen the fan.
2. Use a screw driver to loosen the screws as shown in 
the illustration and pull the lamp out.
3. Insert the new lamp in the direction shown in the il-
lustration into the lamp assembly; tighten the three 
screws using a screw diver and make sure the lamp 
is firmly secured to prevent the lamp from shaking 
or poor contact.
4 . Replace the fan and firmly secure the one screw on 
the fan.   

49
DLP Projector - User’s Manual
Change Lens
To replace the projector Lens
1. Remove the front cover.
2.  Press and hold the lens lock button. Support the lens 
with one hand and turn clockwise loose the lens.
3. Pull the lens backward and slide the lens out of the 
lens holder.
4 . Insert the lens that female jeck is in front of the 
male jack (upper left corner). Ensure the lens 
touches the lens holder.
5 . Secure the lens in the lens holder by turning coun-
terclockwise the lens to the “locked”...

DLP Projector - User’s Manual
50
 
„ Six models of lens for D8900(XGA)
Vivitek Part Number LensF#TRZoom Ratio
D88-ST001 Standard Lens 1.7 ~ 1.91.79 ~ 2.35 1.3
D88-WF18501 Wide Fix 1.850.8N /A
D88-WZ01 Wide Zoom 1.85 ~ 2.501.3 ~ 1.85 1.41
D88-SMLZ01 Semi Long Zoom 1.86 ~ 2.482.3 ~ 3.81 1.65
D88-LOZ101 Long Zoom1 1.85 ~ 2.413.67 ~ 5.64 1.5
D88-LOZ201 Long Zoom2 1.85 ~ 2.485.5 ~ 8.56 1.55
 
„ Six models of lens for D8010W(WXGA)
Vivitek Part Number LensF#TRZoom Ratio
D88-ST001 Standard Lens 1.7 ~...