Vivitek Projector D8800 Series User Manual

31
DLP Projector - User’s Manual
OSD Introduction - PICTURE
INPUTPICTURE
Display Mode
Contrast
Brightness
Adaptive Contrast
Saturation
Hue
Gamma
Color
Sharpness
Noise Reduction
Aspect Ratio
Oversca n
VGA Setup
Auto Sync <          Vi
deo         >
<           100            >
<            50             >
<           Of f            >
<           -----            >
<           -----            >
<           Film           >
Enter
<             0              >
<             0              >
<...

DLP Projector - User’s Manual
32
 
y Color
Use   to adjust the color temperature of the projected image.
 
y Sharpness
The adjustment of sharpness primarily changes the value of high frequency detail. Use   to adjust it.
 
y Noise Reduction
Use  to adjust the noise of the projected image. This function is suitable for the elimination of image noise 
from interleaving SD input. Generally speaking, reducing image noise will lower the value of high frequency detail 
and make the image appear more...

33
DLP Projector - User’s Manual
 
y Overscan
Some consumers may use the image that input source is not 16:9, and some programs may not display the edges 
of the image. Use this function to hide the image edge by choosing one of the following three options:
Z oom
Crop
4:3
Narro w
Nativ e
(720p) 16:9
4:3
Source image area
Edge Noise
Sc
reen (16:9)Sou
Edg
Scre
6:9
 
y VGA Setup
Use this function to set up the VGA display.
 
y Auto Sync
Use this function to set the automatic adjust setting for the incoming...

DLP Projector - User’s Manual
34
OSD Introduction - LAMPS
INPUTP ICTURE
Mode
Power
High Altitude
Custom Power Level
Lamp 1 Status  :
Lamp 2 Status  : <         Single         
>
<           Eco            >
<           Of f            >
<           -----           > OnOf fLAMPSALIGNMENT CONTROLSERVICE
 
y Mode
Use   function to select single or dual lamp mode.
 
y Power
Use   function to select Eco, normal, or custom power level.
 
y High Altitude
Use this function to control the projector’s cooling...

35
DLP Projector - User’s Manual
OSD Introduction - ALIGNMENT
INPUTP ICTURE
Projection Mode
Fan Mode
Lens Control
Lens Memory
Center Lens
W arp
Blanking
Edge Blend <          Front         
>
<         Normal         >
Enter
Enter
Execute Enter
Enter
Enter
LAMPSALIGNMENTCONTROL
SERVICE
 
y Projection Mode
Use   function to select the projection mode (Front, Rear, Ceiling + Front, Ceiling + Rear).
 
y Fan Mode
Use   function to set the fan mode (Normal, Up, Down).
 
y Lens Control
Use this function to...

DLP Projector - User’s Manual
36
 
y Pincushion / Barrel
Press   to correct pincushion/barrel distortion.
P
Press   to correct pincushion dis-
tortion to correct image.
P
P
Press   to correct barrel distortion 
to correct image.
P
 
y Top Left Corner
Press   to correct top left corner image distortion.
P
Press   to correct top left corner 
image distortion to correct image.
P
 
y Top Right Corner
Press   to correct the right corner image distortion.
P
Press   to correct top right corner...

37
DLP Projector - User’s Manual
 
y Blanking
Use this function to adjust the edges of the image and hide unwanted sections of the screen.
 
y TOP
Press   on the remote control to adjust the top blank -
ing area on the projected image.
 
y Bottom
Press   on the remote control to adjust the bottom 
blanking area on the projected image.
 
y Left
Press   on the remote control to adjust the left blank -
ing area on the projected image.
 
y Right
Press   on the remote control to adjust the right blank...

DLP Projector - User’s Manual
38
White Level
Top
Bottom
Left
Right 0
0
0
0
 
y Black Level Uplift
Black Level Uplift is used to compensate for the lack of pure black output from projectors, due to light leak -
ing to the projection screen. When projecting black , the hot area where the two images overlap project 
twice the projectors’ black output levels. 
The solution is to adjust the Black Level Uplift. First make sure that the units connected to the projectors are 
outputting black. Then increase the...

39
DLP Projector - User’s Manual
OSD Introduction - CONTROL
INPUTP ICTURE
Eco Network Power
Auto Power Off
Auto Power On
Projector Control
Network
Start Up Logo
Tr igger
Auto Search
Dynamic Blac k
Language <           Eco           
>
<            On            >
<            Of f           >
<           -----           > Enter
<            On            >
<            Auto          >
<            Of f           >
<            On            >
Enter
LAMPS
ALIGNMENTCONTROLSERVICE
 
y Eco Network Power
Use...

DLP Projector - User’s Manual
40
To connect to a network (LAN), refer to the following steps:1.  Connect an RJ45 cable to LAN ports on the projector and a router or hub on the network.
Projector
(Ethernet)
2. On the control PC, open a web browser and enter the IP address of the projector.
The Projector Web Server home page displays. In the example, the projector resides at IP address 
192.168.0.100.