ViewSonic Projector Pj1158 User Manual

Network Functions
Network	Functons
Configuring and Controlling the Projector via a Web Browser
You	can	change	the	settngs	of	or	control	the	projector	va	a	network	by	usng	a	
web	browser	from	a	PC	that	s	connected	to	the	same	network.
Failure & Warning Alerts via E-mail
The projector can automatically send an alert to specified e-mail addresses when 
the	projector	requres	mantenance	or	has	encountered	an	error.
Projector Management via SNMP
Ths	projector	s...

Network Functions
Before using the network functions…
To use the network functions of this projector, the projector must be configured to 
sut	your	network.	Consult	wth	your	network	admnstrator	before	connectng	the	
projector to your network. Incorrect network configuration of this projector may 
cause	problems	on	your	network.
Connect to the Gateway (The router/PC that forwards traffic to a destination 
outsde	of	the	subnet	of	the	transmttng	devce)	from	the...

Network Functions
Configuring and controlling the projector via a web browser
You	can	adjust	or	control	the	projector	va	a	network	from	a	web	browser	on	a	PC	
that	s	connected	to	the	same	network.
•	Internet	Explorer	5.5	or	hgher	or	Netscape	6.2	or	hgher	are	requred.
• If JavaScript is disabled in your web browser configuration, you must enable 
JavaScript in order to use the projector web pages properly. See the Help files 
for	your	web	browser	for	detals	on	how	to	enable...

Network Functions
When configuring or controlling the projector via a web browser, an ID and pass-
word	are	requred.	 There	are	two	types	of	IDs,	 Admnstrator	IDs	and	User	IDs.	
The	followng	chart	descrbes	the	dfferences	between	user	and	admnstrator	IDs.
Below	are	the	factory	default	settngs	for	admnstrator	IDs,	user	IDs	and	pass
-
words.
ItemDescriptionAdministrator IDUser ID
Network Information Dsplays	the	projector’s	current	net-work...

Settings
Settngs
Refer to the following for configuring or controlling the projector via a web brows-
er.
Example:	If	the	IP	address	of	the	projector	s	set	to	192.168.1.10:
1)		 Enter
	
[https://192.168.1.10]  nto	the	ad-
dress	bar	of	the	web	browser	and	the	
screen	n	Fg.	1	wll	be	dsplayed.
2)		 Enter	your	ID	and	password	and	clck	
[Logon].
If	the	logon	s	successful	ether	the	Fg.2	or	Fg.3	screen	wll	be	dsplayed.
3)   Click the desired...

Settings
Network Information
All	screen	mages	dsplayed	n	ths	manual	are	
screens	of	a	logon	usng	an	admnstrator	ID.
Any	admnstrator	only	functons	wll	not	be	ds
-
played	when	usng	a	user	ID.	Refer	to	the	de
-
scrptons	n	each	table.
Displays the projector’s current network configuration settings.
ItemDescription
DHCPDisplays the DHCP configuration settings.
IP Address Dsplays	the	current	IP 	address.
Subnet...

Settings
Network Settings
Displays and configures network settings.
Clck	the	
[Apply]	button	to	save	the	settngs.
• The new configuration settings are activated after restarting the net-
work connection. When the configuration settings are changed, you must re-
start 	the	 network 	connect on.	You	 can	restart 	the	 network 	connect on	by	clck ng	
[Network Restart] 	on	the	man	menu.
•	If	you	connect	the	projector	to	an	exstng	network,	consult	a	network...

Settings
Port Settings
Displays and configures communication port settings.
Clck	the	
[Apply]	button	to	save	the	settngs.
• The new configuration settings are activated after restarting the net-
work connection. The network connection must be restarted when the configu-
raton	settngs	are	changed.	 The	network	connecton	can	be	restarted	usng	
[Network Restart]	on	the	man	menu.dresses.
NOTE
ItemDescription
Network Control Port1 (Port:23)Configures command control port 1...

Settings
Mail Settings
Displays and configures e-mail addressing settings.
Clck	the	
[Apply]	button	to	save	the	settngs.
• You can confirm whether the mail settings work correctly using the 
[Send Test Mail] button.
•	If	you	connect	the	projector	to	an	exstng	network,	consult	a	network	admns
-
trator	before	settng	server	addresses.
NOTE
ItemDescription
Send Mail Clck	the	[Enable] check box to use the e-mail function. Configure the conditions for sending email...

Settings
Alert Settings
Displays and configures failure & warning alerts.
ItemDescription
Cover ErrorConfigures Cover Error alert settings.
SNMP TrapClck	the	[Enable]
	check	box	to	enable	SNMP 	Trap	alerts	for	
ths	tem.
Send Mail  Clck	the	[Enable] check box to enable e-mail alerts for this 
tem.
Mail SubjectConfigures the subject line of the e-mail to be sent.
The	length	of	the	subject	lne	can	be	up	to	255	alphanumerc	
characters.
Mail TextConfigures the text of the...