ViewSonic Projector Pj1158 User Manual

Part names
Remote control
(1)		Laser	ponter	
It	s	a	beam	outlet.
(2)	LASER	INDICATOR
(3)	LASER	button
(4)	STANDBY/ON	button
(5)	VOLUME	button
(6)	MUTE	button
(7)	VIDEO	button
(8)	RGB	button
(9)	SEARCH	button
(10)	 AUTO	button
(11)	 ASPECT 	button
(12)	POSITION	button
(13)	KEYSTONE	button
(14) MAGNIFY - ON button(15) MAGNIFY - OFF button
(16)	FREEZE	button
(17)	BLANK	button
(18) MY BUTTON - 1 button(19) MY BUTTON - 2 button
(20)	MENU	button
(21)		 Lever	swtch	:	actng	3	functons...

Setting up
Settng	up
Install	the	projector	accordng	to	the	envronment	and	manner	the	projector	wll	be	
used	n.
WARNING  ►Place the projector in a stable horizontal position. If the pro-
jector	falls	or	s	knocked	over	t	could	cause	njury	and/or	damage	to	the	projec
-
tor. Using a damaged projector could then result in fire and/or electric shock.
•		 Do	not	place	the	projector	on	an	unstable,	slanted	or	vbratonal	surface	such	
as	a	wobbly	or...

Arrangement
Refer	to	the	llustratons	and	tables	below	to	determne	screen	sze	and	projecton	dstance.
The	values	shown	n	the	table	are	calculated	for	a	full	sze	screen:	1024×768	
(a)	Screen	sze	(dagonal)
(b)	Projecton	dstance	(±10%)
(c)	Screen	heght	(±10%),	when	the	vertcal	lens	shft	s	set	full	upward
Setting up
(a) Screen size[inch (m)] 4	:	3	screen
16	:	9	screen
(b) Projection distance  [m (inch)](c) Screen height[cm...

Adjusting the projector's elevator
When	the	place	to	put	the	projector	s	slghtly	uneven	to	the	left	or	rght,	use	the	
elevator	feet	to	place	the	projector	horzontally.	
Usng	the	feet	can	also	tlt	the	projector	n	order	to	project	at	
a	sutable	angle	to	the	screen,	elevatng	the	front	sde	of	the	
projector	wthn	8	degrees.
Ths	projector	has	2	elevator	feet	and	2	elevator	knobs.	An	elevator	foot	s	adjust
-
able	whle	pullng	up...

Setting up
Connecting your devices
Be	sure	to	read	the	manuals	for	devces	before	connectng	them	to	the	projector.	
Make	sure	that	all	the	devces	are	sutable	to	be	connected	wth	ths	product,	and	
prepare	the	cables	requred	to	connect.
Please	refer	to	the	followng	llustratons	to	connect	them.
WARNING  ►Do not disassemble or modify the projector.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION  ►Turn off all devices and unplug...

Setting up
NOTE		•	Be	sure	to	read	the	manuals	for	devces	before	connectng	them	to	the	
projector,	and	make	sure	that	all	the	devces	are	sutable	to	be	connected	wth	ths	
product.	Before	connectng	to	a	PC,	check	the	sgnal	level,	the	sgnal	tmng,	and	the	
resoluton.
-   Do not connect LAN port to any network that might have the excessive voltage.
-   Some signal may need an adapter to input this projector.
-   Some PCs have multiple screen display...

Setting up
Connecting power supply
1.	Connect	the	connector	of	the	power	cord	to	the	AC	nlet	of	the	projector.
2.	Firmly plug the power cord's plug into the outlet. 
WARNING  ►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
•	Only	use	the	power	cord	that	came	wth	the	projector.	If	t	s	damaged,	contact	
your	dealer	to	newly	get	correct	one.
• Only plug the power cord into an outlet rated for...

Remote control
Putting batteries
Please	load	the	batteres	before	usng	the	remote	control.	If	the	remote	control	starts	to	
malfuncton,	replace	the	batteres.	If	you	wll	not	use	the	remote	control	for	an	extended	
perod,	remove	the	batteres	from	the	remote	control	and	store	them	n	a	safe	place.
1.	Slde	back	and	remove	the	
battery	cover	n	the	drecton	
of	the	arrow.
2.	Algn	and	nsert	the	two	 AA	
batteres	accordng	to	ther...

Changing the frequency of  remote control signal
The	accessory	 remote	control	has	the	choce	 of	the	
mode	 1	or	 the	 mode	 2,	n	 the	 frequency	 of	ts	 sgnal.	
If	 the	 remote	 control	does	not	functon	 properly,	 at
-
tempt	to	change	the	sgnal	frequency.
Please 	remember 	that 	the 	“REMOTE 	FREQ.” 	 n	
SERVICE	tem	 of	OPTION	 menu	of	the	 projector	 to	
be 	controlled 	should 	be 	set 	to 	the 	same 	mode 	as	
the	remote	control.
To 	set 	the 	mode 	of 	the...

Using as a wired remote control
The	accessory	remote	control	works	as	a	wred	remote	
control,	when	the	wred	control	port	at	the	bottom	of	the	
remote	control	connects	wth	the	REMOTE	CONTROL	
port 	on 	the 	back 	of 	the 	projector 	v a 	an 	aud o 	cable 	w th 	3.5	
dameter	stereo	mn	plugs.	
When	the	remote	control	sgnal	s	hard	to	reach	surely	to	
the	projector	n	the	envronment,	ths	functon	s	effectve.
Remote control...