ViewSonic Pjl6243 Projector User Manual

25ViewSonic PJL6243
25
Basic Operation
Remote Control Operation
Using the remote control for some frequently used operations is advisabl\
e. Just pressing one of the buttons enables you to make the desired operation quickly without calling up the On-Screen Menu.
Press the COMPUTER 1/2, VIDEO, S-VIDEO and COMPONENT buttons on the remote control to select the input source. See pages 27, 36-37 for details.
COMPUTER	1/2,	VIDEO,	S-VIDEO	and	COMPONENT		buttons
FREEZE	button
Display the input source...

26ViewSonic PJL6243
26
Basic Operation
NO SHOW button
Press the P-TIMER button on the remote control to operate the Count up/Count down function. Refer to p.50 for detail of Setting for the P-timer function.To stop the count time, press the P-TIMER button.To cancel the P-timer function, press and hold the P-TIMER button.
P-TIMER	button
Press the IMAGE button on the remote control to select a desired image mode of the screen. See pages 32, 39 for details.
IMAGE buttonNo show disappears after 4 seconds....

27ViewSonic PJL6243
27
Choose either Computer	1(RGB)	or Computer	2(RGB) by pressing the COMPUTER 1 or COMPUTER 2 button on the remote control.Before using these buttons, correct input source should be selected thro\
ugh Menu operation as described below.
1
Input Menu
2
3
Note: When the Input Search function is set to On 1   or On 2 in the Auto setup function, the input   signal will be searched automatically (p.45).
Computer 1
Remote Control
Press the MENU button to display the On-Screen Menu. Use the...

28ViewSonic PJL6243
28
Computer Input
PC System Menu
PC System Menu
Computer System Selection
This projector automatically tunes to various types of computers with its Multi-scan system and Auto PC Adjustment. If a computer is selected as a signal source, this projector automatically \
detects the signal format and tunes to project a proper image without any additional settings. (Signal formats provided in this projector are shown on page 69.)
One of the following messages may appear when:
When the...

29ViewSonic PJL6243
29
Computer Input
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total	dots, Horizontal and Vertical positions to conform to your computer.
PC adjust Menu
Auto PC Adjustment
To	store	adjustment	parametersThe adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting a Mode	(1–10) in the PC System Menu (see page 28). See also “Store” on page 31.
Note: • Fine sync,...

30ViewSonic PJL6243
30
Computer Input
PC adjust Menu
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector.  Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It\
 allows you to recall the setting for a specific computer. 
1
2
Use the Point ◄► buttons to adjust the value, eliminating a...

31ViewSonic PJL6243
31
Computer Input
Store
To store the adjusted data, select Store and then press the Point ► or the SELECT button. Move the highlight to one of the Modes 1 to 10 in which you want to store, and then press the SELECT button.
Mode free
To clear the stored data, select Mode free and then press the Point ► or the SELECT button. Move the highlight to the Mode that you want to clear and then press the SELECT button.
Note: • Display	 area	(H/V)	cannot be selected when 480i, 576i, 480p, 576p,...

32ViewSonic PJL6243
32
Computer Input
Image select Menu
IMAGE button
Dynamic
Real
Image 1
Image 2
Image 3
Image Mode Selection 
Image 4
Blackboard(Green)
Standard
Remote Control
IMAGE button
Select the desired image mode among Dynamic, Standard, Real, Cinema, Blackboard	(Green), Colorboard, Image 1, Image 2, Image 3 and Image 4 by pressing the IMAGE button on the remote control.
Standard
Picture mode with improved halftone for graphics.
Real
Blackboard	(Green)
Image	1–4
For the image projected on a...

33ViewSonic PJL6243
33
Computer Input
Image Adjust Menu
Image Adjustment
Reset
Press the MENU button to display the On-Screen Menu.  Use the Point ▲▼ buttons to select Image adjust and then press the Point ► or the SELECT button.
1
2Use the Point ▲▼ buttons select the desired item and then press the SELECT button to display the adjustment dialog box.  Use the Point ◄► buttons to adjust the setting value.
Note:• When White balance Red, Green or Blue  is    adjusted, Color temp . will change to User.•...

34ViewSonic PJL6243
34
Computer Input
This projector has the picture screen resize function, which enables you to customize the image size.
Screen Menu
Screen	Size	Adjustment
Provide the image to fit the screen size.Normal
True
Provide  the  image  in  its  original  size.  When  the  original  image  size  is  larger  or  smaller  than  the  screen  size (1024  x  768),  the  projector  enters  to  the  panning    mode  automatically.  Use  the  Point  ▲▼◄► buttons to pan the image. When adjusted, the...