Toshiba Voice Processing Vp100 Installation And Maintenance Manual

PREPARING THE PHONE SYSTEM 
2-11 
- c 
1. 
e 3. 
1. 
._ 
._ _ 
5. 
6. 
7. 
S. 
.- 
The vendor, especially for CO Centrex, may ask for the VP 100’s registration: 
FCC Registration EQ99TB-60697-VM-T 
Ringer Equivalence 0.3A 
PBX Interface RJllCorRJllW 
Line card meets FCC Part 68 
The VP 100 unit meets FCC Part 15, Class A 
UL Registration ES2470(S) 
Or other location where the VP 100 unit will be placed. Refer to the environmental requirements in 
INSTALLATION, Installation Requi;ements, in this manual....

2-12 lnstallario- znd Maintenanc? Manual 
IMPLEMENTING THE VP 100 ON PBXS WITHOUT DIL 
FEATURE 
. 
.- 
You may encounter a PBX with an older feature package that does not provide the-DIL fertture. 
The PBXs most frequently encountered without DIL are AT&T Dimension PBXs with Feature 
Packages (FP) 2, 3,-t. 5, and 7. 
.*- 
s This feature on the Dimension is called DDC for Direct Department Calling. It is only 
available on feature packages (FP) 8, 10, 12, and 15. 
If the customer’s Dimension does not have...

PREPARING THE PHONE SYSTEM 
2-13 
n Place the Console in Night Mode 
__ .- 
Even if the PBX does not have ihe DIL feature, placin 
g the console in night mode us’ually may 
be used to direct all incoming trunks to_a certain extension (such a< the VP 100 hunt group). 
. 
However, once the console has been placed in night mode, it may not be used. Direct callers 
requiring assistance (through the VP 100) to a multi-button key set for answe@ng. This 
solution therefore, is most practical for: 
. 
Smaller...

‘3 
.- CONFIGURATION APPLICATIONS 
.- 
TERMINAL 
Chapter Contents 
Section Description Page ’ 
3.1 
_. _ 
3.2 
3.3 
3.4 
-. . 
Appendix A VP CAT @erview 
............................................................................................................................ 3-l 
DOS Information ........................................................................................................................ 3-1 
VP CAT Program Description...

1 ._ 
INTRODUCTION 
_- _ 
_ 
This chapter explains how to set up a PC for use as CL- VP Configumtion Application Terminal (C;\T). 
Setup and basic operation of the CAT are explained 1 this chapter. For information about DOS and DOS 
commands, refer to the manuals that were provided G:-h your PC. or contact your PC vendor. 
The CAT is used to initiate the procedures described 3 this chapter. The CAT is an IF&i compatible PC 
with a floppy drive and an internal hard disk drive. 
- _ 
l The CAT floppy drive...

CONVENTIONS: 
.: 
To indicate the difference between the text in this chapter. the following conventions are follou-&. 
__ 
. . _ Text This is normal text in this chapter. 
VP 100 and DOS 
system prompts The VP 100 system prompts and DOS prompts are re@esented in this 
type: 
C:\VMXCAT> 
VP 100 screen 
sample 
User entries within 
VP 100 screens 
‘j%e VP 100 system commands and DOS commands that you typ.k are 
represented in this type: 
.M USER 
.MUSER 
1 Enter current MAILBOX &I&H. 
:50@ 
Enter each...

Quick Reference Guide .- . 
Configuration 
.- 
Applications Terminal 
Tips and Notes 
Sta_rting the CAT 
The CAT pro_gram starts automatically each time the PC’s power is turned ON. 
Restarting the PC 
Iffor 
any reason the CAT program becomes inoperative, the CAT can be reset by holding down the following keys 
simuhaneously. This reset is similar to turning the PC’s power OFF then ON. 
Starting the VMX CAT Program from DOS - 
Move into the VP CAT Directory. 
Type: 
From the C:L 
prompt, type: 
-. 
....

- Quick Reference Guide 
..- . 
Configuration Application& Terminal 
Tips and Notes 
Commonly Used DOS Prompts 
I%% 
provides a prompt to indicate when it is ready to receive and process commands. The following are examples of DOS 
prompt information: 
Prompt Description 
c:> DOS prompt, not indicating what directory is selected. Most likely, the VP CAT software has not been 
installed or the PC was not rebooted after VP CAT software was installed. 
C:b DOS prompt with the mot directory selected....

., CONFIGURATION APPLICATIONS TERM ?IAL 3-l 
VP CAT OVERVIEW 
__ 
.- The Configuration Applications Terminal (referred to as CAT) is a computer that combines Toshiba 
approved IBM PC compatible hardware and Toshiba supplied CAT softvvare. 
b WARNING 4 
The hardware component of the CAT should be dedicated exclusively to 
installing and maintaining Toshiba products. Any application so’fiware. 
programs, or files present on the PC hard disk drive or in RAM (memory) are 
not recommended by Toshiba and they...

3-2 installation arc Maintenance Manual 
_ 
- Backup and Restore VP 100 Greetings, Names, Script, and Sequential Messages. 
) 
- Archive and Recover VP 100 System from floppy diskette. 
_ _ - Update VP 100 System Software. 
- Beginning with Rel. 6.1, add a prompt set in a second language to the VP 100. 
CAT Terminal 
Emulation Terminal emulation allows the CAT to communi&e with rhe VP 100 
directly through a cabled connection or remotely thropgh a modem. 
Characters typed on the CAT keyboard are sent to...