Toshiba Strata Vie General Description Manual

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 20 
PROGRAM 104 
OCC AUTHORIZATION CODE LENGTH #l 
1) Lock in the SET switch on the HKSU. 
the authorization 
o-digit number is LEDs as shown below. 
Initialized Data: Blank (AD1 flashing). 
X = LED on 
66) Go to Step 2 in aziher program table 
. . . or . . 
6C) Transfer data into working memory per SET LED goes off. 
Paragraph 02.06. Station 17 REP LED goes off. 
-33-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 21 
PROGRAM 105 
EQUAL 
ACCESS #2 
1) Lock in the SET switch on the HKSU. 
4) Refer to the System Record Sheet. This pro- 
gram registers the second equal access (OCC) 
number used by the system. This five-digit As each digit is entered, the entry is verified by 
LEDs as shown below. 
Initialized Data: Blank (AD4 flashing). 
X = LED on 
All LEDs off = no data 
with this program 
6B) Go to Step 2 in a:ther program table 
. . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off.  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 22 
PROGRAM 106 
OCC AUTHORIZATION CODE LENGTH #2 _ 
1 SET LED on. 
1) Lock in the 
SET switch on the HKSU. I 
Station 17 REP LED on. 
System is in program mode. 
wo-digit number is LEDs as shown below. 
Initialized Data: Blank (AD1 flashing). 
X = LED on 
All LEDs off = no data 
with this program 
or 
. . . 
6B) Go to Step 2 in another program table 
. . . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP L.ED goes off. 
-35-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY1986 
TABLE 23 
 
PROGRAM 
1X0 
TOLL RESTRICTION CLASS PARAMETERS 
1) Lock in the SET switch on the HKSU 
2) Depress the m key on station 17. 1 SET LED on. 
Station 17 REP LED on. 
System is in program mode, 
Normal functions halt on station 17. 
SPKR LED steadv on. 
3) Dial 0 a 1 on the dial pad. 
(X = Restriction class 1 - 4) 
I 
SPKR LED flashes continuously. 
The various LEDs (see below) will indicate pres- 
4) Refer to the System Record Sheet. 
5) Depress them key to place new data in 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per 
Paragraph 02.06. An X on the record sheet means the LED should 
be on. 
Ail station 17 LEDs (except REP) go off. 
SET LED goes off. 
Station 17 REP LED goes off. 
* - 
New 
data is stored. nrevious data is erased 
A 
-36-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 24 
PROGRAM IXY 
TOLL RESTRICTION CLASS AREA CODE ENTRY 
(LCD TELEPHONE) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
2) Depress the m key. Normal functions halt on station 17. 
LCD is blank. 
SPKR LED steady on. 
LCD is blank. 
3) Dialn 1 ~(Allow),~ a fl(Deny)orD a l(Dis- SPKR LED flashes continuously. 
play) as required. (X =Restriction class 1 - 4). LCD displays dialed number. 
4) Press 1 key. 1 X 2 = LCD is blank. 
1 X 3 = LCD is blank. 
1 X 4 = LCD displays all allowed codes. 
5) Enter first area code in range sequence (start) LCD displays code entered. 
6) Depress p key.* LCD shifts left to provide space for net code. 
7) Enter final area code in range sequence (stop).* LCD displays code entered. 
8) Depress fl key. LCD is blank. 
9) Return to step 5 to enter additional area codes. 
10) Depress the m key to place new data in All station 17 LEDs (except REP) go off. 
memory. 
11A) Go to Step 2 in another program table 
. . . or . . . 
116) Transfer data into working memory per 
Paragraph 02.06 SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
“Skip steps 6 and 7 if only one area code in sequence is being entered. 
-37-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 25 
PROGRAM 1X2 
TOLL RESTRICTION CLASS OFFICE CODE ENTRY 
(LCD TELEPHONE REQUIRED) 
1) Lock in the SET switch on the HKSU. 
ns 
halt on station 17. 
!I) 
Press 1 key. 
Paragraph 02.06. 
*Skip steps 6 and 7 if only one area code in sequence is being entered. 
-3s  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 26 
PROGRAM 1 Xl 
AREA/OFFICE CODE EXCEPTION TABLE SELECTION 
SET LED on. 
1) Lock in the 
SET switch on th.e HKSU. Station 17 REP LED on. 
System is in program mode. 
2) Depress the m key on station 17. 
3) Dial 0 1 0 on the dial pad. 
(X = Restriction class 1 - 4) Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
The various LEDs (see below) will indicate pres- 
ent data. 
4) Refer to the System Record Sheet. An Xon the record sheet means the LED should 
be on. 
5) Depress them key to place new data in 
memory. All station 17 LEDs (except REP) go off. 
6A) Go to Step 2 in another program table 
. . . or . . 
66) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
-39-  
						

							PROGRAMMING PROCEOlJRES 
SECTION 300-006-300 
MAY 1986 
TABLE 27 
PROGRAM 2XY 
AREA/OFFICE CODE EXCEPTION TABLE 
(LCD TELEPHONE REQUIRED) 
1) Lock in the SET switch on the HKSU. 
-_ 
2) Depress the m key. 
3) Dial 1 a 0 
X =Table 
1 - 8 
SET LED on. 
Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
LCD is blank. 
SPKR LED steady on. 
LCD is blank. 
LCD displays dialed number, then shifts left to 
provide space for next entry (or displays current 
1 area code). 
4) Enter area code. 
_--- 
5) Depress- key. 
6) Depress the m key. LCD clears and displays area code entered. Binary 
data is shown on INT, COl, C02, CO3 keys/LEDs. 
LCD is blank. 
SPKR LED steady on. 
LCD is blank. 
7) Dial 1 a 1 (Allow), i u 8 
(Delete) or 1 fl 1 
(Display). SPKR LED flashes continuously. LCD displays 
X = Table 1 - 8. 
dialed number. 
8) Depress 1 key. 2 X 2 = LCD is blank. 
2 X 3 = LCD is blank. 
2 X 4 = LCD 
displays all currently programmed 
9) Enter first off ice code in range sequence (start). LCD displays code enter. 
10) Depress p key.* LCD shifts left to provide space for net code. 
11) Enter final area code in range sequence LCD displays code entered. 
[stop)? 
12) Depress n key. LCD is blank. 
13) Return to step 9 to enter additional office 
14) Depress the m key to place new data in 
memory. 
15A) Go to Step 2 in another program table 
. . . or . . . 
15B) Transfer data into working memory per 
Paragraph 02.06 All station 17 LEDs (except REP) go off. 
SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previpus data is erased. 
*Skip steps 
10 and 11 if only one area code in sequence is being entered.  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 28 
PROGRAM 190 
PBX BACK-UP 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
m SPKR LED steady on. 
2) Depress the . 
3) Dial 0 1 1 on the dial pad. SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the m keys, turn the associated LEDs be on. 
on 
or off, as required. Each CO key/LED If the LED is already on, depressing the asso- 
represents itself-that is, if CO 1 LED is on, the ciated key will turn it off and vice versa. LEDs 
system assumes that the CO 1 line is con- may be turned off and on until the desired pat- 
netted to a PBX line and will cause features tern is set. 
such as Toll Restriction and Automatic Dialing 
to function accordingly. 
5) Depress them key to place new data in All station 17 LEDs (except REP) go off. 
memory. 
6A) Return to Step 2 in order to continue 
with this program 
. . . or . . . 
6B) Go to Step 2 in another program table 
. . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
-4l-  
						

							PROGfUUUlMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 29 
PROGRAM 19X 
PBX ACCESS CODES 
1) Lock in the SET switch on the HKSU. 
em IS In program mode. 
AD 
1 LED will flash. 
l If the access code is a single digit, enter 1 
as the second digit. 
0 If all combinations following a particular 
X = LED on 
All CEDs off = no data 
5) Depress them key to place new data in 
memory. 
6A) Return to Step 2 in order to continue 
with this program 
6B) Go to Step 2 in aonbther program table All station 17 LEDs (except REP) go off. 
. . or . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off, 
New data is stored, previous data is erased. 
-42-