Toshiba Strata Vie General Description Manual

							Strata VI* 
SYSTEM RECORD 
MAY1988 
PROGRAM 2XY-TOLL RESTRICTION AREA/OFFICE CODE EXCEPTION TABLE 
1 OFFICE CODES 
Table 
(1 -8) 
Area Code 
X = table 1 - 8 
Y = 1 (area code) 
2 (office codes added) 
3 (office codes deleted) 
4 (display) 
I 
I 
I I I 
1 
I I I I I 1 
I 
I I I I 1 
NOTE: Initialized Data: Allow 000-999 
Use multiple sheets as required Sheet 
__-_ of A_ 
-9-  
						

							Strata VI, 
SYSTEM RECORD 
MAY 1986 
P 
PROGRAM 190 
PBX BACKUP 
CO LINE 1 X 
CO6 1 
X = Connected’to PBX line 
(LED on) 
Initialized Data: All LEDsoff 
PROGRAM 19X 
PBX ACCESS CODES - 
Enter the Access Codes (Maximum: 8) 
Initialized Data: AD1 flashing 
NOTE: 
If the access code is a single digit, enter “+” in the 
second column. If all combinations following a particu- 
lar Ist digit are to be considered access cddes fe:g., 9 7, 
92,93, etc.), enter ‘D” (don’t care) in the 2nd column. 
PROGRAM 3XX-STATION CO LINE ACCESS 
X = Select (LED on) Initialized Data: All LEDs on 
PROGRAM 4XX-STATION TVPE ASSIGNMENT 
STATION NUMBERS 
XX = Station number 
Initialized Data: CO1 and AD1 LEDs on; all other LEDs off 
-lO-  
						

							strata VI= 
SYSTEM RECORD 
MAY 1986 
PROGRAM 4#XX-STATiON FLEXWE KEY ASSIGNMENTS 
0 1 INT 1 INT 1 INT 1 INT I INT I INT / INT I INT 
NOTES. 
1. Each code (except 
l for AD) can only be assigned once per EKT. If assigned more than once, 
keys become AD keys. Refer to Table 32 for feature codes. 
2. Use multiple sheets as required. Sheet 
-__. of ~_.__  
						

							Strata VI, 
SYSTEM RECORD 
MAY 1986 
PROGRAM 5XX-STATION CLASS OF SERVICE #1 
KEY/LED 
PAU 
AD7 
AD6 
AD3 Door Phone C ring 
I 
CO6 1 Grow Paae 1 
co5 
co4 
co3 
co2 
co1 Allowed 
MIC on at start of call 
MIC key lock 
INT Speakerphone Enable 
III,,,,,,,,, 
Initialized Data: INT and CO5 LEDs on; all other LEDs off 
-12-  
						

							stratd?9 VI, 
SYSTEM RECORD 
MAY 1986 
PROGRAM 5#XX-STATION CLASS OF SERVICE #2 
I 
iNT 
NOTE: Automatic Dialing Allowed 
initialized Data: AD7, 
CO1 , INT LEDs on; all other LEDs off 
Only one selection possible per station; lowest selection has priority. 
“Hold Recall Time Code 
KEY/LED Prog. 05 16 Sec. 32 Sec. 48 Sec. 64 Sec. 96 Sec. 128 Sec. 160 Sec. 
AD3 
X X 
X X 
AD2 X X X X 
AD1 X X X X 
PROGRAM 6Xx-STATION TOLL RESTRICTION CLASS 
co3 Class 1 l 
co2 Restrict 0 or 1, 1 st and 2nd diglt 
co1 Allow 1 + O/C only 
INT 
No restriction 
A 
Initialized Data: INT LEDm; all other LEDs off 
* See Toll Restriction 
Programs 100, 1 Xl, 1 XY, 1 Xi! and 2XY. 
-13-  
						

							Strata VI, 
SYSTEM RECORD 
MAY1986 
A- C_ 
PROGRAM 7XX-STATION OUTGOING CALLRESTRICTION 
X = Select (LED on) 
Initialized Data: All LEDs off 
PROGRAMIXX-CORlNGlfiGASSIGNMENTS-DAY 
X = Select (LED on) Initialized Data: Station lo-all LEDs on; all other LEDs off 
NOTE: 
Each line can ring on only eight stations. If more than eight areprogrammed. only the 
eight stations with the lowest station numbers will ring. 
PROGRAM 8#xx-co R~NG~NGAsS~GN~~IENTS-DAYS 
NOTE: X = Select (LED on) Initialized Data: All LEDs off 
Each line can ring on only eight stations. If more than eight areprogrammed, only the 
eight stations with the lowest station numbers will ring. 
-14-  
						

							strata VI, 
SYSTEM RECORD 
MAY 1986 
PROGRAM 9Xx-CO RINGING ASSIGNMENTS-NIGHT 
X = Select (LED on) 
Initialized Data: Station lo-all LEDs on; all other LEDs off 
NO TE: 
Each line can ring on only eight stations. If more than eight areprogrammed, only the 
eight stations with the lowest staGon numbers will ring, 
-15-  
						

							TOSHIBA 
TECHNICAL BULLETIN 
‘. 
TB 000-8603 
November 7, 1986 Page 1 of 1 
Carbon Handset Instkllation 
All 6000-series electronic key telephones (EKTs) are factory-equipped 
with dynamic handsets. If a carbon handset is desired, an EKT modification 
is necessary. 
With the exception of the Single-Line EKT, the following 
modification is applicable to all 6000-series EKTs. 
1) Remove the four screws holding the EKT base cover. 
2) Remove the base cover. 
3) On the exposed PCB, cut jumpers 
W2 and W3 (also marked 
“CARBON”). See Figure 1. 
NOTE. 
Figure 1 shows the locations of the W2 and W3 jumpers for both 
handsfree answerback (HFU) and speakerphone (SPF) EKTs. 
4) Reinstall the base cover and its four screws. 
5) Replace the dynamic handset with the carbon handset. 
-----__ 
LOCATION 
ON HFU 
BOARD 
Toshiba America, Inc. Telecommunication Systems Division 
2441 Michelle Drwe, Tustin. CA 92680 171Ai fiRQ-~*a7