Toshiba Strata Vie General Description Manual

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 2 
INITIALIZED DATA (continued) 
05 Program 
Automatic Recall From Hold Timing 0#5 Program 
Camp-on Timeout 
Recall time = 32 seconds Timeout = 32 seconds 
CO LINE OPTIONS 
06 Program 
Automatic Release On Hold Enable 
Disabled = All CO lines 
07 Program 
Automatic Release On Hold Timing 
ESS Timing = All CO lines 
09,09X Program 
CO Line Group Selection 
Dial 9 group = All CO lines 
0#9 Program 
OPL Line Hunting 
Hunting = Not assigned 
100 Program 
Toll Restriction System Parameters 
(Dialing Plan) 
Plan selected = AC + NNX 1 + O/C 
101 Program 
Toll Restriction Disable 
No restriction = All CO lines 
102 Program 
Forced Account Code Check 
No check = All CO lines* 
103 Program 
Blank 
Blank 
Blank Equal Access & OCC #I 
104. Program 
OCC Authorization Code #I 
105 Program 
Equal Access or OCC #2 106 Program 
OCC Authorization Code #2 
Blank 
1 X0 Program 
Toll Restriction Class Parameters 
01 or 011 = Allowed 
0 + = Allowed 
AC f 555 = Not allowed 
Blank 1 XY Program 
Area Code Table 
Blank 1 X2 Program 
Office Code Table 
1 Xl Program 
Toll Restriction Class Area/Office Code 
Exception Table Selection 
Selected = None 
2XY Program 
Area/Office Code Exception Table 
Blank 
190 Program 
PBX Backup 
CO Operation = All CO lines 
19X Program 
PBX Access Codes 
Codes = None assigned 
3XX Program 
Station CO Line Access 
Access allowed = All lines, all stations 
-13-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 2 
INITIALIZED DATA (continued) 
STATION OPTIONS 
4XX Program 
Station Type Assignments 
1 O-key assigned = All stations 
CO 1 Start = All stations 
4#XX 
Program 
Station Flexible Key Assignment 
Assignment = Basic key strip 
5XX 
Program 
Station Class of Service #l 
Privacy Override = Not allowed, all stations 
DND Override = Not allowed, all stations 
Executive Override= Not allowed, all stations 
Door phone ring A, B, C = Not selected, all 
stations 
Group Page 84 = Not included 
Group Page 83 = Not included 
Group Page 82 = Not included 
Group Page 81 = Not included 
All Call Page = Allowed, all stations 
Room Monitor = Warning tone, all stations 
Handsfree Answerback = Not allowed, all sta- 
tions 
MIC ON/idle mode = OFF, all stations 
MIC key lock = Momentary, all stations 
Speakerphone = Allowed, all stations 
5#XX 
Program 
Station Class of Service #2 
Station-to-station message with LCD = Al- lowed, all stations 
Forced Account Code = Not required, all sta- 
tions 
Hold Recall Time = Per 
Program 05 
Automatic off-hook selection = No selection, all 
stations 
Ringing line preference = Selected, all stations 
Automatic dialing =‘Allowed, all stations 
6XX 
Program 
Station Toll Restriction Classification 
No 
Restrictions = All stations 
7XX 
Program 
Station Outgoing Call Restrictions 
No 
Restrictions = All stations 
8XX 
Program 
CO Ringing Assignments-Day 
Assignrnent = All lines ring station 10 
8#XX 
Program 
CO Ringing Assignments-Day 2 
Assignment = None 
SXX 
Program 
CO Ringing Assignments-Nite 
Assignment = All lines ring station 11 
02.84 The table and page numbers for the 
various programs follow. 
-14-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 
1986 
Table Title 
Program 
Page 
3 
4 
: 
7 
8 
9 
10 
11 
12 
13 
14 
15 
16 
17 
18 
19 
20 
21 
22 
23 
4’: 24 
..- 
25 
26 
27 
28 
29 
30 
31 
z: 
34 
35 
36 
37 
38 
39 System Assignments (Basic) 
System Assignments (Options) 
Account Code Digit Length 
System Assignments (Options) 
VCOU MF/DP Outpulsing Selection 
Automatic Recall From Hold Timing 
Camp-on Timeout 
AROH Enable 
AROH Timing 
Night Ring Over External Page 
Single CO Line (Dial 9) Group Selection 
Four CO Line Group Selection 
OPL Line Hunting 
Toll Restriction System Parameters 
Toll Restriction Disable 
Forced Account Code Check 
Equal Access or Other Common Carrier (OCC) #l 
OCC Authorization Code #l 
Equal Access or Other Common Carrier #2 
OCC Authorization Code #2 
Toll Restriction Class Parameters 
Toll Restriction Class-Area Code 
Toll Restriction Class-Office Code 
Toll Rest. Class (AOC) Exception Table Selection 
Area/Office Code Exception 
PBX Backup 
PBX Access Codes 
Station CO Line Access 
Station Type Assignment 
Station Flexible Key Assignment 
Station Class of Service #l 
Station Class of Service #2 
Toll Restriction Classification 
Station Outgoing Call Restriction 
CO Ringing Assignments-DAY 
CO Ringing Assignments-DAY 2 
CO Ringing Assignments-NITE‘ :: 
0#2 
03 
04 
05 
0#5 
06 
Ct& 
09 
09x 
0#9 
100 
101 
102 
103 
104 
105 
106 
1x0 
1XY 
1xz 
1x1 
2XY 
190 
19x 
3xX 
4xX 
4#xx 
5xX 
5#xx 
6XX 
7xX 
8XX 
8#XX 
9xX 16 
17 
18 
19 
20 
21 
22 
23 
24 
25 
26 
27 
28 
29 
30 
31 

						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 3 
PROGRAM 01 
SYSTEM ASSIGNMENTS (BASIC) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
2) Depress the m key on station 17. 
3) Dial 4 0 on the dial pad. Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
The various LEDs (see below) will indicate pres- 
ent data. 
4) Refer to the System Record Sheet. 
Using the various keys, turn the associated 
LEDs on or off, as required. The detailed mean- 
ing of each key/LED is shown below. 
NOTE. An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
. . . or . . . 
66) Transfer data into working memory per 
Paragraph 02.06. 
1 
“If the AD6 LED is off in this program, see Program 09; if AD6 LED is on, see Program 09X. 
-16-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 4 
PROGRAM 02 
SYSTEM ASSIGNMENTS (OPTIONS) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
2) SPKR LED steady on. 
3) Dial 0 1 on dial pad. SPKR LED flashes continuously. 
The various LEDs (see below) will indicate pres- 
ent data. 
4) Refer to the System Record Sheet. 
Using the various keys, turn the associated 
LEDs on or off, as required. The detailed mean- 
ing of each key/LED is shown below. 
NOTE: 
An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
if any key/LED is not shown, it is not used 
KEY/LED LED ON LED OFF < 
DND OPX#21 Eusy 
Not busy 
co4 Display dialed number (1 minute) 
15 seconds 
CO2” Night Ring over External Page Allowed Not Allowed 
co1 BGM over External Page Allowed Not Allowed 
INT External Page Included with All Call Page 
Not Included 
5) Depress them key to place new data in All station 17 LEDs (except REP) go off. 
memory. 
6A) Go 
to Step 2 in another program table 
. ..or... 
66) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
* If the CO.2 LED is turned on in this program, Program 0#8 must also be run.  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 5 
PROGRAM 0#2 
ACCOUNT CODE DIGIT LENGTH ASSIGNMENT 
SET L.ED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
2) Depress the m key on station 17. 
3) Dial a fl 1 on the dial pad. Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
The various LEDs (see below) will indicate pres- 
ent data. 
4) Refer to the System Record Sheet. Using If the LED is already on, depressing the asso- 
the various keys, turn the associated LEDs on ciated key will turn it off and vice versa. LEDs 
or off, as required. The detailed meaning of may be turned off and on until the desired pat- 
each key/LED is shown below. tern is set. INT, 
CO1 , C02, CO3 & CO4 will light 
to display data in binary form. 
NOTE. * 
I. Depressing the 1 key displays the data without changing it. 
2. To clear existing data without entering a new number, depress the 1 key-two times. 
3. fnitialized Data: 6 digits. . 
All LEDs off = no data 
! 1~ t 1x1 1x1 1x1 1x1 bd b’ 
5) 
Depress them key to place new data in All station 17 LEDs (except REP) go off. 
memory. New data is stored, previous data is erased. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per 
Paragraph 
02.06. SET LED goes off. 
Station 17 REP LED goes off.  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 6 
PROGRAM 03 
SYSTEM ASSIGNMENTS (OPTIONS) 
SET LED on. 
1) Lock in the 
SET switch on the HSKU. Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
m key on station 17. 
2) Depress the 
l 
3) Dial m a on the dial pad. SPKR LED flashes continuously. 
CO, DND & MW/FL LEDs will be on according 
to present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using the various keys, turn the associated. 
be on. 
LEDs on or off, as required. The detailed mean- 
ing of each key/LED is shown below. If the LED is already on, depressing the asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
NOTE. 
. . . 
or . . . 
6B) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, 
previous data is erased. 
-19-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 7 
PROGRAM 04 
VCOU MF/DP OUTPULSING SELECTION 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
2) Depress the w key on station 17. 
3) Dial m a on the dial pad. 
4) Refer to the System Record Sheet. 
Each CO line represents itself: 
l LED OFF = DTMF 
B LED ON = DP Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
5) Depress them key to place new data 
All station 17 LEDs (except REP) go off. 
in memory. 
* 
6A) Return to Step 2 in order to continue with 
this program 
66) Go to Step 2 in.&%& program table 
. . , or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
-2o-  
						

							TABLE 8 
PROGRAM 05 PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1966 
AUTOMATIC RECALL FROM HOLD TIMING 
(This program is used only if MW/FL, AD I and AD 2 LEDs are ALL off in Program 5Xx.) 
SET LED on. 
1) Lock in the SET switch on the HKSU 
. 
2) Depress them key on station 17. 
3) Dial g 1 on the dial pad. Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
An INT, CO or ACB LED will be on according to 
present data. 
4) Refer to the System Record Sheet. 
Using the various keys, turn one associated 
LED on or off, as required. The detailed mean- 
ing of each key/LED is shown below. 
NOTE: An X on the record sheet means the LED should 
be on. 
Only one LED is permitted to be on, depressing 
another key will turn that LED on and turn off 
the previous LED. 
If any key/LED is not shown, if is not used. 
, KEY/LED LED ON * 
ACB 
160 seconds 
CO6 128 seconds 
co 5 96 seconds 
co4 64 seconds 
co 3 
48 seconds 
co 2 
32 seconds 
co 
1 16 seconds 
INT 
No Recall 
5) Depress the m key to place new data in All station 17 LEDs (except REP) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
6B) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
-2l-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 9 
PROGRAM 0#5 
CAMP-ON TIMEOUT 
SET LED on. 
1) Lock in the SET switch on the HKSU . 
2) Depress the m key on station 17. 
3) Dial 1 fi g on the dial pad. Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
The INT or a CO LED will go on according to 
present data. 
4) Refer to the System Record Sheet. 
Using the various keys, turn one associated 
LED on or off, as required. The detailed mean- 
ing of each key/LED is shown 
below. 
NOTE. 
An X on the record sheet means the LED should 
be on. 
Only one LED is permitted to be on, depressing 
another key will turn that LED on and turn off 
the previous LED. 
lf any key/LED is not shown, it is not used. 
KEY/LED 
LED ON 
co3 64 seconds 
4 
co 2 48 seconds 
co 1 32 
seconds 
INT 
16 seconds 
5) Depress the m key to place new data in All station 17 LEDs (except REP)go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . 
or . . . 
66) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased.