Toshiba Strata Vie General Description Manual

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 10 
PROGRAM 06 
AUTOMATIC RELEASE ON HOLD ENABLE 
SET LED on. 
1) Lock in the 
SET switch on the HKSU . Station 17 REP LED on. 
System is in program mode. 
2) Depress them key on station 17. 
3) Dial 1 tj] on the dial pad. 
4) Refer to the System Record Sheet. 
Using the m keys, turn the associated 
LEDs on or off, as required. Each CO key/LED 
represents itself-that is, if CO 1 LED is on, 
CO 1 will have AROH during normal opera- 
tion. If CO 1 LED is off, AROH will not function 
on that line. 
5) Depress the m key to place new data in 
memory. Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
All station 17 LEDs(except REP)gooff. 
6A) Return to Step 2 in order to continue with 
this program 
. ..or... 
6B) Go to Step 2 in another program table 
. . . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
-23-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 11 
PROGRAM 07 
AUTOMATIC RELEASE ON HOLD (AROH) TIMING 
SET LED on. 
1) Lock in the 
SET switch on the HKSU Station 17 REP LED on. 
System is in program mode. 
2) Depress the m key on station 17. 
3) Dial D 0 on the dial pad. 
4) Refer to the System Record Sheet. 
Using the [r9 keys, turn the associated 
LEDs on or off, as required. Each CO key/LED 
represents itself-that is, if CO 
1 LED is on, 
CO -1 will have XB (crossbar) timing for 
AROH. If CO 1 LED is off, ESS timing will be 
used on that line. 
5) Depress the m key to place new data 
in memory. Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
An Xon the record sheet means the LED should 
be on. 
If the LED is already on, depressing the asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired 
pattern is set. 
All station 17 LEDs (except REP) go off. 
6A) Return to Step 2 in order to continue 
with this program 
, ._ 
6B) Go to Step 2 in aonbther program table 
. . . or . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
NOTE. 
This program will have no meaning unless AROH is enabled via Program 06. 
1 
-24-  
						

							PROGRAlUlUlING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 12 
PROGRAM 0#8 
NIGHT RING OVER EXTERNAL PAGE 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
key on station 17. 
3) Dial B fl 1 on the dial pad. 
4) Refer to the System Record Sheet. 
This program assigns either Ring or No Rin 
for 
each CO line in night operation. Using the 
b 
l 
keys, turn the associated LEDs on or off, as 
required. Each CO key/LED represents itself- 
that is, if CO1 LED is on, when the system is in 
night operation, incoming calls over that CO 
iine will ring over the external page; if CO1 LED 
is off, incoming calls over that CO line will not 
ring in night operation. 
5) Depress them key to place new data in 
memory. Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the as- 
sociated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
Initialized Data: All LEDs on. 
. 
All station 17 LEDs (except REP) go off. 
6A) Return to Step 2 in order to continue 
with this program 
or 
. . . 
66) Go to Step 2 in another program table 
. . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
NOTE. 
Use this program only if 
CO2 LED is on in Program 02. 
-25-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1966 
TABLE 13 
PROGRAM 09 
SINGLE CO LINE (DIAL 9) GROUP SELECTION 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
m SPKR LED steady on. 
2) Depress the 
l 
3) Dial fl g on the dial pad. SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using them keys, turn the associated LEDs be on. 
on or off, as required. Each CO key/LED 
If the LED is already on, depressing the as- 
represents itself-that is, if CO1 LED is on, CO 
ociated key will turn it off and vice versa. LEDs 
1 will be included in the “Dial 9” group for 
may be turned off and on until the desired pat- 
random selection by a single line (OPX) exten- 
tern is set. 
sion or by any station using Trunk Queuing. If 
CO1 LED is off, CO1 can be accessed onl b 
dialing 0 1 0 at the OPX station or by the 
&!I 
l 
key on an EKT. I 
5) Depress them key to place new data in All station 17 LEDs (except REP) go off. 
memory. 
6A) Return to Step 2 in order to continue 
with this program 
. . 
66) Go to Step 2 in a%her program table 
. . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
NOTE: 
Use this program only if the 
A06 LED is turned off in Program 0 1. 
-26-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 14 
PROGRAM 09X 
FOUR CO LINE (DIAL 91,92,93,94) GROUP SELECTION 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
2) Depress the m key on station 17. 
SPKR LED steady on. 
3) Dial B u a on the dial pad. (X = 1, 2, 3 or 4 
SPKR LED flashes continuously. 
de ending upon the group bein 
Al b defined). Dial 
for “dial 91” group; 1 1 CO LEDs go on according to present data. 
for “dial 92” 
group, etc. 
4) Refer to the System Record Sheet. 
Using the m keys, turn the associated LEDs 
on or off, as required. Each CO key/LED 
represents itself-that is, if CO1 LED is on, CO 
1 will be included in the “Dial 9X” group for 
random selection by a single line (OPX) exten- 
sion or by any station using Trunk Queuing. If 
CO1 LED is off, CO 1 can be accessed onl b 
dialing 0 B i at the OPX station or by the 
ti 
l 
An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the as- 
sociated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
-7. 
key on an EKT. 
5) Depress them key to place new data in 
memory. All station 17 LEDs (except REP) go off. 
6A) Return to Step 2 in order to continue 
with this program 
6B) Go to Step 2 in aonbther program table 
. . . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. 
SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
NOTE: 
Use this program only if the AD6 LED is turned on in Program 07. 
-27-  
						

							PROGRAMMlNG PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 15 
PROGRAM Q#9 
OPL LINE HUNTING 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
2) Depress the m - key on station 17. 
3) Dial 1 4 a on the dial pad. 
4) Refer to the System Record Sheet. 
Using the m keys, turn the associated LEDs 
on or off, as required. Each CO key/LED 
represents itself-that is, if COs 1 & 2 LEDs are 
on, an incoming call at CO2 will ring the CO 1 
OPL station if CO1 is idle. Lines must function 
in groups of three as they appear on the HOLB, 
and the lowest numbered line sncrsa be 
selected. Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs qo on according to present data. 
An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the as- 
sociated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. e 
5) Depress the HOLD key to place new data in 
memory. All station 17 LEDs (except REP) go off. 
6A) Return to Step 2 in order to continue 
with this program 
6B) Go to Step 2 in a$her program table 
. . . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
-28-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 
1986 
TABLE 16 
PROGRAM 100 
TOLL RESTRICTION SYSTEM PARAMETERS 
(DIALING PLAN) ’ 
1 SET LED on. 
1) Lock in the 
SET switch on the HKSU. I 
Station 17 REP LED on. 
System is in program mode. 
2) Depress the mkey on station 17. Normal functions halt on station 17. 
SPKR LED steady on. 
3) Dial 0 1 m on the dial pad. SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Turn the associated LED on for the display plan be on. 
to be used. Only one LED may be on at one If the LED is already on, depressing the as- 
time. sociated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
5) Depress them key to place new data in All station 17 LEDs (except REP) go’off. New 
memory. data is stored, previous data is erased. 
6A) Go to Step 2 
in another program table 
. . or . . . 
66) Transfer data into working memory per SET LED goes off. 
Paragraph 02.06. Station 17, REP LED goes off. 
New data IS stored, previous data is erased. 
, 
-29-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 
1986 
TABLE 17 
PROGRAM 101 
TOLL RESTRICTION DISABLE 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
2) Depress the m . key on station 17. 
3) Dial 0 fl 0 on the dial pad. 
4) Refer to the System Record Sheet. 
This program either enables or disables the toll 
restriction for each CO line in the system. Each 
CO key/LED represents itself--that is, if CO 
I 
LED is on, toll restriction is not applied to that 
CO line; if CO1 LED is off, toll restriction is 
applied to that CO line. 
5) Depress them key to place new data in 
memory. Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the as- 
sociated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
Initialized Data: All LEDs off. 
All station 17 LEDs (except REP) got off. _ 
6A) Return to Step 2 in order to continue 
with this program 
6B) Go to Step 2 in aonbther program table 
. . . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
A 
-3o-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
. 
TABLE 18 
PROGRAM 102 
FORCED ACCOUNT CODE CHECK 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. 
/ key on station 17. 
2) Depress the 
l 
3) Dial 0 1 a on the dial pad. 
4) Refer to the System Record Sheet. 
This program determines whether Forced 
Account Codes will be checked on a CO-line- 
by-CO-line basis. Using themkeys, turn their 
associated LEDs on or off, as required. 
0 LED on = Forced Account Codes are checked. 
l Each CO key/LED represents itself-that is, 
if the CO 1 LED is on, stations calling out 
over CO1 will be forced to enter an account 
code. 
5) Depress them key to place new data in All station 17 LEDs (except REP) go off. 
memorv. 
64 Return to Step 2 in order to continue with 
this program 
56) 
5C) Go to Step 2 i’n aE:ther program table 
. . .or.. . 
Transfer data into working memory per 
Paragraph 02.06. 
‘VOTE: 
Program 0#2 defines account code digit length. 
Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
SPKR LED steadv on. 
SPKR LED .flashes continuously. 
CO LEDs go on according to present data. 
An X on the record sheet means the LED should 
be on. 
If the LED is already on, depressing the as- 
sociated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
tern is set. 
Initialized Data: All LEDs off. . 
SET LED goes off. 
Station 17 REP LED goes off. 
New data is stored, previous data is erased. 
-31-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 19 
PROGRAM 103 
EQUAL ACCESS #l 
1 SET LED on. 
1) Lock in the 
SET switch on the HKSU. 
I Station 17 REP LED on. 
System is in program mode. 
LEDs as shown below. 
Initialized Data: Blank (AD4 flashing). 
X = LED on 
All LEDs off = no data 
memory. 
New data is stored, previous data is erased. 
6A) Return to Step 2 in order to continue 
with this program 
6B) Go to Step 2 in azther program table 
. . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 REP LED goes off. 
-32-