Toshiba Strata Se, Strata Vie General Description Manual

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUCIRY : 988 
TABLE 49 
PROGRAM 3XX 
STATION CO LINE ACCESS 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
Normal functions halt on station 13/l 7. 
2) Depress the m key on station 13/l 7. 
SPKR LED steady on. 
3) Dial 3flIon the dial pad (XX = the number of 
the station(s) to be programmed). SPKR LED flashes continuously. 
The CO LEDs indicate present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED shoulc 
Using the appropriate keys, turn their asso- 
be on. 
ciated LEDs on or off, as required. 
l LED ON = Access allowed. If the LED is already on, depressing its associatec 
l Each CO key/LED represents itself-that key will turn it off and vice versa. LEDs may be 
is, if LED 01 is on, then the station being turned off and on until the desired pattern is set. 
programmed (XX) is allowed access to 
CO1 , etc. 
5) Depress the m key to place new data in 
All station 13117 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
66) Go to Step 2 in’an:ther program table 
. . . or . 
6C) Transfer data into working memory per Par- 
agraph 02.06. 
. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
For multiple statlor! ,9 
rcgrzcming, refer to P3ragrap.C: C2.10. 
-75-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 50 
PROGRAM 3#XX 
HOXB, HMDB and HIOB ENABLE 
1) Lock in the SET switch on the HKSU. 13/l 7 LED 19 on. 
‘s in program mode. 
If the LED is already on, depressing the associated 
key 
will turn it off and vice versa. LEDs may be 
(if any key/LED is not shown, it is not turned off and on until the desired pattern is set. 
6B) Go to Step 2 in’a,“,ther program 
table 
or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE, 
For multiple station programming, refer to Paragraph 
02.10. 
-76-  
						

							TABLE 51 
PROGRAM 4XX 
STATION TYPE ASSIGNMENT 
(This program must be completed before Program 4#XX./ 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED 19 on. s 
System is in program mode. 
Normal functions halt on station 13/17. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial gag on the dial pad (XX = the number of 
SPKR LED flashes continuously. 
the station(s) to be programmed). The CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. If the LED is already on, depressing its associated 
key will turn it off and vice versa. LEDs may be 
turned off and on until the desired pattern is set. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
66) Go to Step 2 in’an:ther program table 
. . . or . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
NOTE: 
For multiple station programming, refer to Paragraph 02.10. 
KEY/LED j FEATURE 
/ I 
05 Pattern A 
03 Single-line EKT 
01 lo-key EKT 
00 20-kev EKT 
-77-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 52 
PROGRAM 4#XX 
STATION FLEXIBLE KEY ASSIGNMENTS 
(IMPORTANT! LCD EKT HIGHLY RECOMMENDED) 
(Do Program 4XX for all stations before this program.) 
SET LED 
on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. ’ 
Normal functions halt on station 13117. 
2) Depress the ‘m key on station 13/l 7. 
SPKR LED steady on. 
3) Dial gjfla on. the dial pad (XX = the number SPKR LED flashes continuously. 
of the station(s) to be programmed). 
4) Refer to the System Record Sheet. 
The feature currently assigned to the code number 
Depress the key to be programmed. for that key is displayed by the LCD 
(see table 
below). 
5) Dial in the new feature’s number. The mean- The new feature’s number is displayed on the LCD 
ing of each feature code-is shown below. (see table below). 
6) Continue returning to Step 4 until all desired 
features for the chosen station(s) are pro- 
grammed. 
7) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
8A) Return to Step 2 in order to continue with 
this program 
86) Go to Step 2 in’an$ner program table 
. . . or . . . 
8C) Transfer data into working memory per Pa- 
ragraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTES. 
1. For multiple station programming, refer to Paragraph 02.10. 
Modem Ans/Call 93 
03 co3 
81 95 I 
04 co4 82 3ZF4 . 96 
05 co5 83 97 
06 CO6 84 98 i 
l * * m Ke 
Locked I 
I 78 Modem MM/MA 90 I 
2. All codes can be assiqned only once Der EKT. If assiqned more than once, keys become A ID keys. 
-78-  
						

							TABLE 53 
PROGRAM 5XX 
STATION CLASS OF SERVICE #1 PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY : 388 
1) Lock in the SET switch on the HKSU. 
Using the appropriate keys, turn their asso- 
ciated LEDs on or off, as required. If the LED is already on, depressing the associated 
key will turn it off and vice versa. LEDs may be 
, included 
All Call Page 
! Allowed 
Auto.Callback Warning Tone I Not Allowed 
Handsfree Answerback 
Disabled 
MIC on at start of call 
On 
MIC key lock 
Allowed 
Speakercrhone 
1 Enabled / Not Included 
Not Allowed 
Allowed 
Enabled 
Off 
Not Allowed 
! Disabled 
5) Depress the irr;m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
66) Go to Step 2 in’an$her program table 
. * . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
For multiple station programming, refer to Paragraph 02.10. 
-79-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 54 
PROGRAM 5#XX 
STATION CLASS OF SERVICE #2 
1) Lock in the SET switch on the HKSU. SET LED on. 
Station 13/l 7 LED 19 on. 
System is in program mode. 
Normal functions halt on station 13117. 
ciated LEDs on or off, as required. If a 
key/LED is not shown, it is not used. 
/ - 
09 Automatic Busy Redial Access 
Enable ! Disabled 
07 - 04 Automatic Off-hook Selection (94 - 91) 
Enable / Disabled 
03 
Automatic Off-hook Selection (COl) 
Enable ! Disabled 
02 Automatic Off-hook SelectIon (INT) 
! Enable / 
/ Disabled 
01 Ringing Line Preference 
I Enable 1 Disabled 
00 Automatic Dialing 
5) Depress the m key to place new data in 
memorv. 
6A) Return to Step 2 in order to continue with 
this program 
66) Go to Step 2 in’anyther program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. 
( Allowed / Not Allowed 
All station 13/l 7 LEDs (except 19) go off. 
SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTES. 
1. For multiple station programming, refer to Paragraph 02.10. 
2. If a station is programmed to automatically select a trunk group (9 or 9 1 - 94), it will select the 
last available line in that group unless a line in that group is ringing--it will select the ringing 
line. 
-8O-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 55 
PROGRAM 6XX 
STATION TOLL RESTRICTION/LCR CLASSIFICATION 
1) Lock in the SET switch on the HKSU. 
this program 
. . . or . . . 
6B) Go to Step 2 in another program table 
. . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
“NOTES. 
1. For multiple station programming, refer to Paragraph 02.20. 
2. See Toll Restriction; 
Programs 100, 1 Xl, 1XY. 1XZ. and 2XY. 
-81-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 56 
PROGRAM 6#XX 
STATION-TO-STATION HUNTING 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 13/17. 
3) Dial igag on the dial pad (XX = the number 
of the station(s) to be programmed). 
4) Refer to the System Record Sheet. 
This program defines the station hunt desti- 
nation. Dial the 2-digit number using the dial 
pad. 
11 I 1 Steady 
10 1 Flash 1 Steady 1 
Binary Numbers: 1 2 3 4 5 6 7 8 9 0 
03 x x x 
X = LED on 
02 
x x x x 
All LEDs off 
q no data 
01 x x x x X 
X X X X 
All station 13/l 7 LEDs (except 19) go off. 
New data is stored, previous data is erased.  5) Depress the m key to place new data in 
memorv. SET LED on. 
Station 13/l 7 LED 19 on. 
System is in program mode. 
Normal functions halt on station 13117. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
The various LEDs indicate present data. 
As each digit is entered, the entry is verified by 
LEDs as shown below. 
Key/LED1 Start 1 1st Digit 1 2nd Digit 
6A) Return to Step 2 in order to continue with 
this program 
or . . . 
613) Go to Step 2 ‘in another program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off 
NOTE: 
For multiple station programming, refer to Paragraph 02.10. 
-82-  
						

							PROGRAMMING PdOCEDURES 
SECTION 500-036-300 
JANUARY 
1988 
TABLE 57 
PROGRAM 7XX 
STATION OUTGOING CALL RESTRICTION 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13117 LED 19 on. , 
System is in program mode. 
Normal functions halt on station 13/17. 
2) Depress the m key on station 13/l 7. 
SPKR LED steady on. 
3) Dial Gaa on the dial pad (XX = the number of 
SPKR LED flashes continuously. 
the station(s) to be programmed). 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using the approcriato keys, turn their asso- 
be on. 
ciated LEDs on or off, as required. 
If the LED is already on, depressing its associated 
l LED ON = Restricted outgoing calls. 
key will turn it off and vice versa. LEDs may be 
l Each CO key/LED represents itself-that 
turned off and on until the desired pattern IS set. 
is, if LED 01 is on, then the station being 
programmed (XX) is restricted from outgo- 
ing calls on COl, etc. 
5) Depress the m key to place new data in 
All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
6B) Go to Step 2 in’an:ther program table 
. or . 
6C) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
For multiple station programming, refer to Paragraph 02.10. 
-83-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 58 
PROGRAM 81XX - 89XX 
CO RINGING ASSIGNMENTS (DAY/DAYZ/NIGHT) 
1) Lock in the SET switch on the HKSU. 
2) Depress the em key on station 13/17. 
3) Dial 3aafl on the dial pad (Y = 1 - 9”; XX = 
the number of station(s) to 
be programmed). 
4) RefeF to the System Record Sheet. 
Using the appropriate keys, turn their asso- 
ciated LEDs on or off, as required. 
l LED ON = Ringing assigned. 
l Each CO key/LED represents itself-that 
is, if LED 01 is on, then the station being 
programmed (XX) is allowed access to 
CO1 , etc. 
5) Depress the m key to place new data in 
memorv. 
6A) Return to Step 2 in order to continue with 
this program 
6B) Go to Step 2 in’an:ther program table 
. . or . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED on. 
Station 13/l 7 LED 19 on. 
System is in progra’m mode. 
Normal functions halt on station 13/17. 
SPKR LED 
steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
An X on the record sheet means the LED sho( 
be on. 
If the LED is already on, depressing its associat 
key will turn it off and vice versa. LEDs may 
turned off and on until the desired pattern is s 
All station 13/l 7 LEDs (except 19) go off. 
SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
l l = DAY-immediate 
2 = DAY-l 2-seconds delay 
3 = DAY--24~seconds delay 
NOTE: 4 = DAY 2-immediate 7 = NIGHT-immediate 
5 = DAY 2-l 2-seconds delay 8 = NIGHT-l 2-seconds delay 
6 = DAY 2-24-seconds delay 9 = NIGHT-24-seconds delay 
For multiple station programming, refer to Paragraph 
02.10.