Toshiba Strata Se, Strata Vie General Description Manual

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 9 
PROGRAM 03 
SYSTEM ASSIGNMENTS ,(OPTIONS) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. ’ 
Normal functions halt on station 13/17. 
2) Depress the m key on station 13/l 7. 
SPKR LED steady on. 
3) Dial 13 on the dial pad. SPKR LED flashes continuously. 
The various LEDs indicate present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED shoulc 
Using the various keys, turn their associated 
be on. 
LEDs on or off, as required. The detailed 
If the LED is already on, depressing the associatec 
meaning of each key/LED is shown below. 
key will turn it off and vice versa. LEDs may be 
NOTE. turned off and on until the desired pattern is set 
lf any key/LED is not shown, it is not used. 
KEY/LED 
LED ON LED OFF 
--JO 
_ StationlO~key-._---s - ~~__- _._ ~~. __ .mkey_ __ ..--~ __-. 
09 Station 10-m key ~~ _- m key 
08 
_ - .- _~- 3-ring Mode 
..- 2-ring Mode 
07 CO Line Groups-Allowed. Not Allowed 
04 --Message Center-Station 12 Not Equipped 
~~ 03 .---_- -..--  Message Center+tation 11 ._ _. _ Not Equipped 
02 Message Center-Station 10 --Not Equipped- 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . 
68) Transfer data into working memory per Par- 
agraah 02.C6. SET i.F13 y?3 off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased 
- *Voice First must be optioned for Off-hook Call Announce. 
-35-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 10 
PROGRAM 04 
CO LINE OUTPULSING SELECTION 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. 
2) Depress the m key on station 13/l 7. 
3) Dial li on the dial pad. Station 13/l 7 LED 19 on. 
System is in program mode.. 
Normal functions halt on station 13117. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Each CO key/LED represents itself; depress be on. 
the required keys. If the LED is already on, depressing the associated 
l LED OFF = DTMF tone operation. key will turn it off and vice versa. LEDs may be 
l LED ON = Dial Pulse (DP) operation. turned off and on until the desired pattern is set. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
-36-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 11 
PROGRAM #4-CO LINE IDENTIFICATION 
(LCD EKT Required) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. 
Normal functions halt on station 13/l 7. 
LCD is in program mode. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
LCD: Program No.?. 
3) Dial 91 on the dial pad SPKR LED flashes continuously. 
LCD displays program number. 
4) Refer to the System Record Sheet. Cursor appears in LCD display. 
Depress the required key, and enter the CO LCD displays characters as they are entered. 
iine name, as defir.ed in the System Record 
Sheet, via the dial pad. 
a) Depress the 3 key to access alpha charac- 
ters. 
b) Move the cursor to the desired position (the 
left edge of the display for a new message, 
two spaces to the right of the preprogrammed 
message to add information). 
c) Depress the key with a letter you wish to en- 
ter. Use the 3 key to shift from letter to letter 
on the key. For example: 
l If you press 1 , a D will be displayed. By 
pressing 3, the D is changed to E. Bypress- 
ing a again, the E is changed to F. Press a 
again and the F changes to D. 
l To enter spaces, press fl . 
d) If want to enter a number, press the 1 key 
to change to numeric characters. Numbers 
are also entered on the dial pad. Press the 2 
key again to return to alpha characters. 
e) The fo!!owing specia! characters are set by 
pressingfland then pressinglto step through 
the available characters: Q, 
Z, :, -, +, 1. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
or . . . 
6B) Go to Step 2 in’another program table 
. . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
-37-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 12 
PROGRAM 05 
AUTOMATIC RECALL FROM HOLD TIMING 
(This program is used only if LEDs 10, 1 I and 12 are ALL off in Program 5#XX.) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. .% 
Normal functions halt on station 13117. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial 3 i on the dial pad. SPKR LED flashes continuously. 
One LED indicates present data. 
4) Refer to the System Record Sheet. An 
X on the record sheet means the LED should 
Using the various keys, turn an associated be on. 
LED on or off, as required. The detailed mean- Only one LED is permitted to be on, depressing an- 
ing of each key/LED is shown below. other key will turn that LED on and turn off the pre- 
NO TE. vious LED. 
If any key/LED is not shown, it is not used. 
KEY/LED 
LED ON 
07 
160 seconds 
06 
128 seconds 
05 96 seconds 
04 
64 seconds 
03 48 seconds 
~.___- 
02 
32 seconds 
-- 
01 16 seconds 
00 
No Recall 
5) Depress the 3;m key to place new data in All station 13/17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
6B) Transfer da!a into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/l 7 
LED 19 goes off. 
New data is stored, previous data is erased. 
-38- x  
						

							TABLE 13 
PROGRAM 0#5 
CAMP-ON TIMEOUT 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. ’ 
Normal functions halt on station 13/l 7. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial a f 1 on the dial pad. SPKR LED flashes continuously. 
One LED indicates present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using the various keys, turn an associated be on. 
LED on or off, as required. The detailed mean- Only one LED is permitted to be on; depressing 
ing of each key/LED is shown below. another key will turn that LED on and turn off the 
NOTE. previous LED. 
if any key/LED is not shown, it is not used.. 
KEY/LED 
LED ON 
03 
64 seconds 
02 
48 seconds 
01 
32 seconds 
00 16 seconds 
5) Depress the m key to place new data in 
All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Pa- 
ragraph 02.06. 
SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased.  PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
-39-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 14 
PROGRAM 06 
AUTOMATIC RELEASE ON HOLD ENABLE 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. , 
2) Depress the m key on station 13/l 7. 
3) Dial a 1 on the dial pad. Normal functions halt on station 13/l 7. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the various keys, turn their associated be on (AROH enabled). 
LEDs on or off, as required. Each CO key/LED If the LED is already on, depressing the associated 
represents itself-that is, if LED 01 is on, CO1 
key will turn it off and vice versa. LEDs may be 
will have AROH during normal operation. If 
turned off and on until the desired pattern is set. 
k:f 01 is off, AROH will not function on that 
5) Depress the m key to place new data in All station 13/17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTES. 
1. This program is used to release Trunk-to-Trunk connections if enabled with 
Programs 02 and 
0#6. 
2. If Automatic Release from Hold is available, the CO will automatically drop the lines when the 
outside party hangs up. However, if Automatic Release from Hold is not available, the person who 
set up the trunk-to-trunk connection must occasionally monitor the call and disconnect the 
CO 
lines when the two parties hang up. 
-4o-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 15 
PROGRAM 0#6 
TRUNK-to-TRUNK CONNECTION ENABLE 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. 
2) Depress the w key on station 13/l 7. 
3) Dial 111 on the dial pad. Normal functions halt on station 13/l 7. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using the various keys, turn their associated be on. 
LEDs on or off, as required. Each CO key/LED 
If the LED is already on, depressing the associated 
represents itself-that is, if LED 01 is on, CO1 
key will turn it off and vice versa. LEDs may be 
will be allowed trunk-to-trunk connection, if 
turned off and on until the desired pattern is set. 
LED 01 is off, trunk-to-trunk connection will 
not be allowed on that line, etc. 
5) Depress the m key to place new data in 
All station 13117 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
or . . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
*New data is stored, previous data is erased. 
-41-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 16 
PROGRAM 07 
AUTOMATIC RELEASE ON HOLD TIMING 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. .( 
2) Depress the m key on station 13/17. 
3) Dial ii on the dial pad. Normal functions halt on station 13/l 7. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. Each CO If the LED is already on, depressing the associated 
key/LED represents itself-that is, if LED 01 key will turn it off and vice versa. LEDs may be 
is on, CO1 will have Xl3 (crossbar) timing for turned off and on until the desired pattern is set. 
AROH. If LED 01 is off,-CO1 will have ESS 
(electronic) timing, etc. 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
68) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
This program affects only those CO lines enabled via Program 06 (AROH should be enabled for 
Trunk-to-Trunk connections). 
-42-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 17 
PROGRAM 0#7 
AUTOMATIC RELEASE ON HOLD TIMING 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. ’ 
2) Depress the m key on station 13/l 7. 
3) Dial ljd on the dial pad. Normal functions halt on station 13/l 7. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- 
be on. 
ciated LEDs on or off, as required. Each CO 
If the LED is already on, depressing the associated 
key/LED represents itself-that is, if LED 01 
key will turn it off and vice versa. LEDs may be 
is on, CO1 is bridged with-the lA2 system. If 
turned off and on until the desired pattern is set. 
LED 01 is off, CO1 is not bridged, etc. 
5) Depress the m key to place new data in 
All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
-43-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 18 
PROGRAM 08 
CO LINE CALL PICKUP SELECTION 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. 
2) Depress the tm key on station 13/17. 
3) Dial 13 on the dial pad. Station 13/17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 13/l 7. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the appropriate keys, turn their asso- be on. 
ciated LEDs on or off, as required. Each CO If the LED isalready on, depressing the associateci 
key/LED represents itself-that is, if LED 01 key will turn it off and vice versa. LEDs may be 
is on, CO1 will belong to CPU #2. If LED 01 turned off and on until the desired pattern is set. 
is off, CO1 will belong -to CPU #l, 
5) Depress the m key to place new data in All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go to Step2 in another program table 
or . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
NOTE. 
This program will have no meaning unless Call Pickup was selected in 
Program 03. 
-44-