Toshiba Strata S Electronic Key Telephone System Installation And Maintenance Manual

TOSHIBA SYSTEM PRACTICES 
ELECTRONIC KEY TELEPHONE SYSTEM 
Strata S SYSTEM PROGRAMMING 
SECTION 1 oJo;I$3;;: 
PROGRAMMING PROCEDURES  

TOSHIBA SYSTEM PRACTICES 
ELECTRONIC KEY TELEPHONE SYSTEM 
FCC REGISTRATION TOSHIBA PUBLICATIONS 
SECTlON 100-003-000 
JULY 1984 
The 
Strata S electronic key telephone sys- 
tem is registered in accordance with the provi- 
sions of Part 68 of the Federal Communications 
Commission’s Rules and Regulations. 
FCC REQUIREMENTS 
Means of Connection 
The Federal Communications Commission (FCC) 
has established rules which permit the 
Strata 
S electronic key telephone system to be con- 
nected directly to the...

TOSHIBA SYSTEM PBACTICES SYSTEM PROGRAMMING 
ELECTBONIC KEY TELEPHONE SYSTEM SECTION 100-003-300 
e.. 
JULY 1984 
Strata S 
SYSTEM PROGRAMMING PROCEDURES 
TABLE of CONTENTS 
PARAGRAPH SUBJECT 
PAGE 
01 
02 
02.00 
02.10 
02.20 
02.30 
02.40 
02.50 
02.60 
02.70 TABLE of CONTENTS 
........................ i 
INTRODUCTION 1 
PROGRAMMlNGPkdCEdUkES”::::::::::::::::::: 1 
General 
............................. 1 
Multiple Station Programming 
................... 2 
Preparation 
........................... 2 ....

01 INTRODUCTION 
01 .Ol The data governing overall system opera- 
tion and feature execution for Strcrm S is 
stored in read-only-memory (ROM) and cannot 
be altered in the field. However, thedata control- 
ling operation of the various options, both sys- 
tem and station, is stored in random-access- 
memory (RAM) and can easily be changed ac- 
cording to individual installation requirements. 
01.02 All Stretir S options are controlled 
by selections made in the system data tables. An 
initialization...

SYSTEM PROGRAMMING 
SECTION 1 W-993-399 
JULY 1994 
m.. 
are effective immediately after the I=] key 
is depressed. However, it is recommended that 
the data transfer procedures per Paragraph 
02.06 be utilized for added programming 
protection. 
02.06 Data may be secured in working memory 
as follows: 
l Release the SET switch on the switch panel, 
and cycle (rock) the MKSU power switch OFF 
and ON to transfer all data into the main data 
memory. Note, all calls are dropped when this 
occurs. 
02.10...

5) 
6) 
is to be 0.5-second for behind PBX operation. 
Leave blank if the 2.0-second flash for dial 
tone recall is required. 
Station 10 DND/NITE Key-mark an X next to 
CO 1 if the IDND/NITEJ key on station 10 is to be 
a DND key. leave blank if mkey is required. 
Tone First-mark an X next to INT if Tone First 
intercom signalling is required. Leave blank if 
Voice First signailing is required. 
05 Program-Automatic Recall From Hold Timing 
Sets the timing for the Automatic Recall From 
Hold feature....

SYSTEM PROGRAMMING 
SECTlON 100-903-399 
JULY 1994 
e.. 
1) Mark an X next to CO 2 if the EKT is equipped 
with 1 O-key #2 or 20-key #3 configuration. 
2) MarkanXnexttoCO 1 iftheEKTistohavethe 
1 O-key #l or 20-key #2 configuration. 
3) Mark an X next to INT if the EKT is to have the 
1 O-key #l or 20-key #l . 
NOTE: 
Instructions #I and #3 cover all available 
EK Ts, #2 is a 20-key exclusive (see Figure 1 I. 
5XX Program-Station Class of Service 
Six options are selected with this program, 
using m, a...

1 O-key EKT #1 
1 O-key Ett r#2 20-key EKT ##1 
20-key EKT #2 
PO-key EKT ##3 
YW/FL 
b-4 
1 DND 1 
I MW/FL 
I DND 
I I AD4 I REP 
I I AD 3 
I I AD 2 I PAU 
AD 1 
H CD 3 I CD 3 
I CD 2 
I CD 1 
FIG1 SYSTEM PROGRAMMING 
SECTION 100-003-300 
JULY 1994 
RE l-EKT KEY ASSIGNMENTS 
-5-  

SYSTEM PROGfIAMMlNG 
SECTlON 1 W-993-399 
JULY 1994 
v.. 
TABLE 1 
SYSTEM RECORD SHEET 
PROGRAM 01 -SYSTEM ASSIGNMENTS 
X = Select (LED on) Initialized Data: AD 4 LED on; all other LEDs off 
NOTE: 
Only one Message Center is permitted; if both stations 10 and 11 
are chosen as Message Centers. station IO will have priority. 
PROGRAM 05 
AUTOMATIC RECALL FROM HOLD TIMING 
KEY/LED X TIME 
A04 160 Seconds 
AD3 128 Sfxotlds 
A02 96 Seconds 
AD1 64 Seconds 
co3 46 seconds 
co2 32 Seconds 
co 1 16 Seconds 
IN1...

SYSTEM PROGRAMMING 
SECTION 100-003-3790 
JULY 1994 
PROGRAM lo-PBX BACKUP 
X = Connected to PBX line (LED on) 
Initialized Data: All LEDs off 
PROGRAM 1X-PBX ACCESS CODES 
NOTE: 
Enter Access Codes (maximum: 8) 
Initialized Data: None 
If the access code is a single digit, enter “**’ in the second column. If all 
combinations following a particular first digtl are to be considered access 
codes (e.g., 9 I, 92,93, etc.), enter “D” (do not care) in the second column. 
PROGRAM 20~TOLL RESTRICTION DISABLE...