Toshiba Strata Dk Admin/ Dk Backup User Guide

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––Backup Data
101Backup Menu (DKBackup)
The DK System Program File screen displays listing the available data for backup (see 
screen in Step 3). For security, this code does not display on screen as you type it. The 
default code is 0000. This is the “1st level password” which is set in the Strata DK 
Program 00 (see the record sheet for Program 00 in the Strata DK Programming Manual).
NoteIf the Problem: Unable to Establish...

Restore Data––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
102DKAdmin/DKBackup
lThe DK System Program File list is displayed (see Step 3 on Page 101). If this screen does 
not display, the DKAdmin/DKBackup PC and the Strata DK are not communicating. See 
Appendix A – Connecting to Strata DK for procedures to connect the PC COM port to the 
Strata DK PIOU, RSSU, RSIS, RSIU, or PIOUS TTY port, or IMDU or RMDS modems.
Important!If the PC screen does not display prompts...

–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––Restore Data
103Backup Menu (DKBackup)
Notes
lWhen you back up PRGALL, the DK security code, set in the DKBackup customer 
database, is not sent to the processor. You must always enter the DK security code that is 
actually programmed on the processor installed in the Strata DK. You can change the DK 
security code using the DKAdmin Program Administration Section option or manually 
using the programming telephone.
lAccess...

Restore Data––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
104DKAdmin/DKBackup
Important!These messages display
6. Press Enter and the following screen displays:
Processor Conversion
PLEASE READ THE FOLLOWING SCREENS AS THEY PROVIDE VERY IMPORTANT 
INFORMATION REGARDING THE UPGRADE AND INITIALIZATION PROCESSES.
Please turn DK system power off and add/change cabinets, processor ROM or 
RMSS memory and/or RCTU PCBs as required.
IMPORTANT: Do not add PCBs, other than RSIU...

–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––Restore Data
105Backup Menu (DKBackup)
7. After completing the steps on the screen, press Enter (twice) and the Baud Rate 
Selection screen displays (shown below). This screen enables you to set the DKAdmin/
DKBackup PC COM port baud rate which must match the baud rate of the TTY or modem 
port set by the programming telephone.
8. Select the DKAdmin/DKBackup PC COM port baud rate and press Enter. The 
information screen...

Restore Data––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
106DKAdmin/DKBackup
9. After reading the screen in Step 7, press Enter. The screen below displays.
10. Highlight Yes and press Enter. You are prompted for the DK Code.
11. Enter the four-digit DK Code.
Important!You must enter the code programmed on the installed processor.
DKAdmin/DKBackup turns on LED10 in Program 77-1 and then displays the message 
“You will send data to the DK. Are you sure?”
12. Highlight...

–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––Upgrade
107Backup Menu (DKBackup)
16. Press Enter from the screen above. DKAdmin/DKBackup runs Program 91-2 and then 
displays the message Program 91-2 has been completed. The system 
has performed a power off/on simulation.
17. After the above screen displays, press any key. The restore process has been completed. 
You may use the Esc key to exit to the top menu.
Important!
lIf you restore (send) PRGALL to the Strata...

Upgrade––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
108DKAdmin/DKBackup
lWhen upgrading from an RCTU Release 1 or 2 to an RCTU Release 3 or above, 
DKAdmin/DKBackup automatically converts Program 39 intercom code (000) to the 
appropriate Primary Directory Number code (##XXX) for each station port.
lWhen upgrading from DK16e and RCTUA to RCTUB or C/D (all releases), System 
Speed Dial numbers and buttons (060~099) are upgraded to (660~699).
lWhen upgrading to an...

–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––Upgrade
109Backup Menu (DKBackup)
If the following message displays: Problem: Unable to Establish 
Communications, follow the steps on the screen and/or refer to Appendix A – 
Connecting to Strata DK to correct the problem.
4. From the Administration Menu/Backup Menu, type b. The DK Code dialog box displays.
5. Enter the four-digit DK Code that is programmed on the installed processor. The DK 
System Program File screen...

Upgrade––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
110DKAdmin/DKBackup
8. Press Enter and then select the processor type you are upgrading to; press Enter after 
selecting the processor (RDTU E/F, Release 3 in this example).
9.If you haven’t backed up the customer database by downloading the original RCTU, 
answer Yes to Backup From DK First; otherwise, answer No. Press the spacebar to 
make your selection and then press Enter.
10. From the screen in Step 7...